Difficulty: Hard
A simple planetary set has sun 30 teeth, ring 70 teeth; ring is fixed and sun turns 3,000 rpm. Carrier speed?
A 1,286 rpm
B 2,100 rpm
C 900 rpm
D 3,000 rpm
Answer: C. 900 rpm. With ring fixed, carrier speed=Ns/(Ns+Nr)×sun speed=30/100×3,000=900 rpm.
What determines a planetary transmission’s selected ratio?
A Oil color
B Member selection sets ratios
C Tire pressure
D Radiator airflow
Answer: B. Member selection sets ratios. Clutches and brakes hold or drive different planetary members to create ratios.
A gear has 120 mm pitch diameter and 40 teeth. Module?
A 2 mm
B 4 mm
C 6 mm
D 3 mm
Answer: D. 3 mm. Module=pitch diameter/tooth count=120/40=3 mm.
Module is 2.5 mm and a gear has 48 teeth. Pitch diameter?
A 96 mm
B 48 mm
C 120 mm
D 192 mm
Answer: C. 120 mm. Pitch diameter=module×teeth=2.5×48=120 mm.
Two external gears have 30 and 70 teeth with module 2 mm. Centre distance?
A 80 mm
B 100 mm
C 120 mm
D 200 mm
Answer: B. 100 mm. Pitch diameters are 60 and 140 mm; centre distance=(60+140)/2=100 mm.
A spur gear has module 3 mm. Circular pitch is approximately?
A 6.00 mm
B 3.14 mm
C 18.85 mm
D 9.42 mm
Answer: D. 9.42 mm. Circular pitch=πm=π×3≈9.42 mm.
A 40-tooth gear runs at 900 rpm. Gear-mesh frequency?
A 40 Hz
B 360 Hz
C 600 Hz
D 900 Hz
Answer: C. 600 Hz. Mesh frequency=40×900/60=600 tooth engagements per second.
Pitch diameter is 0.20 m and speed is 900 rpm. Pitch-line velocity?
A 4.71 m/s
B 18.85 m/s
C 28.27 m/s
D 9.42 m/s
Answer: D. 9.42 m/s. v=πdN/60=π×0.20×900/60≈9.42 m/s.
Torque is 250 N·m at a 0.10 m pitch radius. Tangential tooth force?
A 1,250 N
B 2,500 N
C 5,000 N
D 25,000 N
Answer: B. 2,500 N. Tangential force=T/r=250/0.10=2,500 N.
A gear pair has contact ratio 1.6. What does this imply?
A No teeth touch
B Exactly one tooth pair always
C Gears cannot transmit torque
D Two pairs engage part-cycle
Answer: D. Two pairs engage part-cycle. A ratio above one means one pair remains engaged while a second pair shares contact for part of the cycle.
What is backlash between meshing gear teeth?
A Small clearance between teeth
B Pitch diameter difference
C Oil-film thickness
D Shaft angular twist
Answer: A. Small clearance between teeth. Backlash is the clearance between mating tooth flanks when direction reverses.
What axial load can a helical gear generate?
A Thrust along shaft
B Only radial load
C No bearing load
D Fuel-line pressure
Answer: A. Thrust along shaft. The helix angle creates an axial thrust component that needs support.
Which ideal gear type has no axial thrust from tooth helix?
A Spur gear
B Helical gear
C Worm gear
D Hypoid gear
Answer: A. Spur gear. Straight spur teeth have no helix-angle thrust component.
What operating condition can promote gear scuffing?
A Low tire pressure
B High sliding with poor lubrication
C Coolant overfill
D Low fuel octane
Answer: B. High sliding with poor lubrication. High sliding contact and a weak lubricant film can cause adhesive scuffing.
Repeated bending stress at a tooth root can cause what?
A Fuel dilution
B Coolant cavitation
C Valve-seat recession
D Bending fatigue crack
Answer: D. Bending fatigue crack. Cyclic tooth-root bending can initiate fatigue cracks and eventual tooth failure.
Gear teeth contact heavily at one edge. What may be misaligned?
A Fuel injectors
B Radiator fins
C Shafts or gear mounting
D Steering wheel
Answer: C. Shafts or gear mounting. Shaft or gear misalignment can concentrate load at a tooth edge.
What do splines allow while transmitting torque?
A Fluid cooling only
B Gear ratio control
C Axial sliding when designed
D Exhaust gas flow
Answer: C. Axial sliding when designed. Splines transmit torque and may permit axial sliding between connected parts.
For T=200 N·m, L=0.5 m, J=2×10⁻⁶ m⁴, G=80 GPa, shaft twist?
A 0.00625 rad
B 0.000625 rad
C 0.0625 rad
D 0.625 rad
Answer: B. 0.000625 rad. θ=TL/JG=100/(2×10⁻⁶×80×10⁹)=0.000625 rad.
For T=150 N·m, r=0.015 m, J=1.5×10⁻⁶ m⁴, maximum shear stress?
A 0.75 MPa
B 3.0 MPa
C 1.5 MPa
D 15 MPa
Answer: C. 1.5 MPa. τ=Tr/J=150×0.015/(1.5×10⁻⁶)=1.5 MPa.
Why can one Cardan joint at an angle cause speed fluctuation?
A It changes gear tooth count
B It stops torque transfer
C Cyclic output-speed variation
D It raises oil viscosity
Answer: C. Cyclic output-speed variation. A single angled universal joint produces cyclic output-speed variation.
How can paired Cardan joints reduce speed fluctuation?
A Equal angles and correct phasing
B Different shaft speeds
C Removing the slip yoke
D Using no lubrication
Answer: A. Equal angles and correct phasing. Equal working angles and correct phasing largely cancel the first joint’s speed variation.
When can a torque-converter stator one-way clutch hold the stator?
A During torque multiplication
B At every high-speed cruise
C When engine is off
D During neutral only
Answer: A. During torque multiplication. The one-way clutch holds the stator to redirect fluid during torque multiplication.
Why must a CVT belt receive sufficient clamping force?
A Raise engine compression
B Cool the radiator
C Change wheelbase
D Prevent pulley slip
Answer: D. Prevent pulley slip. Clamping force lets the belt transmit torque without slipping on the pulleys.
Why can a CVT hold engine speed near an efficient region?
A Use one fixed gear
B Continuously vary transmission ratio
C Lock both axles
D Change tire diameter
Answer: B. Continuously vary transmission ratio. Continuous ratio adjustment can keep the engine near a chosen efficient or power band.
During an automatic shift, where is much clutch-slip energy dissipated?
A Transmission fluid
B Fuel tank
C Radiator fan
D Tire sidewall
Answer: A. Transmission fluid. Friction elements convert slip energy to heat that the fluid and cooler must carry away.