A power transformer transfers AC energy between windings by which principle?
A Mutual induction
B Electrostatic induction only
C Mechanical commutation
D Chemical reaction
Answer: A. Mutual induction. Changing core flux links primary and secondary and induces EMF.
An ideal transformer changes voltage while leaving which quantity unchanged?
A Current
B Frequency
C Impedance
D Power factor always
Answer: B. Frequency. The output frequency equals the input AC frequency.
Separate primary and secondary windings provide which benefit?
A Frequency conversion
B DC amplification
C Mechanical rotation
D Galvanic isolation
Answer: D. Galvanic isolation. No direct conductive path is required between the two windings.
Which winding receives electrical input from the source?
A Secondary winding
B Primary winding
C Core lamination
D Tank winding
Answer: B. Primary winding. The primary is connected to the input source.
A step-up transformer has secondary voltage relative to primary voltage that is what?
A Lower
B Always zero
C Always equal
D Higher
Answer: D. Higher. A step-up transformer has a higher secondary voltage.
For an ideal transformer, Vp/Vs equals which ratio?
A Ns/Np
B Ip/Is
C Np/Ns
D Frequency ratio
Answer: C. Np/Ns. Induced voltage is proportional to the number of turns.
In an ideal transformer, secondary current relative to primary current follows which turns ratio?
A Ns/Np
B Np×Ns
C Frequency ratio
D Np/Ns
Answer: D. Np/Ns. Current is inversely related to voltage, so Is/Ip=Np/Ns.
A 230 V to 115 V ideal transformer has what primary-to-secondary turns ratio?
A 1:2
B 1:1
C 2:1
D 4:1
Answer: C. 2:1. 230/115=2, matching Np/Ns.
A winding has 100 primary turns and 200 secondary turns. What is Vs/Vp ideally?
A 2
B 0.5
C 1
D 4
Answer: A. 2. Voltage ratio equals Ns/Np=200/100=2.
Transformer nameplate kVA expresses what power quantity?
A Real power only
B Reactive power only
C Mechanical power
D Apparent power
Answer: D. Apparent power. The thermal rating depends on voltage and current, so it is stated in VA or kVA.
Even with the secondary open, why does the primary draw a small current?
A Magnetization and core loss
B Full-load copper loss
C Secondary short circuit
D Mechanical friction
Answer: A. Magnetization and core loss. No-load current establishes alternating flux and supplies iron loss.
Why is a transformer core built from insulated thin sheets?
A Reduce eddy currents
B Increase brush contact
C Eliminate leakage flux
D Raise copper resistance
Answer: A. Reduce eddy currents. Laminations interrupt large circulating paths for eddy currents.
Electrical steel is chosen partly to reduce which core loss?
A Brush friction
B Windage loss
C Armature copper loss
D Hysteresis loss
Answer: D. Hysteresis loss. Suitable magnetic material has a relatively narrow hysteresis loop.
The EMF induced in a transformer winding is caused by what?
A Changing magnetic flux
B Steady DC flux
C Static insulation
D Shaft rotation
Answer: A. Changing magnetic flux. Faraday’s law relates induced EMF to the time rate of change of flux linkage.
For sinusoidal flux, which expression gives RMS induced EMF per winding?
A 4.44fNΦmax
B 2πfN/R
C VI cosφ
D I²R
Answer: A. 4.44fNΦmax. The sinusoidal transformer EMF equation is E=4.44fNΦmax.
At fixed turns, maximum core flux is approximately proportional to what?
A Voltage times frequency
B Voltage divided by frequency
C Current squared
D Winding resistance only
Answer: B. Voltage divided by frequency. From E≈4.44fNΦmax, flux varies with V/f.
Raising voltage at fixed frequency and turns can lead to what core condition?
A Zero flux
B Lower hysteresis always
C Saturation
D No-load current zero
Answer: C. Saturation. A high V/f raises flux density and can drive the core into saturation.
In a shell-type transformer, what surrounds much of the winding assembly?
A Cooling oil only
B Magnetic core
C Secondary load
D Circuit breaker
Answer: B. Magnetic core. The shell-type core provides limbs around the central winding region.
Leakage flux differs from mutual flux because it links what?
A Both windings equally
B Neither winding
C The tank only
D Only one winding
Answer: D. Only one winding. Leakage flux produced by a winding does not fully link the other winding.
Which part of no-load current establishes the main core flux?
A Load component
B Secondary component
C Magnetizing component
D Short-circuit component
Answer: C. Magnetizing component. The reactive magnetizing current supplies the core’s alternating flux.
The core-loss component of no-load current is approximately in phase with what?
A Applied voltage
B Core flux
C Magnetizing current
D Leakage reactance
Answer: A. Applied voltage. Real power loss corresponds to a current component in phase with voltage.
For an ideal transformer, how do input and output real powers compare?
A Input is zero
B They are equal
C Output is doubled
D Output is negative
Answer: B. They are equal. An ideal lossless transformer has Pin=Pout.
A load impedance reflected to the primary changes by what factor when Np/Ns=a?
A a
B 1/a
C a²
D 2a
Answer: C. a². The referred impedance is Zp=a²Zs.
A 10 Ω secondary load is referred through a 2:1 primary-to-secondary turns ratio. What is primary-referred impedance?
A 2.5 Ω
B 40 Ω
C 10 Ω
D 20 Ω
Answer: B. 40 Ω. Zp=(2)²×10 Ω=40 Ω.
Dot marks on transformer windings identify what?
A Grounded terminals only
B Higher-current leads
C Corresponding instantaneous polarities
D Cooling connections
Answer: C. Corresponding instantaneous polarities. Dotted ends have matching instantaneous voltage polarity under the stated reference direction.