A quarter-car has k = 20 kN/m and m = 200 kg. What is its natural frequency?
A About 1.6 Hz
B About 0.8 Hz
C About 3.2 Hz
D About 6.3 Hz
Answer: A. About 1.6 Hz. The undamped frequency is β(k/m)/(2Ο) = β100/(2Ο), approximately 1.59 Hz.
For k = 20 kN/m and m = 200 kg, what is critical damping?
A 4,000 NΒ·s/m
B 2,000 NΒ·s/m
C 8,000 NΒ·s/m
D 10,000 NΒ·s/m
Answer: A. 4,000 NΒ·s/m. Critical damping is 2β(km), which gives 2β(20,000 Γ 200) = 4,000 NΒ·s/m.
A 50 N/mm spring uses a 0.8 motion ratio. What is wheel rate?
A 40 N/mm
B 50 N/mm
C 32 N/mm
D 62.5 N/mm
Answer: C. 32 N/mm. Wheel rate is spring rate times motion ratio squared: 50 Γ 0.8Β² = 32 N/mm.
Two linear springs of 30 and 20 N/mm act in parallel. What is their combined rate?
A 12 N/mm
B 25 N/mm
C 50 N/mm
D 10 N/mm
Answer: C. 50 N/mm. Parallel spring rates add, giving 30 + 20 = 50 N/mm.
Two springs of 30 and 20 N/mm act in series. What is their equivalent rate?
A 50 N/mm
B 12 N/mm
C 25 N/mm
D 10 N/mm
Answer: B. 12 N/mm. For springs in series, inverse rates add: 1/(1/30 + 1/20) = 12 N/mm.
A 0.01 mΒ² air spring has 600 kPa gauge pressure. What force is produced?
A 600 N
B 60,000 N
C 1,600 N
D 6,000 N
Answer: D. 6,000 N. Force is pressure times effective area: 600,000 Pa Γ 0.01 mΒ² = 6,000 N.
A 30 kN/m spring supports 3 kN. What is its static deflection?
A 10 mm
B 30 mm
C 100 mm
D 300 mm
Answer: C. 100 mm. Deflection equals force divided by rate: 3,000 N / 30,000 N/m = 0.1 m.
A damper resists with 800 N at 0.5 m/s. What power is dissipated?
A 160 W
B 400 W
C 800 W
D 1,600 W
Answer: B. 400 W. Dissipated power is force times velocity: 800 Γ 0.5 = 400 W.
Actual damping is 1,500 NΒ·s/m and critical damping is 4,000 NΒ·s/m. What is the damping ratio?
A 0.25
B 0.60
C 2.67
D 0.375
Answer: D. 0.375. Damping ratio is actual damping divided by critical damping: 1,500/4,000 = 0.375.
Road excitation matches the body natural frequency. What response risk rises?
A Resonant body motion
B Zero spring force
C No tire deflection
D Lower damper velocity
Answer: A. Resonant body motion. Excitation near a natural frequency can amplify oscillation unless damping limits the response.
Which motion is usually associated with the higher wheel-hop frequency?
A Unsprung mass oscillation
B Body heave only
C Steering column flex
D Engine roll
Answer: A. Unsprung mass oscillation. Wheel hop is a higher-frequency mode involving tire, wheel, and other unsprung components.
If sprung mass quadruples while spring rate stays fixed, natural frequency becomes what?
A Half as high
B Twice as high
C Four times higher
D Unchanged
Answer: A. Half as high. Natural frequency varies as 1/βm, so four times the mass halves the frequency.
A designer adds front roll stiffness while keeping rear roll stiffness fixed. Which tendency may increase?
A Oversteer
B Understeer
C Ride height
D Wheelbase
Answer: B. Understeer. More front elastic load transfer can reduce front lateral grip relative to the rear.
Roll center height rises substantially. Which effect may become stronger?
A Spring sag
B Geometric jacking
C Damper cavitation
D Wheel hop only
Answer: B. Geometric jacking. Higher geometric force paths can increase vertical jacking components during cornering.
Why can anti-dive links not eliminate braking load transfer?
A Springs stop carrying weight
B Brakes lose torque
C Tires become unsprung
D Vehicle inertia still transfers load
Answer: D. Vehicle inertia still transfers load. Anti-dive changes suspension force paths and pitch motion, while longitudinal load transfer still follows vehicle dynamics.
During acceleration, anti-squat geometry mainly routes force through what?
A Damper oil alone
B Tire tread blocks
C Steering rack
D Suspension links
Answer: D. Suspension links. Link geometry transmits part of the drive-force reaction to oppose suspension compression.
What determines the instantaneous center of a control-arm suspension?
A Tire pressure values
B Spring free lengths
C Damper oil volume
D Projected arm pivot lines
Answer: D. Projected arm pivot lines. In side or front view, the instantaneous center is found from extended lines through relevant suspension pivots.
A tie rod follows a different arc than the suspension arm. What may result?
A Spring-rate increase
B Brake fade
C Toe change through travel
D Lower unsprung mass
Answer: C. Toe change through travel. Mismatched linkage arcs change wheel toe as the suspension moves.
What alignment change can a short upper arm create in bump?
A Positive caster gain
B Negative camber gain
C More toe-in always
D Larger scrub radius
Answer: B. Negative camber gain. A shorter upper arm can pull the top of the wheel inward as the suspension compresses.
Body roll changes wheel steer angle through suspension kinematics. What is this called?
A Brake steer
B Power steer
C Roll steer
D Bump stop
Answer: C. Roll steer. Roll steer is a change in wheel steer angle associated with body roll and suspension geometry.
A jounce bumper engages late in compression. What happens to effective wheel stiffness?
A It rises sharply
B It falls to zero
C It stays unchanged
D It becomes damping only
Answer: A. It rises sharply. The bumper adds a progressive elastic element near the end of compression travel.
What can a semi-active damper change in real time?
A Static wheelbase
B Spring free length
C Tire diameter
D Damping force level
Answer: D. Damping force level. Semi-active systems vary damper characteristics but generally do not command sustained force independently of motion.
What distinguishes active suspension from semi-active damping?
A Actuator can add force
B It has no sensors
C It uses no springs
D It only changes tires
Answer: A. Actuator can add force. An active actuator can apply controlled forces, while semi-active hardware mainly adjusts energy dissipation.
In skyhook-style control, which motion is commonly targeted?
A Tire spin relative rim
B Body velocity relative ground
C Steering angle relative rack
D Spring load relative axle
Answer: B. Body velocity relative ground. Skyhook control uses body motion relative to an inertial reference to reduce sprung-mass movement.
Why can excessive damper force reduce comfort on sharp bumps?
A It raises tire pressure
B It lowers spring rate
C It transmits more impact
D It changes wheelbase
Answer: C. It transmits more impact. Overly high damping can resist rapid wheel movement and transmit more road shock into the body.