Difficulty: Easy & Basic
Spring rate is force divided by what?
A Wheel diameter
B Damper length
C Track width
D Spring deflection
Answer: D. Spring deflection. Spring rate measures the force needed for each unit of spring deflection.
A higher linear spring rate feels how?
A Softer
B More damped
C Less sprung
D Stiffer
Answer: D. Stiffer. A higher rate requires more force for the same spring compression.
What does spring preload establish?
A Damper oil level
B Initial spring compression
C Wheel alignment
D Tire contact patch
Answer: B. Initial spring compression. Preload compresses a spring before the suspension carries its normal operating load.
Which damper setting resists suspension compression?
A Rebound damping
B Spring preload
C Compression damping
D Toe adjustment
Answer: C. Compression damping. Compression damping controls the rate at which the suspension compresses.
Which damper setting controls extension after a bump?
A Compression damping
B Camber adjustment
C Spring preload
D Rebound damping
Answer: D. Rebound damping. Rebound damping controls the suspension as it extends after compression.
What happens inside a hydraulic damper during movement?
A Air leaves the tire
B Fuel enters a chamber
C Grease heats a bearing
D Oil passes through valves
Answer: D. Oil passes through valves. Piston movement forces oil through calibrated passages and valves to create damping resistance.
Where is working fluid held in a twin-tube damper?
A One sealed gas cell
B A leaf stack
C Inner and outer tubes
D The wheel hub
Answer: C. Inner and outer tubes. Twin-tube dampers use an inner working tube and an outer reserve tube.
What is a common role of nitrogen in a damper?
A Reduce fluid aeration
B Increase spring length
C Raise wheel rate
D Set ride height
Answer: A. Reduce fluid aeration. Gas pressure helps suppress cavitation and foaming of damper fluid.
Motion ratio compares spring movement with what?
A Body paint thickness
B Tire tread depth
C Wheel movement
D Brake-pedal travel
Answer: C. Wheel movement. Motion ratio relates spring displacement to wheel displacement at the suspension.
Wheel rate describes effective stiffness at which point?
A The damper seal
B The steering wheel
C The wheel
D The chassis roof
Answer: C. The wheel. Wheel rate is the suspension’s effective spring stiffness measured at the wheel.
Which arm mainly guides a trailing-arm wheel?
A Transverse steering rack
B Upper spring perch
C Brake pressure valve
D Longitudinal pivoting arm
Answer: D. Longitudinal pivoting arm. A trailing arm pivots from the body and locates the wheel mainly in the fore-aft direction.
A torsion-beam axle is usually classified as what?
A Semi-independent suspension
B Rigid live axle
C Double-wishbone suspension
D Air suspension
Answer: A. Semi-independent suspension. A torsion beam allows some relative wheel motion while coupling the two sides.
What does a self-leveling air suspension adjust?
A Tire tread pattern
B Brake rotor size
C Air spring pressure
D Steering ratio
Answer: C. Air spring pressure. Changing air-spring pressure can restore a target ride height as load changes.
Which sensor can help an automatic leveling system detect height?
A Knock sensor
B Ride-height sensor
C Oxygen sensor
D Oil-pressure switch
Answer: B. Ride-height sensor. Ride-height sensors measure body position relative to the axle or wheel assembly.
A broken spring most directly changes what?
A Vehicle ride height
B Brake-pad friction
C Engine compression
D Wheelbase design
Answer: A. Vehicle ride height. Loss of spring support can lower one corner and alter the vehicle’s ride height.
What can a worn damper cause after a road bump?
A Higher fuel octane
B Repeated body bouncing
C More tire tread
D Longer wheelbase
Answer: B. Repeated body bouncing. Reduced damping lets the spring oscillate for longer after a disturbance.
Why can excessive unsprung mass harm road holding?
A It raises engine power
B It follows bumps less readily
C It shortens braking distance
D It reduces tire load
Answer: B. It follows bumps less readily. Greater unsprung mass is harder for the tire and suspension to control over rapid road changes.
Which component connects an anti-roll bar to a suspension arm?
A Brake hose
B Tie rod
C Propeller shaft
D Stabilizer link
Answer: D. Stabilizer link. A stabilizer link transfers force between the bar and a suspension arm or strut.
What may a loose stabilizer link produce?
A Rattling over bumps
B Steering fluid foam
C Engine misfire
D Brake pedal sinking
Answer: A. Rattling over bumps. A worn or loose link can make a knocking or rattling noise over uneven roads.
What does suspension droop mean?
A Spring is preloaded
B Wheel moves downward
C Body rolls inward
D Damper locks closed
Answer: B. Wheel moves downward. Droop is the suspension’s extension range as a wheel moves downward relative to the body.
Which device cushions full extension travel?
A Jounce bumper
B Anti-roll bar
C Wheel bearing
D Rebound stop
Answer: D. Rebound stop. A rebound stop limits extension and reduces harsh impact at full droop.
A strut often carries which additional load?
A Fuel-system pressure
B Brake-fluid pressure
C Structural side load
D Engine torque
Answer: C. Structural side load. A suspension strut commonly serves as a structural locating member as well as a damper.
Which suspension spring can change pressure for ride-height control?
A Air spring
B Leaf spring
C Coil spring
D Torsion bar
Answer: A. Air spring. An air spring supports load with compressed air and can be adjusted for ride height.
What is the usual effect of adding load to a fixed-rate spring?
A More spring compression
B Less sprung mass
C More tire diameter
D Less damper travel
Answer: A. More spring compression. With a fixed rate, additional load compresses the spring until a new equilibrium is reached.
Which part absorbs impact near full compression?
A Rebound stop
B Jounce bumper
C Wheel bearing
D Steering knuckle
Answer: B. Jounce bumper. A jounce bumper cushions the suspension near its maximum compression position.