Difficulty: Easy & Basic
What is a main purpose of vehicle suspension?
A Increase engine power
B Cool the brakes
C Set fuel pressure
D Maintain tire contact
Answer: D. Maintain tire contact. Suspension supports the vehicle while helping its tires follow the road and maintain contact.
Which parts make up sprung mass?
A Wheels and tires
B Brake discs only
C Body and chassis
D Road surface
Answer: C. Body and chassis. Sprung mass is the vehicle portion supported by its suspension springs, including the body and chassis.
What is unsprung mass?
A Passenger compartment
B Parts below the springs
C Fuel inside tank
D Body above mounts
Answer: B. Parts below the springs. Wheels, tires, and much of the axle or hub assembly move with the road relative to the springs.
What does a suspension spring mainly do?
A Dissipate all heat
B Control engine speed
C Support load elastically
D Measure wheel angle
Answer: C. Support load elastically. The spring supports vehicle load and deflects to absorb road-induced movement.
Why is a damper fitted with a spring?
A Increase spring length
B Raise tire pressure
C Reduce wheelbase
D Control spring oscillation
Answer: D. Control spring oscillation. A damper dissipates motion energy so the spring does not keep bouncing after a disturbance.
How does a coil spring support load?
A Twisting a leaf pack
B Axial compression or extension
C Hydraulic pressure alone
D Rotating a wheel hub
Answer: B. Axial compression or extension. A helical coil spring deflects mainly along its axis under suspension load.
Which spring is commonly made from stacked leaves?
A Leaf spring
B Coil spring
C Air spring
D Torsion bar
Answer: A. Leaf spring. A leaf spring uses curved, stacked steel leaves to provide elastic support.
A torsion bar stores energy through what?
A Oil compression
B Elastic twisting
C Leaf sliding
D Gas expansion
Answer: B. Elastic twisting. A torsion bar works as a spring by twisting elastically under applied torque.
What does a jounce bumper limit?
A Steering-wheel rotation
B Brake-pedal movement
C Engine vibration
D Excessive compression travel
Answer: D. Excessive compression travel. A jounce bumper cushions and limits suspension movement near full compression.
Wheel movement toward the vehicle body is called what?
A Jounce
B Rebound
C Toe
D Caster
Answer: A. Jounce. Jounce describes suspension compression as a wheel moves upward relative to the body.
Which term describes suspension extension after compression?
A Jounce
B Camber
C Rebound
D Scrub
Answer: C. Rebound. Rebound is the suspension’s extension movement as the wheel moves away from the body.
What characterizes independent suspension?
A Both wheels share one axle
B Each wheel moves separately
C Only rear wheels steer
D Springs are absent
Answer: B. Each wheel moves separately. Independent layouts allow one wheel’s movement to have less direct effect on the opposite wheel.
A solid axle linking both wheels is typical of which layout?
A Independent suspension
B MacPherson strut
C Trailing arm
D Dependent suspension
Answer: D. Dependent suspension. A dependent suspension mechanically links the left and right wheels through a rigid axle.
Which assembly combines a damper and structural support?
A Leaf pack
B Track rod
C MacPherson strut
D Wheel bearing
Answer: C. MacPherson strut. A MacPherson strut combines a shock absorber with a structural suspension member.
What do upper and lower arms form in a double-wishbone layout?
A Brake fluid lines
B Spring seats only
C Wheel locating links
D Steering gears
Answer: C. Wheel locating links. The two control arms guide wheel movement and help define suspension geometry.
Which component can reduce body roll in corners?
A Bump stop
B Anti-roll bar
C Wheel bearing
D Brake caliper
Answer: B. Anti-roll bar. An anti-roll bar links suspension sides and resists unequal wheel movement during body roll.
What connects a wheel assembly to the vehicle structure?
A Control arm
B Fuel rail
C Brake master cylinder
D Propeller shaft
Answer: A. Control arm. Control arms guide wheel motion and transfer suspension forces to the chassis or body.
Which joint allows control-arm pivoting in several directions?
A Ball joint
B Oil seal
C Wheel nut
D Brake pad
Answer: A. Ball joint. A ball joint permits angular movement between the control arm and steering knuckle.
Why are rubber bushings used at pivots?
A Isolate vibration and noise
B Increase tire diameter
C Store brake fluid
D Set engine timing
Answer: A. Isolate vibration and noise. Compliant bushings allow controlled movement while reducing noise and vibration transfer.
How does a hydraulic shock absorber dissipate motion?
A Compressing the tire
B Twisting the axle
C Heating brake pads
D Forcing oil through valves
Answer: D. Forcing oil through valves. Restricted oil flow through internal valves converts suspension motion into heat.
What can gas charging help prevent inside a damper?
A Spring sag
B Tire slip
C Wheel imbalance
D Oil foaming
Answer: D. Oil foaming. Pressurized gas helps limit aeration and foaming of damper oil during operation.
Suspension travel is the wheel’s movement between which limits?
A Compression and extension limits
B Left and right turns
C Front and rear axles
D Brake and throttle
Answer: A. Compression and extension limits. Travel is the available movement from the compression limit to the extension limit.
Which measurement describes body height above the road?
A Spring rate
B Wheel rate
C Ride height
D Track width
Answer: C. Ride height. Ride height is the vehicle body’s position relative to the road or wheel center.
What can visible oil on a damper body indicate?
A Correct spring preload
B Damper leakage
C Low tire tread
D Bent steering wheel
Answer: B. Damper leakage. Oil escaping from a shock absorber can indicate a failed seal and reduced damping.
Why should suspension keep a tire following a rough road?
A Preserve tire contact
B Increase exhaust flow
C Reduce wheelbase
D Change fuel mixture
Answer: A. Preserve tire contact. Maintaining tire contact supports braking, cornering, and traction over uneven surfaces.