A 40 N/mm spring has a 0.75 motion ratio. What is its wheel rate?
A 30 N/mm
B 40 N/mm
C 53.3 N/mm
D 22.5 N/mm
Answer: D. 22.5 N/mm. With motion ratio defined as spring travel divided by wheel travel, wheel rate is 40 × 0.75² = 22.5 N/mm.
For a quarter-car spring, what raises body natural frequency?
A Higher spring stiffness
B Greater sprung mass
C Lower tire pressure
D Longer wheelbase
Answer: A. Higher spring stiffness. Natural frequency varies with the square root of stiffness divided by sprung mass.
A damper’s viscous force mainly depends on what?
A Piston velocity
B Spring preload
C Wheelbase
D Tire width
Answer: A. Piston velocity. In a linear viscous model, damping force is proportional to relative damper velocity.
What does damping ratio compare?
A Actual to critical damping
B Spring rate to tire width
C Wheel load to wheelbase
D Damper stroke to ride height
Answer: A. Actual to critical damping. Damping ratio is actual damping divided by critical damping for the modeled system.
What does critical damping achieve in a simple model?
A Fastest return without oscillation
B Largest repeated oscillations
C Zero spring force
D Maximum wheel travel
Answer: A. Fastest return without oscillation. Critical damping returns a system to equilibrium quickly without oscillating in the ideal second-order model.
How does a damper remove energy from suspension motion?
A Stores it in tire air
B Dissipates it as heat
C Returns it to fuel
D Converts it to steering torque
Answer: B. Dissipates it as heat. Hydraulic restriction converts mechanical motion energy into heat in the damper fluid and body.
Increasing front roll stiffness often shifts handling toward what?
A More oversteer
B Less tire load
C More understeer
D Lower ride height
Answer: C. More understeer. With other factors held similar, more front elastic load transfer can reduce front-axle lateral grip because tires are load-sensitive.
What does the suspension roll center represent?
A Spring’s free length
B Damper pressure point
C Instantaneous lateral pivot
D Wheel’s steering axis
Answer: C. Instantaneous lateral pivot. The roll center is a geometric reference point about which the sprung body tends to roll relative to the axle.
Why can a high roll center create jacking forces?
A Springs lose preload
B Dampers stop flowing
C Lateral forces act through links
D Tires gain diameter
Answer: C. Lateral forces act through links. Suspension geometry can transmit lateral force components through links and move the body vertically.
What does anti-dive geometry reduce during braking?
A Total steady load transfer
B Brake temperature
C Tire slip angle
D Body pitch motion
Answer: D. Body pitch motion. Anti-dive geometry routes some braking force through suspension links, reducing pitch motion without eliminating load transfer.
Anti-squat geometry mainly counters what?
A Front dive under braking
B Body roll in corners
C Wheel hop at rebound
D Rear compression under drive
Answer: D. Rear compression under drive. Anti-squat geometry uses driveline and link forces to oppose rear suspension compression during acceleration.
Which geometry can provide negative camber gain in bump?
A Longer lower arm only
B Short upper control arm
C Rigid axle link
D Soft damper setting
Answer: B. Short upper control arm. A shorter upper arm in a double-wishbone layout moves the top of the wheel inward as the suspension compresses.
What is a major kinematic benefit of double wishbones?
A No damper is required
B Both wheels must move together
C Camber curve can be tuned
D Ride height stays fixed
Answer: C. Camber curve can be tuned. Arm lengths and pivot positions let designers shape camber change through suspension travel.
A progressive spring has what characteristic?
A Rate stays exactly constant
B Rate falls to zero
C Only rebound force
D Rate rises with compression
Answer: D. Rate rises with compression. A progressive spring provides increasing force per added deflection as it compresses.
What can close-wound coils do in a progressive spring?
A Reduce wheelbase
B Touch to raise effective rate
C Lock the steering rack
D Vent damper oil
Answer: B. Touch to raise effective rate. As closely spaced coils meet, the active spring length falls and the effective rate increases.
In damper terminology, high-speed valving refers to what?
A Vehicle road speed
B Engine speed
C Damper-shaft velocity
D Wheel rotation rate
Answer: C. Damper-shaft velocity. High-speed damping describes rapid damper-piston movement, not the vehicle’s travel speed.
What does position-sensitive damping respond to?
A Fuel level
B Damper stroke position
C Steering angle
D Tire temperature
Answer: B. Damper stroke position. Position-sensitive designs change damping near selected points in the damper stroke.
How does a floating piston help a monotube damper?
A Sets spring preload
B Changes wheel alignment
C Controls tire pressure
D Separates gas and oil
Answer: D. Separates gas and oil. A floating separator piston keeps the pressurized gas apart from the working oil.
Why may severe damping cycles aerate oil more readily in some twin-tube designs?
A Higher spring rate
B Lower gas separation pressure
C Longer control arms
D Smaller wheel offset
Answer: B. Lower gas separation pressure. Some twin-tube designs have less pressurized gas separation than monotube designs, increasing aeration risk under severe use.
Which suspension movement changes wheel camber in bump?
A Control-arm arc motion
B Brake-pedal movement
C Steering-column collapse
D Engine torque reaction
Answer: A. Control-arm arc motion. Control-arm pivots move the wheel through arcs that change camber as the suspension compresses.
What does a suspension toe curve plot?
A Spring force against time
B Damper heat against speed
C Ride height against fuel
D Toe angle against wheel travel
Answer: D. Toe angle against wheel travel. A toe curve shows how wheel toe changes as suspension moves through bump and rebound.
Why can a compliant bushing alter suspension geometry under load?
A It deflects under force
B It changes tire size
C It raises damper pressure
D It stiffens the chassis
Answer: A. It deflects under force. Bushing deformation changes pivot locations slightly and can shift wheel alignment under load.
Where does an anti-roll bar resist body-roll motion?
A Between engine and gearbox
B Between front and rear brakes
C Between left and right wheels
D Inside the tire tread
Answer: C. Between left and right wheels. The bar twists when the two connected suspension sides move by different amounts.
Why does a heavier unsprung assembly challenge a damper?
A It lowers sprung mass
B It needs more control force
C It reduces wheel travel
D It eliminates tire deflection
Answer: B. It needs more control force. More unsprung mass requires greater force to control its motion over road disturbances.
Which model isolates one wheel and body corner?
A Full-vehicle model
B Quarter-car model
C Rigid-body model
D Beam model
Answer: B. Quarter-car model. A quarter-car model represents one wheel station and a portion of the sprung body.