A truss member carries an intermediate load between joints. The ideal truss assumption is…
A Still exact always
B No longer exact
C A rigid-body rule
D A support condition
Answer: B. No longer exact. Ideal truss members carry axial force when loads and joints act at member ends; intermediate loading causes bending.
The force method enforces compatibility by solving for…
A Only joint displacements
B Redundant forces
C Element colors
D Load combinations only
Answer: B. Redundant forces. The force method treats redundants as unknowns and enforces compatible deformations.
Linear elastic superposition is valid when…
A Response remains linear
B Material yields significantly
C Geometry changes greatly
D Supports slide freely
Answer: A. Response remains linear. Superposition requires linear response and unchanged boundary conditions.
P-delta effects arise from…
A Shear acting on area
B Thermal strain only
C Axial load acting on deflection
D Uniform settlement only
Answer: C. Axial load acting on deflection. Axial force acting through a displaced configuration creates additional moment.
Geometric nonlinearity means…
A Equilibrium uses deformed geometry
B Material is always plastic
C Loads are absent
D Support reactions vanish
Answer: A. Equilibrium uses deformed geometry. Geometric nonlinear analysis accounts for changes in geometry during deformation.
A conservative linear structural stiffness matrix is usually…
A Symmetric
B Always diagonal
C Always singular
D Antisymmetric
Answer: A. Symmetric. For standard elastic conservative systems, reciprocal work leads to a symmetric stiffness matrix.
A two-dimensional truss joint has…
A Three rotations
B One translation only
C Two translational DOFs
D Six rotations
Answer: C. Two translational DOFs. A planar truss joint has horizontal and vertical displacement degrees of freedom.
A two-dimensional frame node commonly has…
A Three DOFs
B One axial DOF
C Two rotations
D Six translations
Answer: A. Three DOFs. A plane-frame node has horizontal and vertical translations plus in-plane rotation.
A plane beam node commonly has…
A Deflection and rotation
B Three translations
C Only axial motion
D Six rotations
Answer: A. Deflection and rotation. An Euler-Bernoulli beam node has transverse displacement and rotation degrees of freedom.
A 2D truss element local stiffness represents…
A Bending and torsion
B Axial deformation
C Shear deformation only
D Thermal conduction
Answer: B. Axial deformation. A conventional pin-jointed truss element resists axial extension and compression.
Global stiffness assembly uses…
A Only member colors
B Survey bearings
C Concrete strength
D Element connectivity
Answer: D. Element connectivity. Element stiffness terms are assembled into global degrees of freedom using connectivity.
Fixed support conditions are imposed by…
A Changing material density
B Restraining selected DOFs
C Removing every load
D Doubling all spans
Answer: B. Restraining selected DOFs. Boundary conditions prescribe or restrain the relevant displacement components.
A singular global stiffness matrix can indicate…
A Perfect fixity
B Zero load only
C High material strength
D An unstable mechanism
Answer: D. An unstable mechanism. A mechanism or missing restraint can make the global stiffness matrix singular.
Rigid-body modes represent…
A Local material yielding
B A fixed boundary
C Motion without member strain
D Stress concentration
Answer: C. Motion without member strain. Rigid-body motion changes position but does not deform the structure.
For an indeterminate structure, a moving-load influence line may be…
A Always one straight line
B Always zero
C A material stress curve
D Curved between supports
Answer: D. Curved between supports. Compatibility makes influence lines for indeterminate structures generally nonlinear in segments.
Muller-Breslau’s principle releases the restraint for the…
A Largest applied load
B Lowest modulus
C Response being studied
D Longest member
Answer: C. Response being studied. The influence-line shape follows the deflected form after releasing the response restraint.
In moment distribution, balancing an unbalanced joint moment uses…
A Column areas only
B Member distribution factors
C Support settlement values
D Load positions only
Answer: B. Member distribution factors. Joint moments are distributed by member stiffness proportions.
An ideal internal hinge transmits…
A Moment but no force
B No force or moment
C Only torsion
D Force but no moment
Answer: D. Force but no moment. A hinge can transfer forces while allowing relative rotation and zero moment at the hinge.
A three-hinged arch can be analyzed by…
A Equilibrium and hinge condition
B Compatibility alone
C Finite elements only
D Moment distribution only
Answer: A. Equilibrium and hinge condition. The crown-hinge moment condition plus equilibrium makes a three-hinged arch determinate.
A funicular cable under matching load carries mainly…
A Bending moment
B Compression
C Shear only
D Axial tension
Answer: D. Axial tension. A cable assumes a funicular shape and carries axial tension for the matching load pattern.
A parabolic cable shape corresponds to load uniform per…
A Cable length
B Vertical height
C Horizontal span
D Support rotation
Answer: C. Horizontal span. A parabola is the funicular shape for uniform load per horizontal projection.
Support settlement can induce member forces in…
A Indeterminate structures
B Every determinate truss equally
C Only free cables
D No elastic structure
Answer: A. Indeterminate structures. Redundant restraints can convert imposed settlement into internal forces in indeterminate systems.
Uniform heating of a free determinate bar mainly causes…
A Support moment
B Buckling load
C Free expansion
D Shear force
Answer: C. Free expansion. Without restraint, uniform heating produces expansion but no thermal stress in the ideal bar.
A structural analysis software result depends critically on…
A Screen resolution
B Model and boundary conditions
C File name length
D Color theme
Answer: B. Model and boundary conditions. Incorrect connectivity, supports or loads can make computed results misleading.
A frame with sidesway has…
A Only vertical deflection
B No axial force
C No bending moment
D Lateral joint displacement
Answer: D. Lateral joint displacement. Sidesway is lateral translation of frame joints under load or asymmetry.