Difficulty: Hard
An 800 kg aircraft section has arm 1.8 m; a 200 kg load is at 3.0 m. Find combined CG arm.
A 1.92 m
B 2.04 m
C 2.16 m
D 2.40 m
Answer: B. 2.04 m. Combined CG is total moment divided by total mass: (800×1.8 + 200×3.0)/1,000 = 2.04 m.
A tail applies 900 N downward, 4 m aft of CG. What nose-up moment results?
A 3,600 N·m
B 900 N·m
C 1,800 N·m
D 4,500 N·m
Answer: A. 3,600 N·m. Moment equals force times perpendicular arm: 900 × 4 = 3,600 N·m.
A rudder produces 250 N side force at a 5.2 m arm. What yaw moment is produced?
A 650 N·m
B 1,000 N·m
C 2,600 N·m
D 1,300 N·m
Answer: D. 1,300 N·m. Yawing moment equals side force multiplied by its arm: 250 × 5.2 = 1,300 N·m.
CG moves from 38% to 32% MAC while neutral point stays at 50%. How does static margin change?
A Falls six points
B Rises twelve points
C Rises six points
D Stays unchanged
Answer: C. Rises six points. Static margin increases from 12% to 18% MAC, a rise of six percentage points.
To counter an unwanted nose-up moment, which conventional elevator motion creates a nose-down moment?
A Trailing edge up
B Rudder left
C Ailerons down
D Trailing edge down
Answer: D. Trailing edge down. A conventional elevator deflected trailing-edge down increases tail lift, producing a nose-down pitching moment.
For a fixed deflection and geometry, dynamic pressure doubles. What happens roughly to aerodynamic hinge force?
A It halves
B It doubles
C It is unchanged
D It becomes zero
Answer: B. It doubles. Aerodynamic force and hinge moment scale approximately with dynamic pressure at the same coefficient.
A flexible wing twists so an aileron deflection eventually reverses rolling effect. What is this called?
A Control reversal
B Dutch roll
C Spiral stability
D Trim drag
Answer: A. Control reversal. Aeroelastic torsion can reduce or reverse the intended control effect at high dynamic pressure.
During sideslip, positive dihedral effect generally creates what rolling response?
A Pitch divergence
B More adverse yaw
C Restoring roll
D No rolling moment
Answer: C. Restoring roll. Positive dihedral effect produces a rolling moment tending to reduce the sideslip.
Why can aileron roll-in yaw opposite the commanded turn?
A Tail lift
B Fuel shift
C Static margin
D Unequal drag
Answer: D. Unequal drag. Different drag from the two ailerons creates adverse yaw opposite the roll direction.
At a forward CG limit, what handling demand may become critical during flare?
A Elevator authority
B Rudder trim
C Spoiler travel
D Aileron differential
Answer: A. Elevator authority. A forward CG increases the nose-up pitching demand and can approach elevator authority limits.
Why can an aft CG complicate stall recovery?
A Higher brake energy
B Less nose-down stability
C More dihedral effect
D Lower thrust
Answer: B. Less nose-down stability. An aft CG reduces longitudinal stability and the natural nose-down recovery tendency.
In sideslip, a stable vertical tail tends to do what?
A Raise both wings
B Lower cabin altitude
C Align nose with wind
D Reduce engine torque
Answer: C. Align nose with wind. The fin produces a weathercocking moment that tends to align the nose with the relative wind.
Which feedback signal is commonly used by a yaw damper?
A Fuel flow
B Cabin pressure
C Brake temperature
D Yaw rate
Answer: D. Yaw rate. Yaw-rate feedback allows the damper to oppose oscillatory yaw motion.
Which surfaces combine pitch and roll control on a tailless aircraft?
A Elevons
B Ruddervators
C Flaperons
D Spoilerons
Answer: A. Elevons. Elevons combine elevator and aileron functions on tailless aircraft.
Which controls combine rudder and elevator functions on some V-tail designs?
A Elevons
B Ruddervators
C Flaperons
D Spoilers
Answer: B. Ruddervators. Ruddervators mix pitch and yaw commands for the two V-tail surfaces.
Spoilerons are primarily used to assist which motion?
A Pitch
B Yaw
C Roll
D Heave
Answer: C. Roll. Spoilerons use asymmetric spoiler deployment to assist roll control.
A control surface mass balance is placed ahead of its hinge mainly to reduce what?
A Adverse yaw
B Pitch trim
C Tail volume
D Flutter tendency
Answer: D. Flutter tendency. Mass balance reduces inertial moments that can excite control-surface flutter.
A 120 N aerodynamic load acts 0.15 m from a hinge. What hinge moment results?
A 18 N·m
B 8 N·m
C 36 N·m
D 80 N·m
Answer: A. 18 N·m. Hinge moment is load times perpendicular arm: 120 × 0.15 = 18 N·m.
Why do fully powered controls need an artificial feel system?
A Increase hydraulic pressure
B Provide pilot force cues
C Change neutral point
D Reduce wing loading
Answer: B. Provide pilot force cues. Artificial feel restores useful force cues when aerodynamic loads are not directly felt by the pilot.
Near a stall, why can aileron control lose effectiveness?
A Higher static margin
B Lower cabin pressure
C Separated airflow
D More tail volume
Answer: C. Separated airflow. Flow separation over the wing can reduce the aileron’s ability to change local lift.
Why are mechanical stops installed in a flight-control system?
A Increase tail force
B Reduce pitch damping
C Set the neutral point
D Limit control travel
Answer: D. Limit control travel. Mechanical stops prevent overtravel and protect control surfaces and linkages.
What is the purpose of a horn balance on a control surface?
A Reduce hinge moment
B Increase wing loading
C Shift the neutral point
D Damp Dutch roll
Answer: A. Reduce hinge moment. A horn balance adds aerodynamic area ahead of the hinge to reduce hinge moment.
A stabilizer trim command changes which quantity directly?
A Engine thrust
B Tail aerodynamic balance
C Wing sweep
D Landing-gear track
Answer: B. Tail aerodynamic balance. Stabilizer trim changes tail incidence or trim setting to rebalance pitching moments.
A statically restoring aircraft has oscillations that grow after each cycle. What is the dynamic result?
A Dynamically neutral
B Fully damped
C Dynamically unstable
D Control locked
Answer: C. Dynamically unstable. A restoring initial response can coexist with negative dynamic stability if oscillations grow over time.
Within a linear control range, 30° aileron deflection produces 1,200 N·m rolling moment. What does 15° produce approximately?
A 600 N·m
B 300 N·m
C 900 N·m
D 2,400 N·m
Answer: A. 600 N·m. If response is approximately linear, halving deflection halves the rolling moment.