Difficulty: Easy & Basic
During a right roll command, which aileron typically rises?
A Right aileron
B Left aileron
C Both ailerons
D Neither aileron
Answer: A. Right aileron. For a right roll, the right aileron deflects upward and the left generally deflects downward.
What does a differential aileron arrangement help reduce?
A Pitch trim
B Dutch roll
C Stall speed
D Adverse yaw
Answer: D. Adverse yaw. Differential motion can reduce drag imbalance between rising and descending ailerons.
Why may rudder be applied during aileron roll-in?
A Increase cabin pressure
B Coordinate the turn
C Lower stall speed
D Extend the gear
Answer: B. Coordinate the turn. Rudder helps counter adverse yaw and coordinate the aircraft through a turn.
What do spoilers do when deployed in flight?
A Increase lift
B Move the CG
C Reduce lift
D Change tail volume
Answer: C. Reduce lift. Spoilers disrupt airflow over the wing, reducing lift and usually increasing drag.
What is a common aerodynamic effect of flap extension?
A Less lift and drag
B More stability only
C Less wing area
D More lift and drag
Answer: D. More lift and drag. Flaps increase camber and lift, while their deflection also increases drag.
What does an elevator trim tab change?
A Wing sweep
B Rudder area
C Elevator hinge moment
D Thrust line
Answer: C. Elevator hinge moment. A trim tab alters aerodynamic force on the elevator to reduce sustained control force.
Pulling a conventional control yoke aft commands what?
A Nose-up pitch
B Nose-down pitch
C Right yaw
D Left roll
Answer: A. Nose-up pitch. Aft control input commands the elevator to produce a nose-up pitching response.
Which surface helps the aircraft yaw around its vertical axis?
A Elevator
B Rudder
C Aileron
D Flap
Answer: B. Rudder. Rudder deflection creates a yawing moment about the vertical axis.
What is adverse yaw during roll entry?
A Nose rises with roll
B Aircraft descends vertically
C Nose yaws opposite roll
D Rudder reverses pitch
Answer: C. Nose yaws opposite roll. Aileron drag differences can yaw the nose opposite the commanded roll direction.
Which design feature can contribute to directional stability?
A Vertical fin
B Wing flap
C Landing gear
D Horizontal trim tab
Answer: A. Vertical fin. The vertical fin produces a restoring yawing moment in sideslip.
Which feature can improve lateral stability besides dihedral?
A Aft CG
B Large elevator
C Shorter fuselage
D Wing sweepback
Answer: D. Wing sweepback. Sweepback can create a restoring rolling tendency when a sideslip develops.
Why are flight-control locks installed on parked aircraft?
A Reduce engine noise
B Protect against gusts
C Balance fuel
D Cool the brakes
Answer: B. Protect against gusts. Control locks restrain surfaces against wind loads while the aircraft is parked.
What does a servo tab primarily do?
A Assist control movement
B Increase cabin pressure
C Measure yaw rate
D Change fuel flow
Answer: A. Assist control movement. A servo tab uses aerodynamic force to help move a larger control surface.
What does a spring tab help reduce at high speed?
A Wing loading
B Static margin
C Pilot control force
D Yaw damping
Answer: C. Pilot control force. A spring tab assists control movement as aerodynamic hinge forces increase.
Why are control surfaces mass-balanced?
A Increase lift coefficient
B Improve fuel transfer
C Lower tire wear
D Reduce flutter risk
Answer: D. Reduce flutter risk. Mass balance helps limit inertial coupling that can contribute to control-surface flutter.
In a fly-by-wire system, pilot input is sent first to what?
A Hydraulic reservoir
B Flight-control computers
C Fuel selector
D Gear uplock
Answer: B. Flight-control computers. Fly-by-wire systems transmit pilot commands to computers that calculate actuator commands.
What do flaperons combine?
A Rudder and elevator
B Spoiler and trim
C Flap and aileron roles
D Brake and steering
Answer: C. Flap and aileron roles. Flaperons serve as both trailing-edge flap devices and roll-control surfaces.
Which control surface can rapidly dump wing lift after touchdown?
A Spoiler
B Rudder
C Elevator
D Trim tab
Answer: A. Spoiler. Ground spoilers reduce lift so more aircraft weight transfers to the wheels for braking.
When CG moves forward, what commonly happens to elevator control demand?
A Less tail authority needed
B Greater nose-up force
C Rudder force doubles
D Aileron trim disappears
Answer: B. Greater nose-up force. A forward CG increases the balancing nose-up tail force and can increase elevator control demand.
An aft CG within limits generally does what to longitudinal stability?
A Increases tail volume
B Eliminates pitch control
C Raises the neutral point
D Reduces stability margin
Answer: D. Reduces stability margin. Moving CG aft reduces its distance ahead of the neutral point.
What does control harmony mean?
A Equal fuel quantity
B Identical wing loading
C Balanced control forces
D Matching brake temperature
Answer: C. Balanced control forces. Control harmony refers to appropriate relative forces and responses across the primary controls.
Why can a high-mounted wing with dihedral be laterally stable?
A Sideslip creates restoring roll
B Elevator force vanishes
C Rudder becomes neutral
D CG moves forward
Answer: A. Sideslip creates restoring roll. Dihedral and related geometry can generate a restoring rolling moment during sideslip.
Which control surface can create a nose-down pitch moment when deflected?
A Aileron
B Elevator
C Rudder
D Spoiler only
Answer: B. Elevator. Elevator deflection changes tail force and creates a pitching moment.
What is the main role of a rudder trim control?
A Change wing incidence
B Set cabin altitude
C Adjust brake pressure
D Reduce steady rudder force
Answer: D. Reduce steady rudder force. Rudder trim offsets sustained yawing tendencies without holding constant pedal pressure.
A stability augmentation actuator adds what to pilot commands?
A Fuel flow
B Cabin cooling
C Automatic corrections
D Wheel braking
Answer: C. Automatic corrections. Stability augmentation adds sensor-based control inputs to improve aircraft response.