Difficulty: Easy & Basic
After a small disturbance, the aircraft initially tends to return to its original state. What property is shown?
A Negative stability
B Positive static stability
C Neutral stability
D Dynamic divergence
Answer: B. Positive static stability. Positive static stability is the initial tendency to return toward the original equilibrium.
What does dynamic stability describe?
A Response over time
B Initial turn direction
C Control force only
D Aircraft loading
Answer: A. Response over time. Dynamic stability describes how motion changes over time after a disturbance.
Static stability concerns which response?
A Long-term oscillations
B Fuel balance
C Control-surface wear
D Initial tendency
Answer: D. Initial tendency. Static stability is the initial response direction after equilibrium is disturbed.
Rotation about the aircraft longitudinal axis is called what?
A Pitch
B Yaw
C Roll
D Heave
Answer: C. Roll. The longitudinal axis runs nose to tail; rotation around it is roll.
Which axis runs from wingtip to wingtip?
A Lateral
B Longitudinal
C Vertical
D Normal
Answer: A. Lateral. The lateral axis extends from wingtip to wingtip, and rotation around it is pitch.
Rotation about the vertical axis is called what?
A Roll
B Pitch
C Sideslip
D Yaw
Answer: D. Yaw. Yaw is rotation around the vertical axis through the aircraft’s center of gravity.
Which primary control surface commands roll?
A Elevator
B Ailerons
C Rudder
D Flaps
Answer: B. Ailerons. Ailerons create differential lift and roll the aircraft about its longitudinal axis.
Which primary surface commands pitch?
A Ailerons
B Rudder
C Elevator
D Spoilers
Answer: C. Elevator. The elevator changes tail force and controls pitch about the lateral axis.
Which primary surface commands yaw?
A Elevator
B Ailerons
C Flaps
D Rudder
Answer: D. Rudder. The rudder controls yaw about the vertical axis.
Which tail surface mainly supports longitudinal stability?
A Horizontal stabilizer
B Vertical stabilizer
C Winglet
D Spoiler
Answer: A. Horizontal stabilizer. The horizontal tail contributes to pitch stability and control.
Which surface mainly contributes to directional stability?
A Horizontal stabilizer
B Flaperon
C Vertical stabilizer
D Elevator
Answer: C. Vertical stabilizer. The vertical tail supplies a restoring yawing tendency in sideslip.
What does the aircraft center of gravity represent?
A Center of lift
B Average weight location
C Thrust application point
D Wing aerodynamic center
Answer: B. Average weight location. The center of gravity is the location at which total aircraft weight is treated as concentrated.
Within limits, moving the CG forward generally does what to longitudinal stability?
A Increases stability
B Removes elevator control
C Eliminates trim
D Reverses yaw
Answer: A. Increases stability. A forward CG generally increases longitudinal stability, within approved loading limits.
Moving the CG too far aft can cause what?
A Higher tire pressure
B More rudder area
C Lower cabin altitude
D Reduced stability
Answer: D. Reduced stability. An aft CG moves closer to the neutral point and can reduce longitudinal stability.
What is the neutral point used to assess?
A Brake energy
B Fuel flow
C Longitudinal stability
D Lateral trim
Answer: C. Longitudinal stability. The neutral point is a reference for assessing longitudinal static stability.
Static margin is the distance between which points?
A Wing and tail
B CG and neutral point
C Nose and engine
D Rudder and fin
Answer: B. CG and neutral point. Static margin compares CG location with the neutral point, usually as a chord fraction.
What does trimming an aircraft allow?
A Hands-off balance
B Higher stall speed
C More runway length
D Automatic fuel transfer
Answer: A. Hands-off balance. Trim reduces sustained control force so the aircraft can maintain the selected condition hands-off.
In steady equilibrium, what is the sum of forces and moments?
A Maximum
B Increasing
C Unrelated
D Zero
Answer: D. Zero. A steady equilibrium requires net force and net moment to be zero.
Which wing geometry can improve lateral static stability?
A Wash-in
B Dihedral
C Zero sweep
D Negative taper
Answer: B. Dihedral. Dihedral helps produce a restoring roll tendency when the aircraft sideslips.
After a disturbance, neutral static stability means the aircraft initially does what?
A Returns immediately
B Diverges rapidly
C Remains displaced
D Stops all rotation
Answer: C. Remains displaced. Neutral static stability means the initial tendency is to remain in the new condition.
Negative static stability causes the aircraft to initially do what?
A Move farther away
B Return to trim
C Remain unchanged
D Reduce airspeed
Answer: A. Move farther away. Negative static stability is an initial tendency to continue away from equilibrium.
Oscillations that gradually decrease indicate what?
A Negative static stability
B Neutral control
C Control reversal
D Positive dynamic stability
Answer: D. Positive dynamic stability. Damped oscillations decrease with time, indicating positive dynamic stability.
What is the purpose of an elevator trim tab?
A Increase wing area
B Reduce control force
C Change engine thrust
D Move the CG
Answer: B. Reduce control force. A trim tab helps balance hinge moments and reduce sustained pilot force.
What does a yaw damper primarily reduce?
A Pitch trim
B Roll rate
C Yaw oscillations
D Brake vibration
Answer: C. Yaw oscillations. A yaw damper senses yawing motion and applies rudder input to damp oscillations.
What does a stability augmentation system provide?
A Automatic stabilizing inputs
B Fuel management
C Landing gear braking
D Cabin pressurization
Answer: A. Automatic stabilizing inputs. A stability augmentation system uses sensors and actuators to add stabilizing control inputs.