Quality is the degree to which a product meets what?
A Machine capacity
B Supplier distance
C Requirements
D Production rate only
Answer: C. Requirements. Quality reflects conformance to requirements and fitness for use.
Inspection checks whether output conforms to what?
A Demand forecast
B Machine layout
C Specifications
D Inventory policy
Answer: C. Specifications. Inspection compares measured characteristics with stated requirements.
Statistical process control monitors what over time?
A Employee attendance
B Supplier ownership
C Process variation
D Product advertising
Answer: C. Process variation. SPC uses data to understand and control process variation.
A control chart signals special causes using what?
A Control limits and patterns
B Only specification limits
C A bill of materials
D Machine cycle time
Answer: A. Control limits and patterns. Control charts identify unusual process behavior beyond common-cause variation.
Process capability compares process spread with what?
A Customer count
B Production schedule
C Machine cost
D Specification width
Answer: D. Specification width. Capability indices compare process variation with engineering tolerance.
Cp measures potential capability assuming what?
A No variation
B Centered process
C Perfect measurement
D Zero defect rate
Answer: B. Centered process. Cp compares specification width with process spread, without accounting for centering.
Cpk accounts for process spread and what?
A Supplier distance
B Machine age
C Batch size only
D Centering
Answer: D. Centering. Cpk considers the nearest specification limit and process mean.
Six Sigma aims for very low what?
A Inventory turnover
B Defect rate
C Machine speed
D Work content
Answer: B. Defect rate. Six Sigma reduces process defects and variation.
A Pareto chart ranks causes by what?
A Chronological order
B Machine size
C Operator height
D Frequency or impact
Answer: D. Frequency or impact. Pareto analysis orders categories to highlight the vital few contributors.
A fishbone diagram organizes possible what?
A Root causes
B Production quantities
C Machine schedules
D Customer payments
Answer: A. Root causes. Cause-and-effect diagrams structure potential causes of a problem.
The 5 Whys method is used to find what?
A Inspection sample size
B Machine capacity
C Supplier price
D Root cause
Answer: D. Root cause. Repeatedly asking why helps trace a problem to an underlying cause.
FMEA risk priority number multiplies severity, occurrence and what?
A Cycle time
B Detection rating
C Material cost
D Defect count only
Answer: B. Detection rating. RPN = severity × occurrence × detection ratings.
Acceptance sampling decides lot disposition using what?
A Sample inspection
B Every unit inspection
C Machine downtime
D Customer survey only
Answer: A. Sample inspection. Acceptance sampling uses sample results to accept or reject a lot.
An operating-characteristic curve plots acceptance probability against what?
A Machine utilization
B Lot quality
C Cycle time
D Worker fatigue
Answer: B. Lot quality. The OC curve shows probability of lot acceptance for different defect levels.
Total quality management involves what participation?
A Organization-wide participation
B Inspectors only
C Suppliers only
D Managers only
Answer: A. Organization-wide participation. TQM engages the organization in continuous customer-focused quality improvement.
Kaizen means what in operations?
A One-time inspection
B Mass production
C Continuous improvement
D Inventory buffering
Answer: C. Continuous improvement. Kaizen is a philosophy of ongoing incremental improvement.
Poka-yoke is designed to do what?
A Increase batch size
B Delay inspection
C Prevent mistakes
D Raise inventory
Answer: C. Prevent mistakes. Poka-yoke uses error-proofing methods to prevent or immediately detect mistakes.
ISO 9001 specifies requirements for what?
A Environmental emissions only
B Product dimensions only
C Quality management system
D Machine guarding only
Answer: C. Quality management system. ISO 9001 defines requirements for a quality management system.
Gauge repeatability and reproducibility evaluates what?
A Measurement system variation
B Process capacity only
C Supplier delivery
D Machine utilization
Answer: A. Measurement system variation. Gauge R&R separates equipment repeatability and appraiser reproducibility variation.
Calibration compares a measuring instrument with what?
A Production schedule
B Work instruction
C Finished product only
D Reference standard
Answer: D. Reference standard. Calibration relates instrument readings to a recognized reference standard.
Measurement traceability links results through what?
A Supplier invoice
B Unbroken calibration chain
C Production route
D Inspection sample only
Answer: B. Unbroken calibration chain. Metrological traceability connects measurements through documented calibrations to standards.
A specification limit is set by what?
A Design requirement
B Control chart centerline
C Process average
D Machine speed
Answer: A. Design requirement. Specification limits define acceptable product characteristics from design or customer needs.
Design of experiments studies factor effects using what?
A Unstructured guesses
B Final inspection only
C Inventory counts
D Planned test combinations
Answer: D. Planned test combinations. DOE varies factors systematically to estimate main effects and interactions.
Taguchi loss function measures loss from what?
A Only defects beyond limits
B Deviation from target
C Machine downtime only
D Supplier count
Answer: B. Deviation from target. Taguchi treats deviation from target as a quality loss even within tolerance.
Corrective action removes what from a recurring problem?
A Underlying cause
B Inspection records
C Product requirements
D All process controls
Answer: A. Underlying cause. Corrective action addresses the cause to prevent recurrence.