In a steam power plant, which component raises water into high-pressure steam?
A Condenser
B Cooling tower
C Generator
D Boiler
Answer: D. Boiler. The boiler transfers heat to feedwater to produce steam.
What converts steam energy into rotating shaft power?
A Steam turbine
B Condenser
C Transformer
D Feedwater tank
Answer: A. Steam turbine. Expanding steam drives turbine blades and the generator shaft.
What is the condenserβs main role in a steam cycle?
A Burn fuel
B Raise generator voltage
C Compress combustion air
D Condense exhaust steam
Answer: D. Condense exhaust steam. It rejects heat and returns turbine exhaust to liquid water.
Which component raises condensate pressure before it returns to the boiler?
A Generator exciter
B Cooling tower fan
C Feedwater pump
D Ash collector
Answer: C. Feedwater pump. A pump moves pressurized water back into the steam generator.
An economizer recovers flue-gas heat to warm what?
A Boiler feedwater
B Generator rotor
C Coal ash
D Cooling water only
Answer: A. Boiler feedwater. Preheating feedwater reduces the heat needed in the boiler.
A superheater raises steam temperature above which condition?
A Saturation temperature
B Ambient temperature only
C Condenser pressure
D Generator frequency
Answer: A. Saturation temperature. Superheated steam has a temperature above saturation at its pressure.
A reheater returns partly expanded steam to what?
A Liquid state immediately
B Fuel storage
C Generator stator
D Higher temperature
Answer: D. Higher temperature. Reheating before later turbine stages helps limit moisture and improve cycle performance.
A cooling tower rejects condenser heat mainly to what?
A Atmosphere
B Generator rotor
C Fuel bunker
D Transmission line
Answer: A. Atmosphere. It transfers heat from circulating water to ambient air.
A coal pulverizer prepares fuel by doing what?
A Removing turbine blades
B Condensing steam
C Filtering generator oil
D Grinding coal finely
Answer: D. Grinding coal finely. Fine coal particles burn more rapidly and evenly.
What material remains after mineral matter in coal is burned?
A Pure oxygen
B Feedwater
C Ash
D Steam condensate
Answer: C. Ash. Ash handling removes noncombustible residues.
In a simple gas-turbine plant, which device compresses intake air?
A Condenser
B Economizer
C Compressor
D Generator
Answer: C. Compressor. The compressor raises air pressure before fuel combustion.
Where is fuel burned in a conventional gas-turbine cycle?
A Condenser
B Combustor
C Transformer
D Cooling pond
Answer: B. Combustor. Fuel and compressed air react in the combustion chamber.
A gas turbine extracts shaft work from what flowing medium?
A Hot combustion gas
B Liquid feedwater
C Transformer oil
D Solid ash
Answer: A. Hot combustion gas. High-temperature pressurized gas expands through turbine stages.
A combined-cycle station recovers gas-turbine exhaust heat in what?
A Pole changer
B Commutator
C Cooling fan only
D Heat-recovery steam generator
Answer: D. Heat-recovery steam generator. The HRSG produces steam for an additional steam turbine.
Why can combined-cycle generation exceed simple gas-turbine efficiency?
A Doubles grid frequency
B Uses exhaust heat
C Eliminates all fuel
D Stops compression
Answer: B. Uses exhaust heat. It converts part of otherwise wasted exhaust heat into more electric output.
Combined heat and power uses rejected heat for what?
A Changing pole count
B Charging rotor fields only
C Useful heating
D Line insulation
Answer: C. Useful heating. Cogeneration supplies process or building heat along with electricity.
What produces heat in a conventional nuclear reactor for power generation?
A Nuclear fission
B Coal combustion
C Wind motion
D Solar PV junction
Answer: A. Nuclear fission. Controlled fission releases thermal energy.
What do reactor control rods chiefly absorb?
A Steam pressure
B Neutrons
C Generator voltage
D Cooling water
Answer: B. Neutrons. Neutron absorption changes the chain-reaction rate.
In many thermal reactors, a moderator slows what?
A Turbine speed
B Steam flow
C AC frequency
D Neutrons
Answer: D. Neutrons. Slower neutrons help sustain the fission chain reaction in thermal designs.
A containment structure is a safety barrier around what?
A Transmission tower
B Coal bunker
C Reactor systems
D Cooling tower fan
Answer: C. Reactor systems. Containment helps limit release from reactor systems in abnormal conditions.
A nuclear station commonly turns its generator with what prime mover?
A Wind rotor
B Steam turbine
C Water wheel
D DC motor only
Answer: B. Steam turbine. Reactor heat is used to produce steam that drives a turbine.
Does a typical nuclear reactor directly generate AC at its fuel rods?
A No
B Yes, directly
C Only at night
D Only with solar PV
Answer: A. No. Fission provides heat; a turbine-generator converts that heat to electricity.
Burning fossil fuel releases which greenhouse gas from its carbon content?
A Helium
B Carbon dioxide
C Argon
D Neon
Answer: B. Carbon dioxide. Carbon in fuel reacts with oxygen to form CO2.
Flue-gas desulfurization chiefly targets which pollutant?
A Nitrogen gas
B Sulfur dioxide
C Water vapor
D Oxygen
Answer: B. Sulfur dioxide. Scrubbers remove much of the SO2 from combustion exhaust.
An electrostatic precipitator is used to remove what from flue gas?
A Generator frequency
B Steam pressure
C Particulates
D Shaft torque
Answer: C. Particulates. Charged dust particles are collected on electrodes.