For a dry cohesionless infinite slope with β=20° and φ=35°, its factor of safety is about:
A 0.57
B 1.37
C 1.92
D 2.57
Answer: C. 1.92. For a dry cohesionless infinite slope, factor of safety is tan φ divided by tan β. With 35° and 20°, the result is about 1.92.
In pseudostatic slope analysis, kh is horizontal acceleration divided by:
A Gravity acceleration
B Slope angle
C Soil density
D Groundwater depth
Answer: A. Gravity acceleration. The horizontal seismic coefficient kh is the assumed horizontal acceleration normalized by gravitational acceleration g.
The ordinary method of slices simplifies its calculation by neglecting:
A Pore pressure
B Slice weights
C Base resistance
D Interslice forces
Answer: D. Interslice forces. The ordinary or Fellenius method neglects forces between slices while evaluating equilibrium along a trial slip surface.
Which limit-equilibrium method satisfies both force and moment equilibrium?
A Ordinary method
B Morgenstern-Price
C Infinite-slope model
D Fellenius method
Answer: B. Morgenstern-Price. The Morgenstern-Price method accounts for interslice forces and satisfies overall force and moment equilibrium.
In finite-element strength reduction, the safety factor is the reduction multiplier when:
A Water drains
B Failure develops
C Soil dries
D Peak strain begins
Answer: B. Failure develops. The method progressively reduces soil strength parameters until the numerical model reaches failure; the reduction factor estimates the safety factor.
Across several trial slip surfaces, the critical surface usually has the:
A Highest pore pressure
B Largest radius
C Lowest safety factor
D Shallowest depth
Answer: C. Lowest safety factor. The critical trial surface is the one with the minimum calculated factor of safety under the selected analysis assumptions.
Monte Carlo slope analysis handles uncertain inputs through:
A Repeated random sampling
B One fixed estimate
C Visual inspection
D Single lab test
Answer: A. Repeated random sampling. Monte Carlo analysis repeatedly samples input values from assigned distributions and evaluates the resulting stability outcomes.
A narrow landslide with strong side confinement is where 2D analysis may miss:
A Pore-water chemistry
B Rainfall duration
C Rock color variation
D Three-dimensional effects
Answer: D. Three-dimensional effects. A narrow slide can gain important resistance from its lateral boundaries, which a two-dimensional plane-strain model cannot represent fully.
A landslide entering a reservoir can generate a fast-moving:
A Tidal bore
B River delta
C Seiche only
D Impulse wave
Answer: D. Impulse wave. Rapid displacement of water by a landslide can produce an impulse wave that travels across the reservoir.
A debris-flow basin below a steep channel is designed mainly to:
A Increase channel velocity
B Trap sediment and debris
C Raise pore pressure
D Start slope movement
Answer: B. Trap sediment and debris. Debris-flow basins provide storage for sediment and debris, reducing the amount that continues toward downstream areas.
Rainwater filling a tension crack above a slide can increase its:
A Hydrostatic driving force
B Root reinforcement
C Rock cohesion
D Drainage capacity
Answer: A. Hydrostatic driving force. Water in a tension crack exerts pressure on the back of the potentially moving mass and can add a driving force.
For similar fall heights, a smaller angle of reach generally indicates:
A Shorter travel distance
B Greater source height
C Longer relative runout
D Lower slide volume
Answer: C. Longer relative runout. The angle of reach compares vertical fall with horizontal runout; a smaller angle corresponds to greater horizontal travel relative to fall height.
Stabilizing piles should cross the slip surface and extend into:
A Loose surface debris
B The tension crack
C The moving block
D Stable underlying ground
Answer: D. Stable underlying ground. Piles can resist movement when they pass through the potential shear zone and develop support in stable material below it.
Back-analysis of a documented slope failure commonly assumes its factor of safety was near:
A One at failure
B Zero before rain
C Two after failure
D Ten during movement
Answer: A. One at failure. At the onset of failure, resisting and driving forces are approximately balanced, so the factor of safety is near one under the modeled conditions.
A debris-flow fan commonly develops where a channel:
A Enters a narrow gorge
B Opens onto flatter ground
C Cuts a steep headwall
D Meets a rock joint
Answer: B. Opens onto flatter ground. At a channel outlet, lower gradient and reduced confinement encourage debris-flow material to spread and deposit as a fan.
Why are rainfall thresholds usually calibrated to local conditions?
A Universal rock colors
B Latitude alone
C Local climate and soils
D One fixed storm type
Answer: C. Local climate and soils. Rainfall response depends on local geology, soil, antecedent moisture, and storm patterns, so thresholds need local event data.
An assumed kh of 0.15 applies a horizontal inertial force equal to:
A 15% of weight
B 1.5% of weight
C 50% of weight
D 150% of weight
Answer: A. 15% of weight. Because kh equals horizontal acceleration divided by g, 0.15g produces an inertial force of 0.15 times the mass weight.
In a drained triaxial test, shearing proceeds slowly enough for:
A All grains to dissolve
B The sample to dry
C Excess pressure to dissipate
D The confining stress vanish
Answer: C. Excess pressure to dissipate. Drained loading allows water to escape during shearing, preventing excess pore pressure from remaining in the specimen.
Anisotropic soil strength means resistance changes with the:
A Air temperature
B Soil color
C Storm duration
D Direction of shearing
Answer: D. Direction of shearing. Depositional fabric or layering can make shear resistance depend on the orientation of the failure plane.
A landslide-volume estimate needs mapped area and an estimate of:
A Average air temperature
B Mean movement depth
C Annual rainfall total
D Slope aspect only
Answer: B. Mean movement depth. A first-order volume estimate combines the plan area of the displaced mass with its representative thickness or depth.
To model a stratified landslide, field sampling should especially characterize:
A Surface colors only
B Weak layers and contacts
C Nearby tree heights
D Unrelated stream beds
Answer: B. Weak layers and contacts. Contrasts at weak layers and material contacts may control the slip surface, so they should be represented in strength testing.
A sensitivity analysis varies model inputs to identify their:
A Exact failure date
B Surface color range
C Historic names only
D Influence on stability results
Answer: D. Influence on stability results. Sensitivity analysis shows how changes in uncertain inputs affect a calculated stability measure, such as factor of safety.
In a factor-of-safety reliability model, a simulated case is counted as failure when:
A FOS is above two
B Rainfall is absent
C FOS is below one
D Slope height is zero
Answer: C. FOS is below one. Under the usual limit-equilibrium definition, a factor of safety below one means modeled driving action exceeds modeled resistance.
A rockfall catch fence energy rating is compared with the block’s:
A Impact kinetic energy
B Mineral hardness
C Surface temperature
D Annual rainfall
Answer: A. Impact kinetic energy. Catch-fence capacity is selected to withstand the impact energy expected from design rockfall blocks.
Two slides with equal vertical fall can have different runout because their:
A Map colors differ
B Names are different
C Compass bearings match
D Volume and materials differ
Answer: D. Volume and materials differ. Runout also depends on mass volume, material properties, water content, and path conditions, not just vertical fall.