A slope has shear strength of 36 kPa and driving stress of 24 kPa. Its factor of safety is:
A 0.67
B 1.0
C 2.0
D 1.5
Answer: D. 1.5. Factor of safety is resisting shear strength divided by driving shear stress: 36 Γ· 24 = 1.5.
A calculated slope factor of safety below 1 implies:
A Resistance exceeds driving
B Forces are balanced
C Driving exceeds resistance
D Movement is impossible
Answer: C. Driving exceeds resistance. A value below 1 means the modeled driving stress exceeds the modeled shear resistance, so failure is expected under those assumptions.
Effective normal stress equals total normal stress minus:
A Slope angle
B Pore-water pressure
C Rock density
D Surface runoff
Answer: B. Pore-water pressure. In effective-stress analysis, pore-water pressure is subtracted from total normal stress to find the stress carried by the soil skeleton.
A bedding plane dips outward through a slope face. Which movement can it favor?
A Planar sliding
B Rotational slump
C Soil creep
D Debris flow
Answer: A. Planar sliding. A discontinuity that dips out of a slope and daylights at its face can provide a surface for planar sliding.
A cut slope becomes steeper, with material unchanged. Which quantity usually rises?
A Cohesion intercept
B Downslope shear stress
C Root reinforcement
D Pore-water drainage
Answer: B. Downslope shear stress. Steeper slopes generally increase the downslope component of gravitational stress, though full stability also depends on strength, water, and geometry.
At a fixed effective normal stress, a larger friction angle generally:
A Lowers cohesion
B Stops groundwater
C Flattens the slope
D Raises shear strength
Answer: D. Raises shear strength. In the Mohr-Coulomb model, a larger friction angle increases the frictional part of shear strength at the same effective normal stress.
Excavation removes material from a slope toe. What support may be lost?
A Toe buttressing
B Crown loading
C Root suction
D Surface drainage
Answer: A. Toe buttressing. Removing material at the toe can remove resisting support and change the slope stress balance, increasing instability in some settings.
In the Mohr-Coulomb equation, parameter c represents the:
A Friction angle
B Pore pressure
C Cohesion intercept
D Slope gradient
Answer: C. Cohesion intercept. The c parameter is the cohesion intercept in the Mohr-Coulomb shear-strength relation.
A borehole inclinometer is mainly used to detect:
A Rainfall intensity
B Rock mineralogy
C Subsurface lateral movement
D Surface temperature
Answer: C. Subsurface lateral movement. An inclinometer in a borehole measures changes in subsurface inclination, helping locate and monitor movement at depth.
Wetting of an unsaturated slope can remove which strength contribution?
A Rock density
B Matric suction
C Slope length
D Grain color
Answer: B. Matric suction. Unsaturated soils may gain apparent strength from matric suction. Wetting can reduce suction and lower that contribution to shear strength.
An extensometer placed across a ground crack measures:
A Pore-water chemistry
B Slope elevation only
C Sediment grain size
D Crack displacement
Answer: D. Crack displacement. An extensometer records change in distance between fixed points, such as widening or closing across a crack.
Repeated satellite radar interferometry can reveal:
A Surface deformation patterns
B Deep rock chemistry
C Exact failure dates
D Underground pore pressure
Answer: A. Surface deformation patterns. Interferometric radar compares satellite observations to map surface displacement patterns; it does not directly measure deep pore pressure or exact failure timing.
Airborne lidar can help map old landslides beneath forest cover by producing:
A Bare-earth terrain models
B Groundwater chemistry maps
C Subsurface core samples
D Exact movement forecasts
Answer: A. Bare-earth terrain models. Lidar returns through canopy gaps can be processed to model bare-earth topography, revealing scarps and hummocky landslide terrain.
A direct shear test measures soil strength by:
A Heating soil samples
B Measuring river discharge
C Shearing along a set plane
D Counting surface cracks
Answer: C. Shearing along a set plane. A direct shear test applies force to move one soil part along a chosen plane and measures resistance to shearing.
A debris flow grows larger while picking up channel sediment. It is:
A Retrogression
B Entrainment
C Weathering
D Cementation
Answer: B. Entrainment. Entrainment is the incorporation of loose material into a moving flow, which can increase its volume and destructive reach.
After large displacement along a shear surface, its lowest mobilized strength is called:
A Peak strength
B Tensile strength
C Bearing capacity
D Residual strength
Answer: D. Residual strength. Residual shear strength is the lower resistance that may remain after substantial displacement and particle rearrangement along a surface.
Two discontinuity planes intersect and their line daylights on a slope. Which failure is possible?
A Rotational slump
B Soil creep
C Lateral spread
D Wedge failure
Answer: D. Wedge failure. A wedge can slide where two intersecting discontinuities form a block whose line of intersection daylights at the slope face.
Steep joints dipping into a rock slope can favor:
A Toppling failure
B Translational flow
C Soil liquefaction
D Lateral spreading
Answer: A. Toppling failure. Toppling can occur when steep discontinuities dip into the slope, allowing rock columns or blocks to rotate outward.
A localized rupture expands as nearby intact material also begins to fail. This is:
A Rapid drawdown
B Surface creep
C Progressive failure
D Channel incision
Answer: C. Progressive failure. Progressive failure develops as an initial failure redistributes stress and damage into adjacent material, enlarging the rupture zone.
A saturated slope receives a rapid load before water can drain. This is:
A Drained consolidation
B Undrained loading
C Creep equilibrium
D Surface weathering
Answer: B. Undrained loading. When loading occurs faster than drainage, excess pore pressure can develop in saturated soil and alter its effective stress.
The continuity of a rock joint across a slope is its:
A Aperture
B Persistence
C Roughness
D Porosity
Answer: B. Persistence. Persistence describes how far a discontinuity extends through a rock mass. Persistent joints can define larger potential failure blocks.
A landslide susceptibility map differs from a hazard map because hazard adds:
A Only soil color
B Slope aspect alone
C Vegetation height
D Time-based probability
Answer: D. Time-based probability. Susceptibility indicates where conditions favor landslides; hazard also estimates likelihood over a specified time period.
Landslide risk assessment combines hazard with:
A Exposure and vulnerability
B Rock age only
C Slope color only
D Rainfall totals alone
Answer: A. Exposure and vulnerability. Risk depends on the landslide hazard and the people, structures, or systems exposed and vulnerable to its effects.
A slope moves slowly, then its measured velocity increases each survey. The motion is:
A Fully arrested
B Constantly absent
C Accelerating
D Instantaneously reversed
Answer: C. Accelerating. Increasing velocity means movement is accelerating. It can signal changing slope conditions, though it does not establish an exact failure time.
Coarse debris-flow levees commonly accumulate along the:
A Central channel
B Head scarp
C Slope crest
D Flow margins
Answer: D. Flow margins. Coarse clasts can build raised levees along the margins of debris flows, while finer material may continue through the central flow.