Forging shapes metal primarily by what loading?
A Tensile force
B Electrical discharge
C Chemical etching
D Compressive force
Answer: D. Compressive force. Forging plastically deforms metal under compressive forces.
Open-die forging deforms work between what?
A Enclosed cavity dies
B Cutting edges
C Abrasive wheels
D Simple open dies
Answer: D. Simple open dies. Open-die forging uses dies that do not fully enclose the workpiece.
Impression-die forging forms metal in what?
A Shaped die cavity
B Flat rolling gap
C Sand core
D Laser path
Answer: A. Shaped die cavity. Impression dies contain shaped cavities that form the forging.
Hot working is performed above the material’s what temperature?
A Recrystallization temperature
B Melting temperature
C Room temperature always
D Boiling point
Answer: A. Recrystallization temperature. Hot working occurs above the recrystallization temperature but below melting.
Cold working is performed below what temperature?
A Freezing point
B Recrystallization temperature
C Critical pressure
D Melting point only
Answer: B. Recrystallization temperature. Cold working occurs below recrystallization and generally increases strength by strain hardening.
Cold work tends to increase what property?
A Ductility always
B Grain size only
C Material hardness
D Electrical resistance to zero
Answer: C. Material hardness. Plastic deformation at low temperature causes work hardening and raises hardness.
Annealing after cold work can restore what?
A Work hardening
B Ductility
C Residual stress only
D Surface scale
Answer: B. Ductility. Annealing promotes recovery and recrystallization, restoring ductility.
Rolling reduces work thickness between what?
A Rotating rolls
B Punch and die
C Lathe centers
D Welding electrodes
Answer: A. Rotating rolls. Rolling compresses material between rolls to reduce thickness or alter shape.
The neutral point in rolling is where strip and roll have what speed?
A Opposite speed
B Zero pressure
C Equal surface speed
D Equal temperature only
Answer: C. Equal surface speed. At the neutral point, strip velocity equals roll peripheral velocity.
Extrusion forces a billet through what?
A Grinding wheel
B Welding nozzle
C Casting riser
D Die opening
Answer: D. Die opening. Extrusion reduces billet cross-section by forcing it through a die.
In direct extrusion, the ram pushes billet toward what?
A Moving mandrel only
B Stationary die
C Open furnace
D Cutting tool
Answer: B. Stationary die. The billet moves in the same direction as the ram through a fixed die.
Indirect extrusion reduces billet-container friction because what moves?
A Billet through stationary die
B Container with no ram
C Only lubricant
D Die toward billet
Answer: D. Die toward billet. In indirect extrusion, the die moves into the billet and the billet stays largely stationary in the container.
Drawing reduces rod or wire size by pulling through what?
A Die
B Roll gap
C Mold cavity
D Punch
Answer: A. Die. Drawing pulls material through a converging die to reduce cross-section.
Wire drawing applies which dominant load to the workpiece?
A Compression only
B Bending only
C Tension
D Impact only
Answer: C. Tension. The downstream pull draws wire through the die.
Deep drawing converts sheet into what shape?
A Long bar
B Cup-shaped part
C Gear tooth
D Welded pipe
Answer: B. Cup-shaped part. A punch draws a sheet blank into a die cavity to form a cup.
In blanking, the cut-out piece is usually what?
A Scrap slug
B Useful blank
C Punch insert
D Die shoe
Answer: B. Useful blank. Blanking produces a useful cut-out blank from sheet stock.
In punching, the removed slug is usually what?
A Finished blank
B Scrap
C Die block
D Workpiece frame
Answer: B. Scrap. Punching creates a hole; the slug is commonly discarded.
Springback occurs after removing what?
A Bending load
B Cutting fluid
C Rolling pressure
D Welding current
Answer: A. Bending load. Elastic recovery causes a bent sheet to partially return after unloading.
Bend allowance estimates developed length along what?
A Straight flange only
B Neutral axis of shaft
C Bend arc
D Punch travel
Answer: C. Bend arc. Bend allowance accounts for material length through the bend region.
Sheet-metal forming usually starts from what stock form?
A Cast ingot only
B Round shaft
C Powder compact
D Flat sheet
Answer: D. Flat sheet. Sheet-metal processes plastically shape thin flat stock.
Forging can improve strength by aligning what?
A Gas bubbles
B Casting risers
C Grain flow
D Tool wear marks
Answer: C. Grain flow. Forging can orient grain flow along the part contour, improving mechanical properties.
Wavy edges in rolled sheet can result from what?
A Perfectly uniform reduction
B Low cutting speed
C Uneven roll deflection
D Excessive draft angle
Answer: C. Uneven roll deflection. Nonuniform roll bending can cause uneven elongation and wavy edges.
A pipe defect in extrusion may appear as what?
A Surface or center seam
B Casting riser
C Weld undercut
D Grinding burn only
Answer: A. Surface or center seam. Extrusion defects can include surface cracking, pipe defects or internal seams.
Hydroforming uses pressurized what to shape a blank?
A Abrasive powder
B Molten solder
C Laser beam
D Fluid
Answer: D. Fluid. Fluid pressure forces sheet or tube stock against a die.
Superplastic forming requires unusually high what?
A Material ductility
B Tool hardness
C Cutting speed
D Mold permeability
Answer: A. Material ductility. Superplastic alloys undergo large elongation at controlled temperature and strain rate.