Casting forms a part by pouring molten material into what?
A Cutting tool
B Forging die only
C Rolling stand
D Mold cavity
Answer: D. Mold cavity. Casting shapes a part by solidifying molten material in a mold cavity.
A casting pattern is a replica used to form what?
A Final cutting tool
B Weld bead
C Furnace lining
D Mold cavity
Answer: D. Mold cavity. The pattern creates the mold shape that will produce the casting.
Shrinkage allowance on a pattern is generally what?
A Negative enlargement
B Zero in all metals
C Equal to draft
D Positive enlargement
Answer: D. Positive enlargement. A pattern is enlarged to compensate for contraction during cooling.
Draft allowance helps remove pattern from what?
A Mold
B Furnace
C Riser
D Pouring basin
Answer: A. Mold. Draft provides taper so a pattern can be withdrawn without damaging the mold.
A core is used to create what in a casting?
A External draft
B Surface finish
C Internal cavity
D Riser neck
Answer: C. Internal cavity. A core forms internal passages or cavities in a casting.
The sprue is usually which gating passage?
A Vertical down channel
B Horizontal runner
C Riser neck
D Venting groove
Answer: A. Vertical down channel. The sprue carries molten metal downward from the pouring basin.
A runner carries molten metal from sprue toward what?
A Mold gates
B Core prints
C Chills
D Pattern board
Answer: A. Mold gates. The runner distributes metal from the sprue to ingates.
A riser supplies metal to compensate for what?
A Solidification shrinkage
B Tool wear
C Mold erosion only
D Draft removal
Answer: A. Solidification shrinkage. A riser feeds liquid metal as the casting solidifies and contracts.
The gating system controls metal flow into what?
A Mold cavity
B Core box only
C Furnace tuyere
D Pattern rack
Answer: A. Mold cavity. Gates, runners and sprues direct and regulate molten metal flow.
Green-sand molding uses sand with what condition?
A No binder
B Moist binder
C Molten resin only
D Ceramic slurry only
Answer: B. Moist binder. Green sand contains moisture and clay or another binder.
Shell molding binds sand using what?
A Water only
B Thermosetting resin
C Graphite powder only
D Molten metal
Answer: B. Thermosetting resin. Shell molding uses resin-coated sand cured against a heated pattern.
Investment casting commonly uses a disposable what?
A Permanent steel core
B Sand runner
C Wax pattern
D Graphite electrode
Answer: C. Wax pattern. The wax pattern is coated to form a ceramic shell and then removed.
Die casting forces molten metal into a die under what?
A Vacuum only
B Gravity only
C Pressure
D Centrifugal force only
Answer: C. Pressure. Die casting injects molten metal into a reusable die under pressure.
Centrifugal casting uses what to distribute molten metal?
A Electromagnetic field only
B Gravity alone
C Compressed air
D Rotation
Answer: D. Rotation. Rotation drives molten metal against the mold wall.
Hot tearing occurs during casting because of restricted what?
A Pattern draft
B Core removal
C Solidification contraction
D Surface polishing
Answer: C. Solidification contraction. Restricted contraction during solidification can tear a casting while it is weak.
Gas porosity in castings forms from trapped what?
A Sand grains only
B Gas bubbles
C Cold shuts
D Tool marks
Answer: B. Gas bubbles. Gas trapped in the liquid metal creates pores during solidification.
A common advantage of sand casting is what?
A Highest accuracy always
B No finishing needed
C Zero porosity risk
D Low tooling cost
Answer: D. Low tooling cost. Sand molds are inexpensive and can accommodate large, complex parts.
Directional solidification promotes feeding toward what?
A Gate entrance
B Mold wall only
C Riser
D Core surface
Answer: C. Riser. Solidification should progress toward the riser so shrinkage can be fed.
A chill is placed in a mold to do what?
A Increase gas porosity
B Enlarge pattern
C Accelerate local cooling
D Reduce metal fluidity
Answer: C. Accelerate local cooling. Chills extract heat rapidly and control the solidification pattern.
Casting yield is casting mass divided by what?
A Riser mass only
B Total poured metal mass
C Mold mass
D Pattern mass
Answer: B. Total poured metal mass. Yield compares useful casting weight with the total metal poured.
Degassing molten aluminum helps reduce what defect?
A Hot tearing
B Gas porosity
C Draft marks
D Riser shrinkage only
Answer: B. Gas porosity. Dissolved hydrogen can form gas porosity as aluminum solidifies.
Slag inclusion is an unwanted nonmetallic material trapped in what?
A Pattern
B Mold sand only
C Furnace stack
D Casting
Answer: D. Casting. Slag or oxides can become entrained and trapped in the casting.
Permanent-mold casting uses what type of mold?
A Reusable metal mold
B Disposable wax shell
C Green sand mold
D Plaster-only mold
Answer: A. Reusable metal mold. Permanent molds are metallic and can be reused for many castings.
The parting line is where what meet?
A Mold halves
B Riser and gate
C Core and pattern
D Melt and slag
Answer: A. Mold halves. The parting line is the joint between cope and drag mold sections.
A split pattern separates along what feature?
A Riser neck
B Parting plane
C Core print
D Runner channel
Answer: B. Parting plane. A split pattern has two halves meeting at the parting plane.