Difficulty: Easy & Basic
Reliability describes the probability that equipment will do what?
A Change its serial number
B Reduce aircraft mass
C Increase cabin pressure
D Perform required function
Answer: D. Perform required function. Reliability is the probability that an item performs its required function for a stated time and conditions.
A failure mode describes what?
A How a failure occurs
B Who owns a tool
C Where a part ships
D When paint dries
Answer: A. How a failure occurs. A failure mode is the manner in which an item fails to meet its intended function.
Fault isolation aims to identify what?
A Aircraft destination
B Inspection interval
C Failed component or circuit
D Fuel supplier
Answer: C. Failed component or circuit. Fault isolation narrows symptoms to the component or circuit requiring corrective action.
What does a built-in test function help identify?
A Corrosion color
B System faults
C Tool calibration
D Structural weight
Answer: B. System faults. Built-in test equipment checks system status and reports detected faults.
Condition-based maintenance uses what to trigger work?
A Observed equipment condition
B Fixed calendar only
C Paint age
D Passenger demand
Answer: A. Observed equipment condition. Condition-based maintenance schedules work using measured or observed equipment state.
Vibration analysis is useful for monitoring what?
A Composite color
B Cabin lighting
C Fuel grade
D Rotating equipment
Answer: D. Rotating equipment. Vibration trends can reveal imbalance, looseness, bearing wear, or other rotating-equipment problems.
What can oil-debris analysis reveal?
A Runway friction
B Internal wear particles
C Wing incidence
D Cabin pressure
Answer: B. Internal wear particles. Debris in oil can indicate wear in lubricated components before functional failure.
Infrared thermography can reveal what maintenance issue?
A Hidden fastener torque
B Fuel octane
C Abnormal hot spots
D Wing center of gravity
Answer: C. Abnormal hot spots. Thermal imaging identifies temperature patterns that may point to electrical or mechanical faults.
Why compare current sensor values with historical trends?
A Change aircraft configuration
B Remove maintenance records
C Increase part weight
D Spot gradual deterioration
Answer: D. Spot gradual deterioration. Trend monitoring can reveal degrading condition before limits are exceeded.
A hydraulic leak inspection should look for what?
A Fluid traces
B Paint gloss only
C Magnetic north
D Tire tread
Answer: A. Fluid traces. Fresh fluid traces help locate leaks and assess their source and extent.
Galvanic corrosion can occur when dissimilar metals have what?
A Identical coatings only
B Electrical contact and electrolyte
C No moisture
D No potential difference
Answer: B. Electrical contact and electrolyte. Galvanic corrosion requires dissimilar metals electrically connected in an electrolyte.
Moisture trapped beneath insulation increases which risk?
A Improved conductivity
B Lower vibration
C Hidden corrosion
D Reduced fatigue
Answer: C. Hidden corrosion. Moisture retained under insulation can promote corrosion that is difficult to see.
A damaged seal most directly allows what?
A Leakage past a joint
B Higher static margin
C Reduced fatigue cycles
D More accurate torque
Answer: A. Leakage past a joint. Seals prevent fluids or gases from passing through intended interfaces.
A clogged filter may be indicated by what?
A Lower tool count
B Increased wing sweep
C Reduced fastener torque
D Higher pressure drop
Answer: D. Higher pressure drop. Restriction across a filter generally increases pressure differential as it loads with contaminants.
A life-limited part must be replaced by what point?
A First visual scratch
B Approved life limit
C Next paint cycle
D Any mechanic preference
Answer: B. Approved life limit. Life-limited components must be removed by the approved time, cycle, or usage limit.
Why record a component serial number at installation?
A Increase reliability directly
B Set engine timing
C Maintain traceability
D Measure corrosion
Answer: C. Maintain traceability. Serial-number records help track configuration, history, and life status.
Why should maintenance tasks follow a defined sequence?
A Prevent missed steps
B Increase fuel use
C Change component rating
D Reduce inspection access
Answer: A. Prevent missed steps. Following the procedure helps ensure required steps, safety controls, and checks are completed.
What does a signoff on a task record indicate?
A Aircraft ownership
B Work completion status
C Parts price
D Tool storage location
Answer: B. Work completion status. Signoffs identify completion and accountability for assigned maintenance actions.
A maintenance program uses condition monitoring for a bearing. What should be reviewed?
A Paint shade
B Flight destination
C Cabin layout
D Trend and limits
Answer: D. Trend and limits. Condition indicators are compared with approved limits and historical trends.
Work scheduled by flight cycles is most relevant to what?
A Calendar days only
B Aircraft color
C Repeated operating events
D Fuel type
Answer: C. Repeated operating events. Cycle-based tasks track repeated operations such as pressurization or landing events.
MTBF stands for what?
A Mean time between failures
B Maximum torque before failure
C Maintenance task batch frequency
D Measured temperature before flight
Answer: A. Mean time between failures. MTBF is the average operating time between failures for a repairable item.
MTTR measures what?
A Maximum time to run
B Mean time to repair
C Maintenance torque test rate
D Mean temperature to rise
Answer: B. Mean time to repair. MTTR is the average time required to restore an item after a failure.
A recurring fault returns after replacement. What is the next useful step?
A Replace parts repeatedly
B Clear all fault history
C Investigate root cause
D Extend the interval
Answer: C. Investigate root cause. Recurring faults require root-cause investigation rather than repeated part substitution.
Why is accurate defect wording important?
A Increases fuel capacity
B Changes repair limits
C Sets part hardness
D Supports diagnosis
Answer: D. Supports diagnosis. Clear, specific discrepancy descriptions help technicians isolate the actual failure.
A maintenance program revises a task based on reliability data. What is being used?
A In-service performance
B Paint inspection
C Passenger feedback
D Airport elevation
Answer: A. In-service performance. Reliability information from operation can support approved maintenance-program adjustments.