Difficulty: Hard
Hot deposits ignite the charge before the commanded spark. What event is this?
A Normal flame travel
B Diesel injection
C Exhaust blowdown
D Pre-ignition
Answer: D. Pre-ignition. Pre-ignition begins before the scheduled spark, often from an overheated surface.
After the spark begins normal flame travel, what causes SI knock?
A End-gas autoignition
B Valve overlap
C Fuel evaporation
D Oil aeration
Answer: A. End-gas autoignition. Knock occurs when the unburned end gas autoignites after spark-initiated combustion.
Why does higher-octane fuel allow more knock-resistant operation?
A It resists autoignition
B It increases coolant flow
C It lowers compression volume
D It raises cetane quality
Answer: A. It resists autoignition. Octane rating measures resistance to knock in spark-ignition engines.
In a diesel, why can a long ignition delay create harsh combustion?
A Less air enters cylinder
B Exhaust valve stays shut
C More fuel premixes first
D Oil pressure rises quickly
Answer: C. More fuel premixes first. Fuel accumulated during delay can burn rapidly once ignition starts, raising pressure sharply.
How can pilot injection reduce diesel combustion noise?
A It increases exhaust backpressure
B It closes the intake valve
C It softens initial heat release
D It raises fuel viscosity
Answer: C. It softens initial heat release. A small pilot fuel quantity can start combustion more gradually before the main injection.
What does very hot intake air do to SI knock margin?
A Always prevents knock
B Lowers flame temperature
C Stops fuel evaporation
D Usually reduces the margin
Answer: D. Usually reduces the margin. Hotter end gas is more prone to autoignition, reducing knock margin.
Why can excess residual gas destabilize idle combustion?
A It raises fuel octane
B It dilutes the fresh charge
C It increases cylinder bore
D It cools the spark plug only
Answer: B. It dilutes the fresh charge. Residual gas dilutes fresh charge and can slow or destabilize flame development at idle.
Which device limits boost by bypassing exhaust around a turbine?
A Wastegate
B Intercooler
C Throttle body
D Oil separator
Answer: A. Wastegate. A wastegate diverts some exhaust around the turbine to control boost.
What mainly causes turbo lag after a sudden load demand?
A Rotor needs time to spool
B Fuel tank needs refilling
C Crankshaft changes stroke
D Radiator pressure rises
Answer: A. Rotor needs time to spool. The turbo rotor needs exhaust energy to accelerate before boost builds.
Valve overlap occurs when both valves are open near which transition?
A Intake to compression
B Compression to power
C Exhaust to intake
D Power to exhaust
Answer: C. Exhaust to intake. Overlap occurs near gas-exchange TDC between exhaust and intake strokes.
How can moderate valve overlap help at high engine speed?
A It increases oil viscosity
B It prevents all knock
C It improves scavenging
D It reduces piston travel
Answer: C. It improves scavenging. Outgoing exhaust momentum can help draw fresh charge through the cylinder.
At low speed, excessive valve overlap may cause what?
A Higher octane requirement only
B Charge reversion and rough idle
C Lower crankcase pressure
D Faster coolant circulation
Answer: B. Charge reversion and rough idle. Low gas velocity can let exhaust re-enter the intake and destabilize idle.
What does variable valve timing adjust?
A Piston compression height
B Fuel tank pressure
C Valve timing phase
D Crankshaft stroke length
Answer: C. Valve timing phase. Variable valve timing changes when valves open or close relative to crank position.
How do swirl and tumble usually aid combustion?
A Increase bore diameter
B Lower wheel torque
C Store exhaust heat
D Improve charge mixing
Answer: D. Improve charge mixing. Organized in-cylinder motion promotes fuel-air mixing and flame development.
Why can a naturally aspirated engine lose power at altitude?
A Higher fuel density
B Lower air density
C Longer crank stroke
D Higher road resistance
Answer: B. Lower air density. Lower atmospheric density reduces the oxygen mass entering each cylinder.
How is load commonly controlled in a conventional diesel?
A Throttle intake air fully
B Change cylinder count
C Alter crankshaft stroke
D Vary injected fuel quantity
Answer: D. Vary injected fuel quantity. Diesel load is primarily controlled by changing fuel quantity while intake air remains largely unthrottled.
Why can an excessively rich SI mixture raise carbon monoxide?
A Coolant boils earlier
B Compression ratio falls
C Spark voltage becomes zero
D Oxygen is insufficient for complete oxidation
Answer: D. Oxygen is insufficient for complete oxidation. A rich mixture lacks enough oxygen to fully oxidize carbon to carbon dioxide.
Which condition can increase unburned hydrocarbons in exhaust?
A High oil pressure
B Low tire pressure
C Long wheelbase
D Misfire or flame quenching
Answer: D. Misfire or flame quenching. Misfire and flame quenching near walls or crevices can leave unburned fuel.
For efficient SI combustion, peak cylinder pressure is generally targeted when?
A Shortly after TDC
B Far before TDC
C At bottom dead centre
D During exhaust opening
Answer: A. Shortly after TDC. Combustion is phased so useful pressure acts after TDC without excessive early compression work.
How does the Atkinson cycle improve ideal expansion use?
A Expansion exceeds effective compression
B Compression exceeds expansion always
C It removes the exhaust stroke
D It eliminates heat rejection
Answer: A. Expansion exceeds effective compression. Atkinson-cycle valve timing permits a larger expansion ratio than effective compression ratio.
At part load, how can early intake-valve closing reduce pumping loss?
A It increases exhaust backpressure
B It controls trapped charge
C It delays every spark
D It raises brake drag
Answer: B. It controls trapped charge. Valve timing can regulate trapped charge with less throttling, reducing intake pumping work.
What does a cylinder indicator diagram plot?
A Torque against road speed
B Pressure against volume
C Fuel flow against voltage
D Valve lift against time
Answer: B. Pressure against volume. An indicator diagram records cylinder pressure as volume changes through a cycle.
A four-cylinder four-stroke engine runs at 1,500 rpm. Each cylinder gives 600 J per cycle. Indicated power?
A 15 kW
B 45 kW
C 30 kW
D 60 kW
Answer: C. 30 kW. Total cycles per second=4×1,500/(2×60)=50; power=50×600=30,000 W.
Which test helps localize leakage past valves, rings, or gasket?
A Wheel balance test
B Cylinder leak-down test
C Oil viscosity test
D Fuel octane test
Answer: B. Cylinder leak-down test. A leak-down test pressurizes a cylinder and listens for air escaping through likely leak paths.
Two adjacent cylinders show similarly low compression. What fault is suggested?
A Blocked fuel filter
B Worn alternator belt
C Stuck thermostat
D Gasket leak between cylinders
Answer: D. Gasket leak between cylinders. A leak between adjacent cylinders can lower both readings; confirm with further diagnosis.