Direct-on-line starting applies what voltage to the stator?
A Half frequency only
B Full line voltage
C Zero voltage
D Rotor DC voltage
Answer: B. Full line voltage. A DOL starter connects the motor directly to its rated supply.
For a motor designed to run in delta, starting in star reduces each phase voltage to what fraction of delta phase voltage?
A 1/√3
B √3
C 1/3
D Equal
Answer: A. 1/√3. At the same line voltage, star phase voltage is VL/√3 while delta phase voltage is VL.
Compared with DOL delta starting, ideal star-delta starting torque is about what fraction?
A Three times
B Equal
C Two thirds
D One third
Answer: D. One third. Starting torque scales with phase voltage squared, giving roughly 1/3.
Compared with DOL delta starting, ideal star-delta line starting current is about what fraction?
A One third
B Three times
C Equal
D One half
Answer: A. One third. Star phase voltage and line-current relationships yield about one third the delta DOL line current.
An autotransformer starter applies what to the motor during starting?
A Pure DC current
B Higher frequency only
C Reduced AC voltage
D Direct mechanical torque
Answer: C. Reduced AC voltage. A tapped autotransformer lowers motor terminal voltage and starting current.
If an autotransformer applies 80% rated motor voltage, starting torque is about what fraction of DOL torque?
A 80%
B 40%
C 125%
D 64%
Answer: D. 64%. At the same slip, torque is approximately proportional to voltage squared: 0.8²=0.64.
A soft starter usually limits starting current by controlling what?
A Rotor pole count
B Applied stator voltage
C Mechanical gear ratio
D Core lamination
Answer: B. Applied stator voltage. Thyristor phase control ramps the effective stator voltage.
A variable-frequency drive primarily controls motor speed by changing what?
A Supply frequency
B Rotor bar length
C Bearing friction
D Earth resistance
Answer: A. Supply frequency. Synchronous speed varies directly with electrical frequency.
Why is voltage often reduced in proportion to frequency below base speed?
A Increase core saturation
B Remove slip
C Reverse phase sequence
D Maintain approximate flux
Answer: D. Maintain approximate flux. A roughly constant V/f ratio helps keep air-gap flux near rated value.
For unchanged poles, reducing supply frequency from 50 Hz to 25 Hz does what to synchronous speed?
A Doubles it
B Halves it
C Leaves it unchanged
D Makes it zero
Answer: B. Halves it. Ns=120f/P, so halving f halves Ns.
Above base frequency with a limited maximum voltage, what happens to available air-gap flux?
A It doubles
B It stays exactly fixed
C It weakens
D It reverses
Answer: C. It weakens. When voltage cannot rise with frequency, V/f declines and flux weakens.
Pole-changing control typically produces what kind of speed adjustment?
A Discrete speeds
B Continuous infinite speeds
C Only zero speed
D Constant speed at all poles
Answer: A. Discrete speeds. Switching effective pole number changes synchronous speed in steps.
External rotor resistors can improve starting torque of which induction motor?
A Standard cage motor
B Wound-rotor motor
C Permanent-magnet motor
D Synchronous condenser
Answer: B. Wound-rotor motor. Slip rings allow added rotor resistance during starting.
Why can a deep-bar rotor have higher effective resistance at starting?
A DC field excitation
B Zero rotor frequency
C Reduced pole count
D Rotor skin effect
Answer: D. Rotor skin effect. High rotor frequency at standstill crowds current toward the bar surface.
In a double-cage rotor, which cage helps starting torque through higher resistance?
A Outer cage
B Inner low-resistance cage
C Stator winding
D Shaft
Answer: A. Outer cage. The outer cage has higher effective resistance at high starting rotor frequency.
How is direction reversed for a three-phase induction motor?
A Increase all three voltages
B Short one phase
C Exchange two phases
D Change rotor resistance only
Answer: C. Exchange two phases. Swapping two stator leads reverses phase sequence and rotating field.
Plugging a running three-phase induction motor can be initiated by what?
A Open both bearings
B Reverse stator phase sequence
C Reduce voltage to zero
D Increase pole count only
Answer: B. Reverse stator phase sequence. Reversing the rotating field creates a torque opposing rotor rotation.
DC-injection braking produces what kind of stator field?
A Faster rotating field
B Zero magnetic field
C High-frequency field
D Stationary field
Answer: D. Stationary field. Applied DC establishes a stationary magnetic field that induces braking currents in a moving rotor.
When an induction machine rotor is driven above synchronous speed, what is slip?
A Exactly 1
B Between 0 and 1
C Negative
D Infinite
Answer: C. Negative. Nr>Ns makes (Ns−Nr)/Ns negative, corresponding to generating operation.
What operating mode occurs when a grid-connected induction machine is driven above synchronous speed?
A Generation
B Locked-rotor starting
C No-load motoring
D DC braking
Answer: A. Generation. Mechanical input can be converted to electrical power while the grid supplies magnetizing reactive power.
Why are capacitors sometimes installed near induction motors?
A Increase mechanical friction
B Change rotor poles
C Supply reactive power
D Create commutator
Answer: C. Supply reactive power. Capacitors can offset some lagging magnetizing VAR demand.
At very light load, induction motor power factor is usually what?
A Exactly unity
B Always leading
C Exactly zero current
D Low and lagging
Answer: D. Low and lagging. Magnetizing current remains significant while real load current is small.
A large direct-on-line starting current can cause which supply effect?
A Voltage dip
B Frequency doubling
C DC output
D Perfect power factor
Answer: A. Voltage dip. High inrush through supply impedance temporarily depresses terminal voltage.
A thermal overload relay protects chiefly against what?
A Every lightning surge
B Oil leakage
C Prolonged overcurrent heating
D Phase sequence only
Answer: C. Prolonged overcurrent heating. Its delayed trip responds to sustained heating from excessive current.
A VFD slip-compensation function tends to raise commanded frequency when load rises to maintain what?
A Core loss
B Rotor speed
C Rotor resistance
D Pole count
Answer: B. Rotor speed. It offsets the increased slip and associated speed droop under load.