In the per-phase induction-motor equivalent circuit, which rotor term models slip-dependent power transfer?
A R2′×s
B Xm/s
C X1×s
D R2′/s
Answer: D. R2′/s. The referred rotor resistance divided by slip represents rotor copper loss and converted power.
If referred rotor current is I2′, which expression gives three-phase air-gap power?
A 3I2′²R2′s
B I2′/R2′
C 3V1²Xm
D 3I2′²R2′/s
Answer: D. 3I2′²R2′/s. Air-gap power enters the rotor branch R2′/s in the equivalent circuit.
Rotor copper loss is what fraction of air-gap power in an induction motor?
A Slip s
B 1−s
C 1/s
D s²
Answer: A. Slip s. Pcu,rotor=sPag.
Developed mechanical power before friction and windage equals which fraction of air-gap power?
A s
B 1+s
C 1−s
D 1/s
Answer: C. 1−s. The remainder after rotor copper loss is (1−s)Pag.
At 5% slip and 10 kW air-gap power, what is rotor copper loss?
A 0.5 kW
B 0.05 kW
C 5 kW
D 9.5 kW
Answer: A. 0.5 kW. sPag=0.05×10 kW=0.5 kW.
At 5% slip and 10 kW air-gap power, what is developed mechanical power?
A 9.5 kW
B 0.5 kW
C 10.5 kW
D 5 kW
Answer: A. 9.5 kW. (1−s)Pag=0.95×10=9.5 kW.
Electromagnetic torque equals air-gap power divided by which angular speed?
A Synchronous angular speed
B Rotor slip frequency
C Supply voltage
D Mechanical loss
Answer: A. Synchronous angular speed. Torque is Pag/ωs, equivalently developed power divided by rotor angular speed.
Stator copper loss for a three-phase motor is approximately what?
A I1/R1
B 3I1²R1
C 3I1R1²
D R1/3I1
Answer: B. 3I1²R1. Each of three stator phases dissipates I1²R1.
Which pair makes up the main core losses?
A Hysteresis and eddy currents
B Brush and bearing loss
C Slip and torque
D Copper and windage
Answer: A. Hysteresis and eddy currents. Alternating magnetic flux produces hysteresis and eddy-current heating.
Which losses reduce developed mechanical power to shaft output?
A Only rotor copper loss
B Only stator copper loss
C Only core loss
D Friction and windage
Answer: D. Friction and windage. Rotational mechanical losses consume part of developed power.
At locked rotor, what is slip?
A 0
B −1
C Infinity
D 1
Answer: D. 1. Rotor speed is zero, giving unit slip.
Why is a blocked-rotor test normally run at reduced voltage?
A To stop core flux entirely
B To limit current
C To increase frequency
D To produce rated speed
Answer: B. To limit current. At standstill, the motor has low impedance and draws high current.
Rotor leakage reactance at actual rotor frequency is approximately proportional to what?
A 1/slip
B Slip
C Voltage squared
D Mechanical torque only
Answer: B. Slip. Rotor frequency is sf, so its leakage reactance scales with s.
Rotor induced EMF at nonzero slip is approximately what fraction of standstill value?
A 1−s
B 1/s
C s
D s²
Answer: C. s. Relative speed and induced rotor EMF are proportional to slip.
Why can direct-on-line starting cause high current?
A Low standstill impedance
B High rotor speed
C Zero supply voltage
D Open rotor circuit
Answer: A. Low standstill impedance. At s=1, the motor draws a large current through its low equivalent impedance.
At fixed slip, electromagnetic torque is approximately proportional to what supply quantity?
A Voltage inverse
B Voltage squared
C Frequency squared only
D Current inverse
Answer: B. Voltage squared. With approximately constant impedances, rotor current and torque yield a V² dependence.
If voltage falls to 80% at fixed slip, torque is approximately what fraction of former value?
A 80%
B 40%
C 64%
D 125%
Answer: C. 64%. 0.8²=0.64, subject to the approximate fixed-slip model.
The highest point on a motoring torque-slip curve is called what?
A No-load torque
B Friction torque
C Breakdown torque
D Synchronous torque
Answer: C. Breakdown torque. Breakdown or pull-out torque is the maximum electromagnetic torque.
Adding rotor resistance to a wound-rotor motor shifts maximum torque toward what slip?
A Higher slip
B Lower slip
C Exactly zero slip
D Negative slip
Answer: A. Higher slip. The slip at maximum torque increases with effective rotor resistance.
Ideally, increasing rotor resistance while keeping voltage fixed has what effect on maximum torque magnitude?
A Always doubled
B Approximately unchanged
C Always zero
D Inversely squared
Answer: B. Approximately unchanged. In the simplified model, it changes the slip of the peak more than its height.
Near synchronous speed, motor torque is approximately proportional to what?
A 1/slip
B Slip squared only
C Slip
D Zero voltage
Answer: C. Slip. At small s, rotor resistance dominates and T grows nearly linearly with slip.
When shaft load rises within the stable region, what happens to slip?
A It becomes zero
B It turns negative
C It increases
D It is always fixed
Answer: C. It increases. The rotor slows slightly to induce more rotor current and torque.
A blocked-rotor test chiefly helps determine which equivalent-circuit terms?
A Only core-loss resistance
B Only rated speed
C Only shaft friction
D Series impedance
Answer: D. Series impedance. Reduced-voltage locked-rotor measurements reveal combined leakage impedance and resistance.
A no-load test helps estimate which combination?
A Only rated rotor copper loss
B Only short-circuit current
C Only pole count
D Core and rotational losses
Answer: D. Core and rotational losses. At light load, input power mainly covers core and friction/windage losses.
Ignoring mechanical losses, rotor efficiency of power conversion is approximately what?
A s
B 1−s
C 1/s
D s²
Answer: B. 1−s. The fraction of air-gap power converted to mechanical form is 1−s.