A heat exchanger transfers energy between what?
A Two solid gears
B Two fluid streams
C A shaft and bearing
D A fluid and vacuum only
Answer: B. Two fluid streams. Heat exchangers transfer heat between fluids, usually without mixing them.
In parallel-flow exchangers, fluids move in what directions?
A Opposite directions
B At right angles only
C Same direction
D No defined direction
Answer: C. Same direction. Both streams enter at the same end and flow in the same direction.
In counterflow exchangers, fluids move in what directions?
A Same direction
B Both rotate
C Only vertically
D Opposite directions
Answer: D. Opposite directions. The two fluids travel in opposite directions through a counterflow exchanger.
LMTD is the logarithmic mean of which quantities?
A Fluid densities
B Pressure drops
C Heat capacities
D End temperature differences
Answer: D. End temperature differences. The log-mean temperature difference combines the two terminal temperature differences.
Counterflow often gives higher LMTD than parallel flow for what?
A Zero heat duty
B Different fluids only
C Same terminal temperatures
D No temperature change
Answer: C. Same terminal temperatures. Counterflow generally provides a larger mean temperature difference for comparable terminal states.
A correction factor adjusts LMTD for what exchanger?
A Single plane wall
B Blackbody enclosure
C Simple pipe bend
D Multipass exchanger
Answer: D. Multipass exchanger. Multipass and crossflow arrangements use an LMTD correction factor.
Heat-exchanger effectiveness is actual heat transfer divided by what?
A Inlet pressure
B Surface area
C Thermal conductivity
D Maximum possible heat transfer
Answer: D. Maximum possible heat transfer. Effectiveness ε = q_actual/q_max.
Number of transfer units equals UA divided by what?
A Minimum heat-capacity rate
B Maximum temperature
C Fluid density
D Mass of wall
Answer: A. Minimum heat-capacity rate. NTU = UA/C_min.
Fouling resistance represents what buildup effect?
A Higher fluid velocity
B Lower wall thickness
C Deposited surface layer
D Radiation shield
Answer: C. Deposited surface layer. Deposits add thermal resistance and reduce heat-exchanger performance.
Overall heat-transfer coefficient combines which resistances?
A Conduction and convection
B Mass and momentum
C Only radiation
D Only fluid inertia
Answer: A. Conduction and convection. Overall U accounts for convection films, wall conduction and fouling resistances.
A shell-and-tube exchanger contains tubes inside what?
A Outer shell
B Open channel
C Rotating drum
D Vacuum tank only
Answer: A. Outer shell. Tube-side and shell-side fluids exchange heat across tube walls.
A crossflow exchanger has fluid streams moving how?
A Perpendicular to each other
B In same direction
C In opposite axial direction
D Along one pipe only
Answer: A. Perpendicular to each other. In crossflow, one stream moves transverse to the other.
A condenser changes vapor mainly into what?
A Superheated vapor
B Liquid
C Solid
D Noncondensable gas
Answer: B. Liquid. Condensation rejects latent heat as vapor becomes liquid.
Boiling heat transfer involves what phase change?
A Vapor to liquid
B Liquid to vapor
C Solid to liquid
D Gas to plasma
Answer: B. Liquid to vapor. Boiling occurs when liquid changes to vapor at a heated surface.
Fin efficiency compares actual transfer with what ideal condition?
A Fin at ambient temperature
B Zero conductivity
C Entire fin at base temperature
D No convection
Answer: C. Entire fin at base temperature. Ideal fin transfer assumes the whole fin stays at base temperature.
The fin parameter m contains h, perimeter and what area property?
A Surface roughness
B Cross-sectional area
C Base temperature
D Fluid density only
Answer: B. Cross-sectional area. For a straight fin, m = sqrt(hP/(kA_c)).
The Biot number compares convection resistance with what?
A Radiation resistance only
B Internal conduction resistance
C Fluid inertia
D Mass transfer resistance
Answer: B. Internal conduction resistance. Bi = hL_c/k_s compares surface convection to internal conduction.
Lumped-capacitance analysis is often valid when Bi is below what?
A About 1
B About 10
C About 0.1
D About 100
Answer: C. About 0.1. Bi < 0.1 indicates small internal temperature gradients for lumped analysis.
The Fourier number equals diffusivity times time divided by what?
A Length squared
B Area
C Temperature
D Conductivity
Answer: A. Length squared. Fo = αt/L_c² measures transient conduction time relative to diffusion time.
A lumped thermal body is assumed to have what internal temperature?
A Linear temperature profile
B Parabolic temperature profile
C Infinite gradient
D Spatially uniform temperature
Answer: D. Spatially uniform temperature. Lumped-capacitance analysis treats the solid as internally isothermal at each instant.
Nucleate boiling is characterized by what at the surface?
A Vapor bubble formation
B A stable thick vapor blanket
C No phase change
D Only natural convection
Answer: A. Vapor bubble formation. Nucleate boiling forms bubbles at active surface sites and often has high heat-transfer rates.
Film boiling has what layer adjacent to hot surface?
A Liquid-only layer
B Solid deposit only
C Continuous vapor film
D Air gap always
Answer: C. Continuous vapor film. In film boiling, a vapor blanket separates liquid from the hot surface.
Dropwise condensation often has what relative coefficient?
A Lower than filmwise always
B Exactly zero
C Same as conduction
D Higher than filmwise
Answer: D. Higher than filmwise. Dropwise condensation leaves more surface exposed and commonly transfers heat more effectively.
Critical insulation radius for a cylinder equals conductivity divided by what?
A Wall thickness
B External coefficient h
C Specific heat
D Fluid density
Answer: B. External coefficient h. For cylindrical insulation, the critical radius is r_c = k_ins/h.
A heat exchanger’s energy balance relates heat lost by hot fluid to what?
A Heat gained by cold fluid
B Wall mass only
C Fouling factor
D Ambient pressure
Answer: A. Heat gained by cold fluid. Neglecting losses, heat rejected by the hot stream equals heat absorbed by the cold stream.