Convection transfers heat between a surface and what?
A Vacuum only
B Moving fluid
C Solid lattice only
D Radiation shield only
Answer: B. Moving fluid. Convection combines conduction near a surface with bulk fluid motion.
Newton’s cooling law is what relation?
A q = hAΔT
B q = kA/L
C q = mcpΔT
D q = σAT⁴
Answer: A. q = hAΔT. Convective heat transfer rate is hA times the surface-to-fluid temperature difference.
The convection coefficient h depends strongly on what?
A Solid color only
B Mass of wall
C Pipe length only
D Flow and geometry
Answer: D. Flow and geometry. The coefficient depends on fluid properties, flow regime, geometry and boundary conditions.
Nusselt number equals hL divided by what?
A Density
B Fluid conductivity
C Specific heat
D Dynamic pressure
Answer: B. Fluid conductivity. Nu = hL/k_f is dimensionless convection heat transfer.
Prandtl number compares momentum diffusivity with what?
A Thermal diffusivity
B Surface tension
C Density ratio
D Pressure head
Answer: A. Thermal diffusivity. Pr = ν/α compares momentum and thermal diffusion rates.
Forced convection is driven mainly by what?
A External flow motion
B Buoyancy only
C Radiation only
D Surface tension
Answer: A. External flow motion. Forced convection uses a fan, pump or other imposed flow.
Natural convection is driven mainly by what?
A Mechanical stirring
B Buoyancy forces
C Radiation pressure
D Surface roughness
Answer: B. Buoyancy forces. Density differences caused by temperature variations drive natural convection.
A hydrodynamic boundary layer describes variation in what?
A Pressure in vacuum
B Solid temperature only
C Fluid composition
D Velocity near surface
Answer: D. Velocity near surface. Viscous effects create a near-wall velocity boundary layer.
A thermal boundary layer describes variation in what?
A Velocity only
B Pressure only
C Density alone
D Temperature near surface
Answer: D. Temperature near surface. The thermal boundary layer is the region where fluid temperature changes from wall to free stream.
Turbulence often increases convection by increasing what?
A Fluid mixing
B Thermal resistance
C Boundary thickness always
D Surface roughness only
Answer: A. Fluid mixing. Turbulent mixing transports heat more effectively across the flow.
A characteristic length is used in which calculation?
A Mass conservation only
B Energy storage only
C Material selection
D Dimensionless correlations
Answer: D. Dimensionless correlations. Convection correlations use a representative geometry length to form dimensionless groups.
For flow over a flat plate, local Reynolds number uses distance from what?
A Trailing edge only
B Plate center
C Fluid outlet
D Leading edge
Answer: D. Leading edge. The local flat-plate Reynolds number is based on distance x from the leading edge.
Fully developed internal flow has what axial profile shape?
A Zero velocity
B Constant pressure always
C Uniform temperature always
D Unchanging profile
Answer: D. Unchanging profile. The velocity profile no longer changes with downstream position after hydrodynamic development.
Hydrodynamic entrance length ends when what is established?
A Thermal equilibrium
B Velocity profile
C Zero pressure drop
D Critical flow only
Answer: B. Velocity profile. The hydrodynamic entrance region ends when the velocity profile becomes fully developed.
Thermal entrance length ends when what is established?
A Velocity becomes zero
B Surface becomes insulated
C Temperature profile shape
D Density becomes constant
Answer: C. Temperature profile shape. The thermal profile shape becomes fully developed after the thermal entrance region.
Bulk mean temperature represents what in internal flow?
A Wall temperature only
B Mixed-mean fluid temperature
C Inlet temperature always
D Maximum local temperature
Answer: B. Mixed-mean fluid temperature. Bulk mean temperature is the energy-averaged fluid temperature across a section.
Increasing forced-flow velocity usually does what to h?
A Decreases h always
B Makes h zero
C Increases h
D Leaves h fixed always
Answer: C. Increases h. Higher velocity generally strengthens convection and raises the heat-transfer coefficient.
Grashof number compares buoyancy with what?
A Inertial forces only
B Radiation exchange
C Viscous forces
D Thermal storage
Answer: C. Viscous forces. Gr measures buoyancy relative to viscous effects in natural convection.
Rayleigh number equals Grashof times what?
A Nusselt number
B Reynolds number
C Prandtl number
D Biot number
Answer: C. Prandtl number. Ra = Gr Pr.
Mixed convection includes forced flow and what contribution?
A Buoyancy effects
B Only radiation
C Only conduction
D Surface tension only
Answer: A. Buoyancy effects. Mixed convection occurs when imposed flow and buoyancy both matter.
Convection heat rate rises with larger surface what?
A Area
B Thermal resistance
C Fluid viscosity always
D Wall thickness
Answer: A. Area. Newton’s law shows heat transfer is proportional to surface area for fixed h and ΔT.
A hydrodynamic entry region begins at what location?
A Pipe outlet
B Flow inlet
C Pipe midpoint always
D Wall center
Answer: B. Flow inlet. The developing velocity boundary layer starts at the inlet.
The hydraulic diameter for a duct is four area divided by what?
A Wetted perimeter
B Duct length
C Flow velocity
D Wall thickness
Answer: A. Wetted perimeter. Hydraulic diameter is 4A/P_w for noncircular ducts.
A larger heat-transfer coefficient indicates what?
A Lower conductivity always
B Lower fluid speed
C Greater heat transfer per area
D Higher wall resistance
Answer: C. Greater heat transfer per area. For a given area and temperature difference, larger h means greater convective heat transfer.
The convection film temperature is often approximated by what?
A Wall temperature only
B Inlet pressure
C Average wall and fluid temperatures
D Outlet density
Answer: C. Average wall and fluid temperatures. For property evaluation, a film temperature is often the mean of surface and bulk-fluid temperatures.