Difficulty: Hard
A section oblique to fault strike shows an apparent dip that is usually:
A Less than true dip
B Greater than true dip
C Exactly vertical
D Always zero
Answer: A. Less than true dip. Apparent dip is measured in a section not perpendicular to strike and is less than or equal to true dip.
Net slip on a fault is displacement measured:
A Only vertically
B Only horizontally
C Along the fault plane
D Across a fold axis
Answer: C. Along the fault plane. Net slip is the total movement along the fault surface.
A reverse fault dipping 35 degrees is generally classified as a:
A Normal fault
B Thrust fault
C Joint set
D Strike-slip fault
Answer: B. Thrust fault. USGS defines thrust faults as reverse faults dipping 45 degrees or less.
A normal fault that curves and flattens with depth is:
A Vertical
B Antithetic fold
C Blind thrust
D Listric
Answer: D. Listric. Listric faults have curved surfaces that commonly flatten at depth.
Beds bending in the hanging wall above a curved normal fault may form a:
A Klippe
B Fault window
C Rollover anticline
D Synclinorium
Answer: C. Rollover anticline. Hanging-wall beds may bend into rollover folds above listric normal faults.
A low-angle extensional fault separating brittle upper rocks from deeper ductile rocks is a:
A Detachment fault
B Thrust window
C Transform fault
D Joint plane
Answer: A. Detachment fault. Detachment faults can accommodate extension in brittle upper crust above warmer, more ductile rocks.
Thrusting above a décollement with little basement involvement is:
A Thick-skinned tectonics
B Thin-skinned tectonics
C Strike-slip tectonics
D Thermal subsidence
Answer: B. Thin-skinned tectonics. Thin-skinned deformation mainly affects cover rocks detached from basement along a weak horizon.
Deformation that significantly involves crystalline basement is:
A Thin-skinned tectonics
B Surface creep
C Flexural slip
D Thick-skinned tectonics
Answer: D. Thick-skinned tectonics. Thick-skinned deformation includes structures that involve basement rocks.
A single thrust-bounded slice inside a duplex is a:
A Klippe
B Horse
C Window
D Ramp
Answer: B. Horse. Individual thrust slices in a duplex are commonly called horses.
An isolated erosional remnant of a thrust sheet is a:
A Duplex
B Half-graben
C Klippe
D Hogback
Answer: C. Klippe. A klippe is an erosional remnant separated from the main thrust sheet.
An erosional opening through a thrust sheet exposing underlying rocks is a:
A Klippe
B Rollover fold
C Fault scarp
D Tectonic window
Answer: D. Tectonic window. A tectonic window exposes underlying rocks through an erosional opening in an overlying thrust sheet.
Movement that reuses an older fault surface is:
A Fault reactivation
B Fold propagation
C Joint opening
D Surface creep
Answer: A. Fault reactivation. Fault reactivation occurs when an existing fault slips again.
Crustal shortening combined with strike-slip shear is:
A Transtension
B Subsidence
C Isostasy
D Transpression
Answer: D. Transpression. Transpression combines shortening with strike-slip deformation.
Crustal extension combined with strike-slip shear is:
A Transpression
B Transtension
C Compression
D Pure folding
Answer: B. Transtension. Transtension combines extension with strike-slip deformation.
A fold and fault system with a major décollement level change along strike has a:
A Lateral ramp
B Frontal ramp
C Normal scarp
D Fold hinge
Answer: A. Lateral ramp. A lateral ramp changes décollement level parallel to structural strike.
A thrust ramp changing décollement level across strike is a:
A Lateral ramp
B Half-graben
C Frontal ramp
D Axial plane
Answer: C. Frontal ramp. A frontal ramp changes décollement level perpendicular to structural strike.
An abrupt fold termination along strike may signal a:
A Basin center
B Normal joint
C River terrace
D Lateral ramp
Answer: D. Lateral ramp. Lateral ramps can be associated with abrupt changes or terminations in folds along strike.
A steeply dipping resistant bed eroded into a narrow ridge may form a:
A Hogback
B Klippe
C Tectonic window
D Half-graben
Answer: A. Hogback. USGS examples describe hogback ridges along resistant steeply dipping strata.
Tilted resistant rock slabs exposed by erosion can create:
A Fault gouge
B Flatirons
C Growth strata
D Axial traces
Answer: B. Flatirons. USGS describes Colorado’s Flatirons as tilted rocks exposed by erosion.
In the Basin and Range, many high blocks and valleys reflect:
A Oceanic subduction
B Continent collision
C Extension and faulting
D River deposition
Answer: C. Extension and faulting. USGS relates Basin and Range horsts and grabens to regional extension.
A very fresh fault scarp can become subdued over time through:
A Magnetic reversal
B Continental drift
C Crustal melting
D Erosion and deposition
Answer: D. Erosion and deposition. Weathering, erosion, and sediment deposition can soften a fault scarp’s relief.
Matching stream channels offset horizontally across a fault indicate:
A Lateral displacement
B Vertical folding
C No fault movement
D Magma intrusion
Answer: A. Lateral displacement. Correlated stream segments can record horizontal movement across a strike-slip fault.
A broad regional upfold containing smaller folds is an:
A Synclinorium
B Half-graben
C Anticlinorium
D Lateral ramp
Answer: C. Anticlinorium. An anticlinorium is a large anticlinal structure with subsidiary folds.
A broad regional downfold containing smaller folds is a:
A Anticlinorium
B Synclinorium
C Horst
D Detachment
Answer: B. Synclinorium. A synclinorium is a large synclinal structure containing smaller folds.
Uplift above a buried thrust rupture during an earthquake may reflect:
A River capture
B Glacial rebound
C Thermal subsidence
D Co-seismic folding
Answer: D. Co-seismic folding. Blind-thrust earthquakes can produce folding and uplift above the buried rupture.