Difficulty: Easy & Basic
What makes a fracture a fault?
A Only surface weathering
B No displacement occurred
C Rock blocks moved
D Magma filled a crack
Answer: C. Rock blocks moved. A fault is a fracture along which rock blocks have moved relative to one another.
In an anticline, the oldest beds are usually:
A At the core
B At the limbs
C Only above ground
D Along a fault
Answer: A. At the core. An anticline is a fold with older strata in its core.
Which fold usually has youngest beds at its core?
A Anticline
B Monocline
C Horst
D Syncline
Answer: D. Syncline. Synclines commonly preserve younger strata in their center.
The block above an inclined fault is the:
A Footwall
B Hanging wall
C Fold limb
D Fault scarp
Answer: B. Hanging wall. The hanging wall lies above an inclined fault plane.
The block below an inclined fault is the:
A Footwall
B Hanging wall
C Fold hinge
D Axial trace
Answer: A. Footwall. The footwall is the rock mass beneath the fault plane.
In a normal fault, the hanging wall moves:
A Upward
B Sideways only
C Downward
D Not at all
Answer: C. Downward. A normal fault has downward motion of the hanging wall relative to the footwall.
Normal faulting commonly reflects:
A Crustal shortening
B Pure rotation
C Chemical weathering
D Crustal extension
Answer: D. Crustal extension. Normal faults commonly form as the crust is pulled apart.
Reverse faulting commonly reflects:
A Extension
B Compression
C Evaporation
D Deposition
Answer: B. Compression. Compression tends to move the hanging wall up on a reverse fault.
A thrust fault is a low-angle:
A Normal fault
B Strike-slip fault
C Joint
D Reverse fault
Answer: D. Reverse fault. A thrust fault is a reverse fault with a relatively low dip angle.
In strike-slip motion, blocks move mainly:
A Vertically
B Downward only
C Horizontally
D By folding
Answer: C. Horizontally. Strike-slip faults accommodate predominantly horizontal movement.
A fracture without significant displacement is a:
A Fault
B Joint
C Thrust
D Graben
Answer: B. Joint. A joint is a fracture with little or no measurable displacement.
The surface carrying fault slip is the:
A Fault plane
B Fold axis
C Bedding top
D Hinge zone
Answer: A. Fault plane. The fault plane is the surface along which the blocks move.
A step-like bend in rock layers is a:
A Anticline
B Syncline
C Monocline
D Graben
Answer: C. Monocline. A monocline is a step-shaped fold in otherwise gently dipping or horizontal strata.
The side of a fold is called a:
A Hinge
B Throw
C Scarp
D Limb
Answer: D. Limb. Fold limbs extend away from the hinge region.
The most curved part of a fold is its:
A Hinge
B Limb
C Fault plane
D Footwall
Answer: A. Hinge. The hinge is the zone of greatest curvature in a fold.
A line following a fold’s hinge is its:
A Fault trace
B Fold axis
C Strike line
D Dip direction
Answer: B. Fold axis. The fold axis follows the hinge line of a fold.
A fold axis tilted from horizontal defines a:
A Flat fold
B Vertical fault
C Plunging fold
D Structural joint
Answer: C. Plunging fold. A plunging fold has an axis inclined to the horizontal.
A structural dome generally exposes oldest rocks:
A Near its center
B At its outer rim
C Only on one limb
D Below a fault
Answer: A. Near its center. In a dome, strata generally dip outward and older rocks occur toward the center.
A structural basin generally has youngest rocks:
A At its outer rim
B Only on one limb
C Above a thrust
D Near its center
Answer: D. Near its center. Basin strata dip inward, commonly placing younger rocks near the center.
A down-dropped block between normal faults is a:
A Horst
B Graben
C Dome
D Anticline
Answer: B. Graben. A graben is a block that has subsided between bounding faults, commonly normal faults.
An uplifted block between normal faults is a:
A Horst
B Graben
C Syncline
D Monocline
Answer: A. Horst. A horst is an uplifted or relatively high block between faults.
What chiefly distinguishes folding from faulting?
A Heating versus cooling
B Uplift versus erosion
C Magma versus lava
D Bending versus breakage
Answer: D. Bending versus breakage. Folding bends rock layers, while faulting fractures and displaces them.
A step in terrain created by fault displacement is a:
A Fold limb
B Bedding plane
C Fault scarp
D Hinge line
Answer: C. Fault scarp. A fault scarp is a slope or step produced by displacement at a fault.
Motion parallel to a fault’s dip direction is:
A Strike-slip
B Dip-slip
C No-slip
D Fold-slip
Answer: B. Dip-slip. Dip-slip motion is parallel to the dip direction of the fault plane.
Fault movement with vertical and horizontal components is:
A Pure dip-slip
B Pure strike-slip
C Oblique-slip
D No displacement
Answer: C. Oblique-slip. Oblique-slip combines dip-slip and strike-slip components.