Difficulty: Medium
Layer-parallel shortening of rock beds commonly produces:
A Normal faults
B Buckle folds
C Joint sets
D Dome collapse
Answer: B. Buckle folds. Layer-parallel compression can cause competent layers to buckle into folds.
During flexural-slip folding, adjacent beds accommodate bending through:
A Magma injection
B Surface weathering
C Vertical settling
D Sliding along bedding
Answer: D. Sliding along bedding. Flexural-slip folding allows adjacent beds to slip along bedding surfaces as they bend.
Small folds superimposed on a large fold are called:
A Growth faults
B Joint swarms
C Parasitic folds
D Fault scarps
Answer: C. Parasitic folds. Parasitic folds are smaller structures associated with a larger fold.
Bending of strata next to a moving fault is termed:
A Drag folding
B Rift spreading
C Joint opening
D Soil creep
Answer: A. Drag folding. Drag folds develop as nearby strata are bent by fault displacement.
Different fold shapes in adjacent layers indicate:
A Uniform tilting
B Pure translation
C Surface erosion
D Disharmonic folding
Answer: D. Disharmonic folding. Mechanical contrasts between layers can produce disharmonic folds.
The horizontal distance between equivalent fold hinges is the:
A Fault throw
B Bed thickness
C Fold wavelength
D Axial trace
Answer: C. Fold wavelength. Fold wavelength measures spacing between corresponding points on successive folds.
An open fold generally has a:
A Wide interlimb angle
B Very narrow hinge
C Horizontal fault plane
D Vertical fault scarp
Answer: A. Wide interlimb angle. Open folds have a relatively large angle between their limbs.
A fold produced as layers move over a thrust ramp is a:
A Drag fold
B Fault-bend fold
C Chevron fold
D Monocline
Answer: B. Fault-bend fold. A thrust sheet moving over a ramp can bend layers into a fault-bend fold.
A fold forming above an advancing blind-thrust tip is a:
A Fault-propagation fold
B Rollover anticline
C Parasitic fold
D Dome structure
Answer: A. Fault-propagation fold. Fault-propagation folds develop above the advancing tip of a thrust fault.
A thrust fault that does not reach the ground surface is:
A Surface rupture
B Normal fault
C Joint plane
D Blind thrust
Answer: D. Blind thrust. A blind thrust terminates below the surface, often dying upward into a fold.
A weak horizon that separates deformation above and below can act as a:
A Fault scarp
B Décollement
C Fold hinge
D Strike line
Answer: B. Décollement. A décollement is a detachment horizon that permits different deformation styles above and below.
Closely spaced, overlapping thrust faults create an:
A Open basin
B Joint pattern
C Imbricate stack
D Transform zone
Answer: C. Imbricate stack. Imbricate thrusts are overlapping subsidiary faults that stack rock slices.
A stack of thrust-bounded rock slices can form a:
A Duplex
B Horst
C Monocline
D Dome
Answer: A. Duplex. A duplex is a set of imbricate thrust slices bounded by floor and roof thrusts.
Sediments deposited while deformation is active are:
A Basal till
B Syntectonic strata
C Eolian dunes
D Lava flows
Answer: B. Syntectonic strata. Syntectonic strata accumulate during active tectonic deformation.
Beds that thicken toward an active fault during deposition are:
A Older basement
B Fault breccia
C Fold limbs
D Growth strata
Answer: D. Growth strata. Growth strata record deposition during movement, often thickening toward an active fault.
Tilted, eroded beds overlain by flat layers mark an:
A Fault scarp
B Axial trace
C Angular unconformity
D Intrusive contact
Answer: C. Angular unconformity. An angular unconformity separates tilted older strata from younger beds with a different orientation.
A fault cutting across folded layers formed:
A Before deposition
B After folding
C During weathering
D With no movement
Answer: B. After folding. A fault that cuts folded beds is younger than the folding it cross-cuts.
If a later fold bends an existing fault surface, folding occurred:
A After faulting
B Before faulting
C Before all deposition
D Without strain
Answer: A. After faulting. A structure that bends a fault must postdate that fault.
A basin mainly bounded by one major normal fault is a:
A Horst
B Anticlinorium
C Dome
D Half-graben
Answer: D. Half-graben. A half-graben is an asymmetric basin commonly associated with a major normal fault.
The cross-section of a half-graben is commonly:
A Perfectly circular
B Flat and uniform
C Asymmetric
D Radially folded
Answer: C. Asymmetric. A half-graben has an asymmetric geometry controlled by its principal normal fault.
A fold-and-thrust belt mainly records crustal:
A Shortening
B Extension
C Thermal expansion
D Chemical alteration
Answer: A. Shortening. Fold-and-thrust belts develop through shortening and thrust displacement.
Paleozoic rocks in the Appalachian Valley and Ridge were extensively:
A Only weathered
B Folded and thrust-faulted
C Never deformed
D Melted completely
Answer: B. Folded and thrust-faulted. USGS describes the province’s Paleozoic strata as folded and thrust-faulted.
Long parallel ridges in folded terrain can result from:
A Uniform deposition
B Daily tides
C Differential erosion
D Magnetic reversals
Answer: C. Differential erosion. Erosion exposes contrasting rock layers that can form parallel ridges and valleys.
The main mountain-building event linked to Appalachian folding was the:
A Nevadan orogeny
B Caledonian rifting
C Hawaiian volcanism
D Alleghanian orogeny
Answer: D. Alleghanian orogeny. USGS regional studies link major Appalachian folding and thrusting to the Alleghanian orogeny.
A thrust changing stratigraphic level perpendicular to strike forms a:
A Frontal ramp
B Lateral ramp
C Fault window
D Rift shoulder
Answer: A. Frontal ramp. A frontal ramp changes décollement level across the structural strike direction.