Difficulty: Easy & Basic
In a structural dome, bedding usually dips:
A Toward the center
B Only northward
C Along a river
D Away from the center
Answer: D. Away from the center. Dome strata generally dip outward from the structural high.
In a structural basin, bedding usually dips:
A Away from the center
B Toward the center
C Only eastward
D Toward a ridge
Answer: B. Toward the center. Basin strata dip inward toward the structural low.
A fold with similar limb dips in opposite directions is:
A Symmetrical
B Asymmetrical
C Overturned
D Recumbent
Answer: A. Symmetrical. A symmetrical fold has limbs with broadly similar dips on opposite sides.
A fold with one limb steeper than the other is:
A Symmetrical
B Isoclinal
C Asymmetrical
D Recumbent
Answer: C. Asymmetrical. Unequal limb dips make a fold asymmetrical.
A fold whose limbs are nearly parallel is:
A Open
B Gentle
C Monoclinal
D Isoclinal
Answer: D. Isoclinal. Isoclinal folds have nearly parallel limbs.
Straight limbs meeting at sharp hinges describe a:
A Chevron fold
B Open fold
C Dome
D Basin
Answer: A. Chevron fold. Chevron folds have angular hinges and relatively straight limbs.
A fold with one limb rotated beyond vertical is:
A Symmetrical
B Overturned
C Open
D Upright
Answer: B. Overturned. Overturning rotates one limb past vertical.
A fold with an almost horizontal axial plane is:
A Upright
B Open
C Recumbent
D Plunging
Answer: C. Recumbent. Recumbent folds have axial surfaces that are nearly horizontal.
When fold age is unknown, an upward arch is an:
A Anticline
B Syncline
C Synform
D Antiform
Answer: D. Antiform. Antiform describes upward-convex geometry without specifying the age of core beds.
When fold age is unknown, a downward trough is a:
A Synform
B Syncline
C Antiform
D Anticline
Answer: A. Synform. Synform describes downward-concave geometry without specifying the age of core beds.
Rock layers bending without breaking show mainly:
A Brittle fracture
B Surface erosion
C Ductile deformation
D Chemical weathering
Answer: C. Ductile deformation. Folding is commonly associated with ductile bending of rock layers.
In geology, stress is force applied per:
A Unit volume
B Unit area
C Unit time
D Unit length
Answer: B. Unit area. Stress is force divided by the area over which it acts.
The angle of an inclined plane from horizontal is its:
A Strike
B Trend
C Plunge
D Dip
Answer: D. Dip. Dip measures the angle at which a plane inclines from horizontal.
The compass direction of a plane’s horizontal line is its:
A Strike
B Dip
C Plunge
D Throw
Answer: A. Strike. Strike describes the compass orientation of a horizontal line on a plane.
Where a fault intersects Earth’s surface is its:
A Fold axis
B Axial plane
C Fault trace
D Bedding plane
Answer: C. Fault trace. The fault trace is the mapped intersection of a fault with the ground surface.
The vertical component of fault separation is called:
A Heave
B Throw
C Strike
D Plunge
Answer: B. Throw. Throw is the vertical component of separation across a fault.
The horizontal component of fault separation is called:
A Heave
B Throw
C Dip
D Hinge
Answer: A. Heave. Heave describes the horizontal component of fault separation.
Polished, grooved marks on a fault surface are:
A Fossils
B Ripple marks
C Mud cracks
D Slickensides
Answer: D. Slickensides. Slickensides are striations or polished marks produced by movement along a fault.
Fine, crushed material in a fault zone is often called:
A Ridge sand
B Fault gouge
C Volcanic ash
D River silt
Answer: B. Fault gouge. Fault gouge is finely ground material formed by movement in a fault zone.
Coarse angular fragments along a fault form:
A Loess
B Till
C Fault breccia
D Conglomerate
Answer: C. Fault breccia. Fault breccia consists of angular fragments produced by brittle crushing along a fault.
If the far block shifts left across a strike-slip fault, it is:
A Right-lateral
B Normal
C Reverse
D Left-lateral
Answer: D. Left-lateral. Left-lateral motion means the opposite block appears to move left.
If the far block shifts right across a strike-slip fault, it is:
A Left-lateral
B Normal
C Right-lateral
D Reverse
Answer: C. Right-lateral. Right-lateral motion means the opposite block appears to move right.
A fold made of several parallel arches and troughs is a:
A Fold train
B Single joint
C Fault scarp
D Rift basin
Answer: A. Fold train. A fold train is a sequence of related folds.
The surface that divides a fold as a geometric plane is the:
A Fault trace
B Axial plane
C Strike line
D Scarp face
Answer: B. Axial plane. The axial plane connects hinge lines through a fold’s limbs.
On a map, the line where an axial plane meets ground is the:
A Axial trace
B Fault trace
C Fold limb
D Fault throw
Answer: A. Axial trace. An axial trace is the surface intersection of a fold’s axial plane.