At balance, why does a DC potentiometer avoid loading the cell being tested?
A It shorts the cell
B It draws no test current
C It adds a shunt
D It measures resistance
Answer: B. It draws no test current. At null, no current is taken from the cell under test.
Two unknown EMFs balance at lengths 30 cm and 60 cm on the same uniform wire. What is their ratio?
A 2:1
B 1:2
C 1:4
D 4:1
Answer: B. 1:2. With the same potential gradient, each EMF is proportional to balance length.
Which bridge is commonly used to measure inductance with a standard capacitor?
A Maxwell bridge
B Wheatstone bridge
C Schering bridge
D Kelvin bridge
Answer: A. Maxwell bridge. A Maxwell inductance-capacitance bridge compares the unknown inductance with a standard capacitance.
Which AC bridge measures capacitance and dielectric loss?
A Maxwell bridge
B Kelvin bridge
C Schering bridge
D Wheatstone bridge
Answer: C. Schering bridge. The Schering bridge is used for capacitance and insulation dielectric-loss measurements.
Which bridge is suited to a high-Q inductor?
A Wien bridge
B Kelvin bridge
C Hay bridge
D Schering bridge
Answer: C. Hay bridge. The Hay bridge is a modification of Maxwell bridge suited to high-Q inductors.
Which bridge can determine frequency using a resistor-capacitor network?
A Kelvin bridge
B Maxwell bridge
C Schering bridge
D Wien bridge
Answer: D. Wien bridge. At balance, the Wien bridge frequency depends on its RC arms.
A bonded strain gauge senses mechanical strain through which electrical change?
A Resistance change
B Frequency doubling
C Open-circuit voltage
D Inductance cancellation
Answer: A. Resistance change. Strain changes the gauge length and area, changing its resistance.
Gauge factor equals fractional resistance change divided by what?
A Applied voltage
B Supply frequency
C Load current
D Mechanical strain
Answer: D. Mechanical strain. Gauge factor is (ΔR/R)/ε, where ε is mechanical strain.
What electrical property changes in a typical resistance temperature detector?
A Resistance
B Inductance only
C Capacitance only
D Frequency only
Answer: A. Resistance. An RTD uses the predictable temperature dependence of metal resistance.
A thermocouple develops voltage through which effect?
A Hall effect
B Skin effect
C Photoelectric effect
D Seebeck effect
Answer: D. Seebeck effect. A temperature difference between dissimilar conductors produces thermoelectric EMF.
An LVDT primarily measures which quantity?
A Light intensity
B Insulation resistance
C Angular frequency
D Linear displacement
Answer: D. Linear displacement. The differential secondary voltages change with core position.
A piezoelectric sensor is especially suitable for which measurement?
A Dynamic vibration
B Steady DC resistance
C Static temperature
D Long-term DC force
Answer: A. Dynamic vibration. Charge leakage makes piezoelectric sensors particularly useful for changing forces and vibration.
A Hall-effect sensor responds directly to which field?
A Gravitational field
B Magnetic field
C Acoustic field
D Thermal field
Answer: B. Magnetic field. The Hall voltage arises from moving charge carriers in a magnetic field.
Which device converts incident light into an electrical signal?
A Shunt resistor
B Moving-iron meter
C Photodiode
D Current transformer
Answer: C. Photodiode. A photodiode produces light-dependent current under appropriate bias.
How many distinct digital codes can an ideal 8-bit ADC produce?
A 256
B 8
C 128
D 1024
Answer: A. 256. An n-bit ADC has 2^n possible codes, and 2^8=256.
For a 0–10 V ideal 10-bit ADC, approximately how wide is one quantization step?
A 0.977 mV
B 97.7 mV
C 1 V
D 9.77 mV
Answer: D. 9.77 mV. Ten volts divided by 1024 codes is about 9.77 mV per step.
Averaging many readings mainly reduces which type of measurement error?
A Fixed calibration offset
B Zero-mean random noise
C Wrong scale factor
D Broken sensor
Answer: B. Zero-mean random noise. Independent random fluctuations tend to cancel in the average.
Why must a measuring system have adequate bandwidth?
A To increase resistance
B To remove grounding
C To follow signal changes
D To double resolution
Answer: C. To follow signal changes. Insufficient bandwidth attenuates or distorts changing signals.
An unwanted current flows through multiple instrument grounds. What can this cause?
A Perfect isolation
B Ground-loop interference
C Zero offset always
D Higher quantization bits
Answer: B. Ground-loop interference. Multiple ground paths can pick up interference and create voltage errors.
In a four-wire resistance measurement, what do the separate sense leads carry ideally?
A Negligible current
B Full load current
C Half source current
D AC only
Answer: A. Negligible current. High-impedance voltage-sense leads draw very little current, reducing lead-drop error.
What is the main purpose of guarding in high-resistance measurements?
A Increase meter burden
B Short the sample
C Change AC frequency
D Reduce leakage error
Answer: D. Reduce leakage error. A driven guard diverts stray leakage currents away from the measurement path.
Which source is usually applied by an insulation-resistance tester?
A High DC voltage
B Low AC current
C Radio-frequency pulses
D Three-phase power
Answer: A. High DC voltage. A megohmmeter applies a DC test voltage and infers insulation resistance from leakage current.
What is compared in a null measurement?
A Peak against RMS
B Current against frequency
C Balance against reference
D Power against energy
Answer: C. Balance against reference. A null method adjusts a known quantity until the detector indicates zero difference.
A 10× probe is connected, but the oscilloscope channel is set to 1×. How is displayed voltage affected?
A Ten times too high
B Unaffected
C Ten times too low
D Zero always
Answer: C. Ten times too low. Without 10× compensation in the channel setting, the displayed voltage is one tenth of the actual signal.
In a digital meter, what does resolution describe?
A Maximum safe voltage
B Smallest indicated increment
C Calibration date
D Battery lifetime
Answer: B. Smallest indicated increment. Resolution is the smallest change that the display can distinguish.