Which part of the power system delivers electricity to end users?
A Generating station
B Fuel supply chain
C Distribution network
D Turbine governor
Answer: C. Distribution network. Distribution is the final electrical stage between substations and consumers.
In many Indian systems, which voltage is commonly used for primary distribution?
A 415 V
B 33 V
C 11 kV
D 400 kV
Answer: C. 11 kV. 11 kV is a widely used primary distribution level, though utilities also use other voltages.
A typical three-phase low-voltage distribution supply is what?
A 415/240 V
B 11/6.6 kV
C 220/110 kV
D 33/11 kV
Answer: A. 415/240 V. A common LV system supplies about 415 V line-to-line and 240 V phase-to-neutral.
What does a feeder mainly carry from a substation?
A Consumer meter readings
B Fuel to generators
C Water to turbines
D Power to distribution areas
Answer: D. Power to distribution areas. Feeders transport power from the substation toward load areas.
Which conductor section has many customer service connections tapped along it?
A Transmission bus
B Generator lead
C Ground wire
D Distributor
Answer: D. Distributor. A distributor supplies local loads through multiple tapping points.
The service main connects the distributor to which point?
A Consumer premises
B Generating station
C Transmission tower
D Power plant boiler
Answer: A. Consumer premises. Service conductors deliver electricity from the local network to a customer.
A radial distribution network normally has how many supply paths to each load?
A One main path
B Two independent paths
C No source path
D Four meshed paths
Answer: A. One main path. Radial feeders have a single direction of supply under normal operation.
A ring-main arrangement can improve what compared with a simple radial feeder?
A Supply reliability
B Fuel efficiency
C Generator speed
D Conductor conductivity
Answer: A. Supply reliability. A load section can sometimes be fed from the other side of the ring.
An interconnected distribution network offers what compared with a single radial path?
A Multiple supply paths
B Lower voltage always
C No protection needs
D Zero fault current
Answer: A. Multiple supply paths. Meshed connections can provide alternate paths, with more complex protection.
What is the main role of a distribution transformer?
A Generate electricity
B Step down voltage
C Change system frequency
D Measure consumer energy
Answer: B. Step down voltage. It reduces primary distribution voltage to a utilization level.
A pole-mounted transformer is commonly installed where?
A Overhead distribution line
B Underground cable joint
C Generator rotor
D Control room desk
Answer: A. Overhead distribution line. It is mounted on a pole structure near local loads.
What provides a common connection point for substation circuits?
A Service drop
B Fuse link
C Guy wire
D Busbar
Answer: D. Busbar. Busbars collect and distribute power among incoming and outgoing circuits.
An outgoing substation feeder usually supplies what?
A Only a generator field
B A distribution area
C Fuel storage
D Cooling water
Answer: B. A distribution area. Each feeder carries power from the bus to a separate network section.
Why does distribution demand change during a day?
A Line length changes hourly
B Customer use varies
C Poles rotate faster
D Voltage becomes DC
Answer: B. Customer use varies. Residential, commercial and industrial loads vary with time.
Peak demand is the what in a specified period?
A Minimum voltage
B Average frequency
C Maximum load
D Transformer oil level
Answer: C. Maximum load. Peak demand is the highest coincident load in the period.
Compared with overhead construction, underground distribution generally offers what?
A Lower installation cost always
B No insulation needed
C Zero capacitance
D Less visual exposure
Answer: D. Less visual exposure. Underground cables are less visible but usually cost more to install and repair.
Insulators on an overhead distributor separate live conductors from what?
A Other loads always
B Grounded supports
C Transformer oil
D Neutral current
Answer: B. Grounded supports. They prevent current leakage to poles and crossarms.
A fuse primarily protects a distribution branch against what?
A Low power factor
B High frequency
C Overcurrent
D Poor load balance only
Answer: C. Overcurrent. A fuse melts when excessive current persists.
What does an automatic recloser do after many temporary feeder faults?
A Steps down voltage
B Measures energy
C Changes phase order
D Opens and recloses
Answer: D. Opens and recloses. It interrupts fault current and then attempts restoration after a short interval.
A sectionalizer usually opens after what happens upstream?
A It interrupts fault current itself
B Fault current is interrupted
C Voltage is doubled
D A meter resets
Answer: B. Fault current is interrupted. It counts fault operations and isolates a section during the upstream device’s dead time.
Protective coordination aims to make which device operate first for a local fault?
A Every breaker together
B The generator first
C No device
D Nearest downstream device
Answer: D. Nearest downstream device. Selective coordination isolates the smallest practical faulted section.
A distribution substation commonly connects distribution feeders to which upstream system?
A Consumer appliance
B Subtransmission network
C Fuel pipeline
D Communication satellite
Answer: B. Subtransmission network. It transforms voltage and supplies local feeder circuits.
A shunt capacitor bank near inductive loads can improve what?
A Conductor sag
B Fuel quality
C Power factor
D System pole count
Answer: C. Power factor. Local capacitive VARs offset part of the inductive demand.
A step voltage regulator is used mainly to control what?
A Line frequency
B Conductor material
C Feeder voltage
D Customer energy units
Answer: C. Feeder voltage. It adjusts voltage to keep customer supply within an acceptable range.
Technical distribution losses arise mainly from what?
A Electrical resistance
B Unpaid bills only
C Meter reading delays
D Customer demand forecasts
Answer: A. Electrical resistance. Current through wires and transformers causes I²R heating.