The geometric neutral axis lies where relative to adjacent main poles?
A At each pole center
B Midway between them
C Along shaft axis
D Inside a brush
Answer: B. Midway between them. The geometric neutral is midway between neighboring pole centers.
At the magnetic neutral plane, the instantaneous induced EMF in a passing armature conductor is ideally what?
A Maximum positive
B Maximum negative
C Equal to supply
D Zero
Answer: D. Zero. Conductors crossing the magnetic neutral zone cut essentially no resultant flux.
During commutation, a coil is temporarily short-circuited by what?
A A pole shoe
B A brush
C A bearing
D The shaft
Answer: B. A brush. The brush bridges neighboring commutator segments while coil current reverses.
Reactance voltage in a commutating coil arises primarily from what?
A Brush friction
B Field saturation only
C Self-induction
D Windage
Answer: C. Self-induction. Changing current in the shorted coil induces a voltage opposing its reversal.
Why do relatively high-resistance carbon brushes aid commutation?
A Eliminate all losses
B Double field flux
C Raise rotor speed
D Limit short-circuit current
Answer: D. Limit short-circuit current. Contact resistance helps limit circulating current during segment overlap.
A 3-point starter no-voltage coil is in series with which circuit?
A Armature resistance only
B Bearing circuit
C Shunt-field circuit
D Series compensator only
Answer: C. Shunt-field circuit. Its hold-on coil follows field current, which can make deep field weakening trip it.
Severe field weakening may release a 3-point starter because what current falls?
A No-voltage coil current
B Armature current always
C Brush current only
D Load current to zero
Answer: A. No-voltage coil current. The hold-on magnet weakens as current in its field-linked path decreases.
In a 4-point starter, the no-voltage coil is connected how relative to the field?
A In series with field
B Across each commutator
C Independently across supply
D In the shaft
Answer: C. Independently across supply. Its separate supply path avoids nuisance release during field control.
Armature-resistance speed control wastes power chiefly as what?
A Magnetic energy storage
B Heat in added resistor
C Acoustic energy only
D Useful shaft power
Answer: B. Heat in added resistor. The inserted resistor dissipates I²R loss.
With rated armature voltage, reducing field flux usually provides what speed range?
A Above base speed
B Below zero speed
C Only exact base speed
D Synchronous speed
Answer: A. Above base speed. Flux weakening increases speed above the base-speed region.
For plugging a DC shunt motor, which polarity is reversed relative to field?
A Both armature and field
B Mechanical load only
C Starter resistance only
D Armature supply
Answer: D. Armature supply. Reversing armature supply while leaving field unchanged creates opposing torque.
Why is a series resistor used during plugging?
A Limit large current
B Increase efficiency to 100%
C Remove the field
D Store braking energy
Answer: A. Limit large current. Supply and rotational EMF may add, so resistance restrains armature current.
In dynamic braking, mechanical energy is mainly dissipated where?
A Braking resistor
B Supply transformer
C Field winding only
D Shaft bearing only
Answer: A. Braking resistor. The rotating machine generates current into a resistor after armature supply is removed.
Regenerative braking returns power to the supply when back EMF is how relative to supply voltage?
A Smaller
B Exactly zero
C Opposite frequency
D Greater
Answer: D. Greater. Back EMF exceeding terminal voltage reverses armature current and returns electrical power.
If speed doubles at constant flux, how does back EMF change ideally?
A It halves
B It quadruples
C It doubles
D It stays zero
Answer: C. It doubles. Back EMF is proportional to flux times speed.
A DC motor at 1200 rpm has 100 V back EMF at fixed flux. At 600 rpm, what is back EMF?
A 25 V
B 100 V
C 50 V
D 200 V
Answer: C. 50 V. Halving speed at unchanged flux halves the generated back EMF.
At fixed voltage and field, a slowing motor draws more armature current because what falls?
A Back EMF
B Armature resistance
C Supply voltage
D Pole count
Answer: A. Back EMF. Ia=(V−Eb)/Ra, so a smaller Eb means larger current.
As load torque increases on a DC series motor, speed generally does what?
A Falls
B Rises without bound
C Stays exactly fixed
D Reverses immediately
Answer: A. Falls. The higher armature current and stronger flux accompany a lower operating speed.
A DC shunt motor draws 12 A from supply and 2 A in its shunt field. What is armature current?
A 2 A
B 10 A
C 12 A
D 14 A
Answer: B. 10 A. Line current splits into shunt-field and armature branches, so Ia=12−2=10 A.
A shunt generator supplies 10 A load and 2 A field current. What armature current does it generate?
A 8 A
B 10 A
C 2 A
D 12 A
Answer: D. 12 A. Generator armature current supplies both load and shunt field: Ia=10+2=12 A.
How is shaft mechanical power related to torque T and angular speed ω?
A T/ω
B Tω
C ω/T
D T+ω
Answer: B. Tω. Rotational mechanical power equals torque times angular speed.
A motor shaft delivers 10 N·m at 60 rad/s. What is shaft power?
A 6 W
B 60 W
C 600 W
D 3600 W
Answer: C. 600 W. P=Tω=10×60=600 W.
A DC generator has Eg=200 V, IaRa=10 V and total brush drop=2 V. What is terminal voltage?
A 190 V
B 188 V
C 202 V
D 212 V
Answer: B. 188 V. Terminal voltage is 200−10−2=188 V.
Which connection reduces circulating currents between parallel paths of a lap winding?
A Equalizer rings
B Wave winding only
C Shaft bearings
D Brush insulation
Answer: A. Equalizer rings. Equalizer connections link points of equal nominal potential to accommodate unequal pole flux.
For a motor at fixed flux, which change reverses developed torque?
A Double armature current
B Increase shaft load
C Reduce armature resistance
D Reverse armature current
Answer: D. Reverse armature current. T is proportional to ΦIa, so reversing Ia reverses torque sign.