A conventional DC machine can act as a motor or generator. What does this illustrate?
A Only AC operation
B Reversible energy conversion
C Constant-speed operation
D Lossless conversion
Answer: B. Reversible energy conversion. The same electromagnetic structure converts electrical to mechanical power or the reverse.
In a conventional brushed DC machine, which part rotates?
A Yoke
B Armature
C Main pole
D Field frame
Answer: B. Armature. The armature and commutator are mounted on the rotor shaft.
What is the yoke of a DC machine mainly used for?
A Commutation only
B Armature switching
C Shaft insulation
D Support and flux return
Answer: D. Support and flux return. The yoke supports the poles and provides a low-reluctance return path for main flux.
Which part establishes the main magnetic field in a wound-field DC machine?
A Brush holder
B Commutator bars
C Field poles
D Bearings
Answer: C. Field poles. Excited field windings on the poles produce the main flux.
Why is the armature core laminated?
A Increase brush pressure
B Eliminate copper loss
C Reduce eddy-current loss
D Raise field resistance
Answer: C. Reduce eddy-current loss. Thin insulated laminations restrict circulating eddy currents in the rotating core.
What is the commutator action in a DC generator?
A Mechanical rectification
B Voltage transformation
C Frequency multiplication
D Magnetic shielding
Answer: A. Mechanical rectification. Commutator segments reverse coil connections so the external output remains unidirectional.
How is current transferred between the rotating commutator and external circuit?
A Through pole shoes
B Through bearings
C Through air gap
D Through brushes
Answer: D. Through brushes. Stationary brushes make sliding electrical contact with commutator segments.
The induced EMF in an armature conductor follows which principle?
A Faraday induction
B Coulomb friction
C Joule heating
D Capacitive charging
Answer: A. Faraday induction. Motion through magnetic flux changes linkage and induces an EMF.
At fixed construction, generated EMF is proportional to which two quantities?
A Resistance and torque
B Flux and speed
C Current and friction
D Brush area and load
Answer: B. Flux and speed. The DC machine EMF equation contains flux per pole and rotational speed.
A generator doubles speed with unchanged flux. What happens to generated EMF ideally?
A It halves
B It doubles
C It stays zero
D It quadruples
Answer: B. It doubles. Generated EMF is directly proportional to speed at fixed flux.
In the DC machine EMF equation E=PΦZN/(60A), what does A denote?
A Armature area
B Air-gap length
C Ampere turns
D Parallel armature paths
Answer: D. Parallel armature paths. A is the number of parallel paths through the armature winding.
For a simplex lap winding with P poles, how many parallel paths are there?
A P
B 2
C P/2
D 2P
Answer: A. P. A simplex lap winding has as many parallel paths as poles.
For a simplex wave winding, how many parallel paths are there?
A P
B 2P
C PΒ²
D 2
Answer: D. 2. A simplex wave winding has two parallel paths independent of pole count.
A four-pole simplex lap armature has how many parallel paths?
A 1
B 4
C 2
D 8
Answer: B. 4. For simplex lap winding, A=P=4.
Which winding generally suits higher current at lower voltage?
A Lap winding
B Wave winding
C Field winding
D Compensating winding
Answer: A. Lap winding. More parallel paths in a lap winding share the armature current.
How is the field of a separately excited DC generator supplied?
A Only its own terminal
B Series load current
C Mechanical shaft
D Independent DC source
Answer: D. Independent DC source. Its field winding receives power from a separate supply.
Where is the shunt field connected in a self-excited shunt generator?
A Across its terminals
B In series with load
C Across each brush
D Across the bearings
Answer: A. Across its terminals. The shunt field is connected in parallel with the armature terminals.
Where is the series field connected in a series DC generator?
A In series with load
B Across the armature
C Across the field rheostat
D In the shaft
Answer: A. In series with load. The series winding carries the armature and load current.
What enables a self-excited DC generator to start voltage buildup?
A Residual magnetism
B Zero field resistance
C Open brushes
D Infinite speed
Answer: A. Residual magnetism. Residual pole flux produces an initial EMF that feeds the field.
The open-circuit characteristic of a DC generator plots generated EMF against what at fixed speed?
A Load torque
B Armature resistance
C Field current
D Brush wear
Answer: C. Field current. The OCC is the magnetization curve versus field current at constant speed.
Above a certain shunt-field resistance, voltage may fail to build. What is that threshold called?
A Armature resistance
B Brush contact resistance
C Insulation resistance
D Critical field resistance
Answer: D. Critical field resistance. The critical resistance is the maximum field-circuit resistance for self-excitation at a given speed.
Armature reaction primarily does what to the main field?
A Eliminates all losses
B Raises shaft speed
C Distorts its distribution
D Removes commutator
Answer: C. Distorts its distribution. Armature current creates its own field, changing the resultant air-gap flux.
Interpoles are mainly installed to improve what?
A Shaft lubrication
B Commutation
C Voltage insulation
D Mechanical balancing
Answer: B. Commutation. Interpoles provide a reversing field in the commutation zone.
Compensating windings counter which effect under pole faces?
A Bearing friction
B Core hysteresis
C Armature reaction
D Windage
Answer: C. Armature reaction. They oppose the armature-produced cross-magnetizing field under pole faces.
Ignoring brush drop, which expression gives generator terminal voltage?
A Eg plus IaRa
B IaRa only
C Eg minus IaRa
D Eg times Ia
Answer: C. Eg minus IaRa. The armature resistance drop reduces terminal voltage below generated EMF under load.