As load current rises, why does a DC shunt generator terminal voltage usually fall?
A Increasing residual magnetism
B Internal drop and reaction
C Falling armature resistance
D Infinite field current
Answer: B. Internal drop and reaction. Armature resistance drop and armature reaction reduce terminal voltage.
At light load, a DC series generator voltage tends to rise mainly because of what?
A Decreasing armature current
B Falling pole count
C Increasing series-field current
D Zero magnetic flux
Answer: C. Increasing series-field current. Load current strengthens its series field before saturation dominates.
A cumulative compound generator uses its series field to do what?
A Oppose the shunt field
B Short the armature
C Remove residual magnetism
D Aid the shunt field
Answer: D. Aid the shunt field. The series field reinforces the shunt field as load increases.
An overcompounded generator has full-load terminal voltage relative to no-load voltage that is what?
A Lower
B Always zero
C Exactly alternating
D Higher
Answer: D. Higher. Overcompounding raises full-load terminal voltage above its no-load value.
A level-compounded generator has approximately what full-load voltage relative to no-load voltage?
A Twice as high
B Zero
C The same
D Opposite polarity
Answer: C. The same. Series excitation compensates internal drop to keep the two terminal voltages similar.
A differential compound generator has its series field connected to do what?
A Oppose shunt flux
B Aid shunt flux
C Reverse armature
D Increase pole count
Answer: A. Oppose shunt flux. Its series winding weakens the net field as load current increases.
In a long-shunt compound generator, where is the shunt field connected?
A Across armature only
B Across output terminals
C In series with load
D Across interpoles only
Answer: B. Across output terminals. The long-shunt field spans the armature and series-field combination.
In a short-shunt compound generator, the shunt field is connected across what?
A Armature only
B Entire output terminals
C Series field only
D Load only
Answer: A. Armature only. The short-shunt field is directly across the armature.
Why does an open-circuit magnetization curve flatten at high field current?
A Falling rotor speed
B Open-circuit current
C Brush wear only
D Magnetic saturation
Answer: D. Magnetic saturation. The iron approaches saturation, so extra field current yields less additional flux.
Loss of residual magnetism can prevent what in a self-excited generator?
A Voltage buildup
B Shaft rotation
C Armature resistance
D Copper heating
Answer: A. Voltage buildup. Without residual flux, the initial generated voltage may be too small for field buildup.
For self-excitation at a given speed, shunt-field resistance should be how relative to critical resistance?
A Above it
B Exactly infinite
C Below it
D Always zero
Answer: C. Below it. A field resistance below the critical value permits the voltage buildup intersection.
For a fixed shunt-field resistance, critical speed is the minimum speed required for what?
A Zero friction
B Commutator reversal
C Voltage buildup
D Rated torque
Answer: C. Voltage buildup. Below critical speed, the OCC cannot sustain self-excitation with that field resistance.
Sparking at DC machine brushes is a sign of poor what?
A Shaft alignment only
B Field insulation only
C Iron lamination
D Commutation
Answer: D. Commutation. Incomplete current reversal in a shorted coil can cause sparking.
Armature reaction moves the magnetic neutral plane mainly as which quantity changes?
A Bearing size
B Brush material
C Shaft diameter
D Armature current
Answer: D. Armature current. The armature field strength varies with current and shifts the resultant neutral zone.
How are interpole windings generally connected?
A In series with armature
B Across shunt field
C Open-circuit
D Across each brush
Answer: A. In series with armature. Series connection makes the correcting field track armature current.
Compensating windings are generally excited by which current?
A Bearing current
B Armature current
C No-load leakage
D External AC only
Answer: B. Armature current. Their series connection makes compensation follow armature loading.
Armature copper loss varies approximately with what?
A Ia/Ra
B Ia²Ra
C Speed only
D Flux only
Answer: B. Ia²Ra. Resistive heating in the armature winding is current squared times resistance.
Which pair forms the main iron or core losses?
A Brush and bearing losses
B Copper and windage
C Field and shunt losses
D Hysteresis and eddy currents
Answer: D. Hysteresis and eddy currents. Alternating flux in the rotating armature produces hysteresis and eddy-current losses.
Which losses are mechanical rotational losses?
A Armature I²R
B Friction and windage
C Field I²R
D Eddy currents only
Answer: B. Friction and windage. Bearing and brush friction plus air resistance consume mechanical power.
How is machine efficiency defined?
A Output divided by input
B Input divided by output
C Loss divided by speed
D Current divided by flux
Answer: A. Output divided by input. Efficiency is the useful output power divided by input power.
A machine delivers 8 kW from 10 kW input. What is its efficiency?
A 80%
B 20%
C 125%
D 8%
Answer: A. 80%. 8/10=0.8, so efficiency is 80%.
For maximum efficiency, variable losses approximately equal what?
A Terminal voltage
B Rotor speed
C Constant losses
D Output torque
Answer: C. Constant losses. At the optimum load, variable copper loss balances the constant losses.
A direct load test determines efficiency using what?
A Only no-load current
B Only brush count
C Measured input and output
D Only field resistance
Answer: C. Measured input and output. Input and output power are measured under actual loading.
Swinburne’s test is primarily a no-load method for estimating efficiency of which machine?
A DC series only
B DC shunt machine
C Induction generator
D Synchronous condenser
Answer: B. DC shunt machine. A no-load shunt-machine test estimates constant losses and predicts efficiency at load.
Hopkinson’s test uses two similar DC machines coupled so supply mainly covers what?
A Their combined losses
B Both rated outputs
C Only field resistance
D Zero power
Answer: A. Their combined losses. Power circulates between motor and generator, with supply making up losses.