Which reactant fixes the maximum possible amount of product in a complete single reaction?
A Excess reactant
B Limiting reactant
C Inert gas
D Solvent alone
Answer: B. Limiting reactant. Reaction stoichiometry determines which available reactant runs out first and limits product.
Write enthalpy H in terms of internal energy U, pressure P and volume V.
A H = U + PV
B H = U/PV
C H = U β PV
D H = PV β U
Answer: A. H = U + PV. Enthalpy adds the pressureβvolume term to internal energy.
In an ideal gas mixture at 200 kPa, component A has mole fraction 0.25. What is its partial pressure?
A 150 kPa
B 800 kPa
C 50 kPa
D 25 kPa
Answer: C. 50 kPa. Partial pressure equals mole fraction times total pressure.
Which quantity is the ratio of reactant consumed to that reactant fed?
A Molar concentration
B Mass density
C Specific volume
D Fractional conversion
Answer: D. Fractional conversion. Fractional conversion measures the part of a specified reactant feed that reacts.
For an adiabatic boundary, which transfer is zero?
A Heat transfer
B All work transfer
C Potential energy
D Mass flow in every case
Answer: A. Heat transfer. Adiabatic describes absence of heat transfer. Other transfers may occur depending on the system.
Relative humidity compares water vapour partial pressure with what at the same temperature?
A Oxygen partial pressure
B Water saturation pressure
C Total gas pressure
D Absolute zero pressure
Answer: B. Water saturation pressure. Relative humidity is the ratio of actual water partial pressure to the saturation value at that temperature.
For heating a material that does not change phase, which property relates heat use to temperature change at constant pressure?
A Partial pressure
B Relative density
C Heat capacity
D Mole percentage only
Answer: C. Heat capacity. For a specified amount, heat capacity relates sensible enthalpy change to a temperature change.
For A β 2B, how many moles of B form when 3 mol A react completely?
A 9 mol
B 1.5 mol
C 3 mol
D 6 mol
Answer: D. 6 mol. The stoichiometric equation produces two moles of B for every mole of A consumed.
At fixed volume and moles, an ideal gas absolute temperature doubles. What happens to its pressure?
A It stays fixed
B It quadruples
C It doubles
D It halves
Answer: C. It doubles. The ideal gas equation makes pressure proportional to absolute temperature at fixed moles and volume.
Degrees of freedom are found by subtracting which count from the number of unknown variables?
A Independent equations
B Every reaction coefficient
C Previously measured values twice
D Number of units only
Answer: A. Independent equations. Degrees of freedom count unknown variables still undetermined after independent equations or specifications are applied.
What does the coefficient 2 before Hβ in a balanced reaction equation represent?
A Two mΒ³ in every case
B Two percentage points
C Two kilograms of hydrogen
D Two molar stoichiometric units
Answer: D. Two molar stoichiometric units. Balanced equation coefficients give relative mole amounts consumed or produced.
Sensible heating of a single-phase stream changes what directly?
A Chemical identity always
B Molecular mass
C Number of elements
D Temperature
Answer: D. Temperature. Sensible heat changes temperature without requiring a phase change.
If pressure is 30 kPa gauge and atmospheric pressure is 100 kPa, calculate absolute pressure.
A 70 kPa
B 100 kPa
C 130 kPa
D 30 kPa
Answer: C. 130 kPa. Absolute pressure equals gauge pressure plus atmospheric pressure.
What does a dry basis for gas composition exclude from the total moles used?
A Water vapour
B Carbon dioxide
C Oxygen
D Nitrogen
Answer: A. Water vapour. Dry gas composition removes water vapour from the normalising total.
For elemental balances on a chemical reactor, which quantity is conserved by ordinary chemical reaction?
A Total number of molecules always
B Atoms of each element
C Moles of each molecule
D Volume of reacting gas
Answer: B. Atoms of each element. Reactions change molecular species but conserve the number of atoms of every element.
Which energy term changes when a process stream’s velocity changes?
A Reference pressure
B Chemical formula
C Mole fraction automatically
D Kinetic energy
Answer: D. Kinetic energy. Specific kinetic energy is one half of velocity squared.
From 50 mol of A fed, 30 mol reacts. What is A’s conversion?
A 150%
B 60%
C 40%
D 30%
Answer: B. 60%. Divide 30 mol reacted by 50 mol fed.
Which calculation step changes a flow rate from kg/h to kg/s?
A Multiply by 1,000
B Divide by 60 only
C Multiply by 3,600
D Divide by 3,600
Answer: D. Divide by 3,600. One hour consists of 3,600 seconds, so a per-hour rate is divided by 3,600.
Compared with the stoichiometric amount required, what is true of an excess reactant feed?
A It is supplied above requirement
B It is supplied below requirement
C It is absent from products
D It is always inert
Answer: A. It is supplied above requirement. An excess reactant is fed in more than the amount needed for the limiting reactant to react completely.
Which temperature scale belongs in the ideal gas equation when R uses SI kelvins?
A Kelvin
B Celsius
C Degrees of angle
D Fahrenheit
Answer: A. Kelvin. An absolute temperature scale is required. With the stated gas constant, enter temperature in kelvins.
How is raising a material stream’s elevation reflected in an energy balance?
A Decreased species molar mass
B Increased mole fraction always
C Increased gravitational potential energy
D New latent heat of reaction
Answer: C. Increased gravitational potential energy. Specific gravitational potential energy is proportional to elevation at fixed gravitational acceleration.
Energy to vaporise liquid at its boiling point at fixed pressure is what type of heat?
A Shaft work
B Latent heat
C Kinetic energy
D Sensible heat only
Answer: B. Latent heat. Latent heat accounts for a phase transition without a temperature change at saturation.
On a flowsheet, what information should label a known stream before a material balance is written?
A Only pump power
B Only pipe length
C Rate and composition
D Heat capacity only
Answer: C. Rate and composition. Rate and composition indicate the amount of material and each species crossing the balance boundary.
Why do tabulated enthalpies specify a reference state?
A Eliminate all heat capacity
B Define the energy datum
C Alter the measured mass
D Fix all velocities at zero
Answer: B. Define the energy datum. Enthalpy differences depend on using a consistent datum for the quantities being subtracted.
Dalton’s law adds which quantities to find the pressure of an ideal gas mixture?
A Individual liquid viscosities
B Heat capacities only
C Component partial pressures
D Component molar masses only
Answer: C. Component partial pressures. For an ideal gas mixture the total pressure is the sum of the component partial pressures.