A 1:2000 map shows 3.5 cm. Find ground distance.
A 70 m
B 7 m
C 35 m
D 700 m
Answer: A. 70 m. Three and a half centimetres times 2000 equals 7000 cm, or 70 m.
A 1:5000 map shows 4.2 cm. Find ground distance.
A 21 m
B 210 m
C 84 m
D 2100 m
Answer: B. 210 m. Four point two centimetres times 5000 equals 21,000 cm, or 210 m.
At scale 1:1000, what ground area does 1 cm² represent?
A 10 m²
B 100 m²
C 1000 m²
D 10,000 m²
Answer: B. 100 m². One centimetre represents 10 m, so one square centimetre represents 10 times 10, or 100 square metres.
BM RL is 100.000 m and BS is 1.250 m. If FS is 1.725 m, find point RL.
A 98.275 m
B 100.475 m
C 99.525 m
D 101.725 m
Answer: C. 99.525 m. Height of instrument is 100.000 plus 1.250, or 101.250 m; subtracting the foresight 1.725 gives 99.525 m.
In rise-and-fall levelling, the next staff reading drops from 1.250 m to 1.000 m. Find rise.
A 0.125 m
B 1.000 m
C 0.250 m
D 2.250 m
Answer: C. 0.250 m. A smaller staff reading from the same instrument height indicates a rise of 1.250 minus 1.000, or 0.250 m.
What is the theoretical interior-angle sum of a pentagonal traverse?
A 360 degrees
B 540 degrees
C 450 degrees
D 720 degrees
Answer: B. 540 degrees. For a plane polygon the interior-angle sum is (n minus 2) times 180 degrees; for n=5 it is 540 degrees.
A 100 m line has azimuth 30°. Find east departure.
A 50 m
B 43.3 m
C 86.6 m
D 100 m
Answer: A. 50 m. With azimuth clockwise from north, east departure is L sin azimuth: 100 times 0.5 is 50 m.
A traverse has east misclosure 0.3 m and north misclosure -0.4 m. Find linear closure error.
A 0.1 m
B 0.35 m
C 0.7 m
D 0.5 m
Answer: D. 0.5 m. Closure magnitude is the square root of 0.3 squared plus 0.4 squared, which is 0.5 m.
Contours have 5 m interval and are 100 m apart horizontally. Find slope percent.
A 5 percent
B 2 percent
C 10 percent
D 20 percent
Answer: A. 5 percent. Slope percent is rise over run times 100: 5 divided by 100 times 100 equals 5 percent.
A stadia instrument has K 100 and staff intercept 1.2 m. Find approximate distance, C=0.
A 12 m
B 100 m
C 121.2 m
D 120 m
Answer: D. 120 m. The stadia distance is K times staff intercept plus C: 100 times 1.2 plus zero equals 120 m.
A 50 m slope distance has 30 m vertical difference. Find horizontal distance.
A 20 m
B 30 m
C 40 m
D 60 m
Answer: C. 40 m. The right triangle relation gives horizontal distance as the square root of 50 squared minus 30 squared, or 40 m.
A 30 m tape is actually 30.02 m. Correction for a measured 100 m is approximately?
A +0.067 m
B -0.067 m
C +0.020 m
D -0.020 m
Answer: A. +0.067 m. The tape is long, so the true distance is larger: 100 times 0.02 divided by 30 is about +0.067 m.
A 100 m steel tape warms 20°C; α is 11.6×10⁻⁶/°C. Find length correction.
A +0.0232 m
B -0.0232 m
C +0.00232 m
D +0.232 m
Answer: A. +0.0232 m. Temperature correction is α L ΔT: 11.6×10⁻⁶ times 100 times 20 equals +0.0232 m.
A closed levelling run ends 0.04 m above its known closing elevation. What is misclosure magnitude?
A 0.02 m
B 0.08 m
C 4 m
D 0.04 m
Answer: D. 0.04 m. The elevation difference between the computed close and known close is the levelling misclosure, here 0.04 m.
A 100 m line at azimuth 30° has northing change approximately what?
A 50 m
B 86.6 m
C 70.7 m
D 100 m
Answer: B. 86.6 m. Northing change is L cos azimuth: 100 times cos 30 degrees is about 86.6 m.
A right angle is measured as 90° 00′ 20″. What is angular error?
A -20 seconds
B +20 minutes
C Zero
D +20 seconds
Answer: D. +20 seconds. The measured angle exceeds the right angle by 20 seconds, so its angular error is +20 seconds.
What is the minimum satellite count for a standalone 3D GNSS fix with receiver clock bias?
A Two satellites
B Four satellites
C Three satellites
D Six satellites
Answer: B. Four satellites. A three-dimensional position plus receiver clock bias has four unknowns, so at least four satellites are needed.
A fore bearing is 75°. Find ideal back bearing.
A 105 degrees
B 165 degrees
C 285 degrees
D 255 degrees
Answer: D. 255 degrees. For whole-circle bearings without local attraction, add 180 degrees when the fore bearing is below 180 degrees.
A 100 m horizontal distance has vertical angle 30°. Find height difference.
A 57.7 m
B 50 m
C 86.6 m
D 100 m
Answer: A. 57.7 m. Height difference is horizontal distance times tan angle: 100 times tan 30 degrees is about 57.7 m.
What is the primary purpose of a backsight on a known RL in HI levelling?
A Set contour spacing
B Find tape temperature
C Measure magnetic dip
D Establish height of instrument
Answer: D. Establish height of instrument. The backsight is added to the known reduced level to obtain the height of instrument.
An angular sum for a pentagon is measured as 542°. Find total angular misclosure.
A -2 degrees
B +18 degrees
C +2 degrees
D Zero
Answer: C. +2 degrees. The theoretical sum is 540 degrees, so the observed sum has a positive 2 degree misclosure.
At a contour crossing, what direction is steepest descent?
A Along the contour
B Perpendicular to contours
C At 45 degrees always
D Toward higher elevations
Answer: B. Perpendicular to contours. The steepest slope direction is perpendicular to contour lines, from higher to lower elevation.
What is the main use of a change point?
A Measure magnetic declination
B Set a map scale
C Carry level datum forward
D Find tape sag
Answer: C. Carry level datum forward. A change point transfers the elevation reference when the level instrument must be moved.
What is a temporary adjustment of a level intended to do?
A Set up and level instrument
B Change staff graduations
C Correct Earth curvature
D Set map projection
Answer: A. Set up and level instrument. Temporary adjustments prepare the instrument at a station, including setting up, levelling and focusing.
What does error of closure help evaluate?
A Map color quality
B Building occupancy
C Survey consistency
D Concrete mix strength
Answer: C. Survey consistency. Closure error provides a check on internal consistency and measurement quality for a closed survey.