A 1:1000 map shows 2 cm between points. Find ground distance.
A 2 m
B 10 m
C 200 m
D 20 m
Answer: D. 20 m. Two centimetres times 1000 equals 2000 cm, or 20 m.
In height-of-instrument levelling, how is RL found from HI and staff reading?
A HI plus staff reading
B Staff reading minus HI
C HI minus staff reading
D HI times staff reading
Answer: C. HI minus staff reading. The reduced level of a point equals the height of instrument minus the staff reading.
What is a change point used for in levelling?
A Measure contour interval
B Transfer elevation between setups
C Set magnetic declination
D Correct tape sag
Answer: B. Transfer elevation between setups. A change point receives a foresight before moving the instrument and a backsight after the next setup.
What is a foresight in levelling?
A First reading on benchmark
B Compass bearing
C Last reading before moving
D Tape temperature
Answer: C. Last reading before moving. A foresight is generally the final staff reading from one instrument setup, often on a change point or destination point.
What is an intermediate sight?
A Only a benchmark reading
B Reading between backsight and foresight
C A traverse bearing
D A tape correction
Answer: B. Reading between backsight and foresight. An intermediate sight is any staff reading from the setup that is neither the backsight nor foresight.
For a level loop, what should be checked at closure?
A Lamp voltage
B Elevation misclosure
C Concrete slump
D Traffic volume
Answer: B. Elevation misclosure. A closed levelling loop should return to a known elevation so the closing error can be computed.
What is reciprocal levelling useful for across?
A A short indoor corridor
B A flat tabletop
C A concrete cube
D Obstacle such as a river
Answer: D. Obstacle such as a river. Reciprocal observations from both sides help reduce collimation, curvature and refraction effects across an obstacle.
How do fore and back bearings differ ideally in whole-circle bearing?
A By 90 degrees
B By 270 degrees
C By 180 degrees
D They are equal
Answer: C. By 180 degrees. The back bearing of a line differs from its fore bearing by 180 degrees when local attraction is absent.
What can local attraction affect in compass surveying?
A Staff height
B Tape length only
C Magnetic bearing readings
D Contour interval
Answer: C. Magnetic bearing readings. Nearby magnetic materials can deflect the compass needle and introduce local attraction errors.
What is a backsight to a known point used for with a total station?
A Measure staff temperature
B Orient the instrument
C Set a contour line
D Correct soil bearing
Answer: B. Orient the instrument. A backsight to a known reference direction establishes instrument orientation for subsequent observations.
Using azimuth clockwise from north, what is east coordinate change?
A Length times sine azimuth
B Length times cosine azimuth
C Length divided by sine
D Azimuth times area
Answer: A. Length times sine azimuth. For a line length L and azimuth measured clockwise from north, the east departure is L sin azimuth.
Using azimuth clockwise from north, what is north coordinate change?
A Length times cosine azimuth
B Length times sine azimuth
C Length times tangent
D Azimuth divided by length
Answer: A. Length times cosine azimuth. The northing change is L cos azimuth when azimuth is measured clockwise from north.
What does traverse closure error indicate?
A Contour interval
B Mismatch in computed return position
C Staff zero
D Map projection name
Answer: B. Mismatch in computed return position. A closed traverse should return to its starting coordinates; the difference indicates accumulated measurement error.
What does a contour line crossing a stream valley often form?
A V pointing upstream
B V pointing downstream
C Circle around source
D Straight line only
Answer: A. V pointing upstream. Contours crossing a valley generally form a V that points toward higher ground and upstream.
What do GNSS satellites transmit to receivers?
A Timed ranging signals
B Contour elevations
C Tape corrections
D Magnetic declinations
Answer: A. Timed ranging signals. Receivers use the travel times of satellite signals, along with satellite orbit and clock data, to estimate position.
What does a low GNSS DOP generally indicate?
A Favorable satellite geometry
B Poor signal timing
C High tape error
D Large contour interval
Answer: A. Favorable satellite geometry. A lower dilution of precision generally indicates satellite geometry that supports a more stable position solution.
What does orienting a plane table accomplish?
A Measure benchmark elevation
B Align map with ground directions
C Correct chain length
D Compute staff readings
Answer: B. Align map with ground directions. Orientation aligns the plotted sheet with corresponding directions on the ground.
What do closed contour loops with rising values inward indicate?
A A valley
B A cliff only
C A level plain
D A hill
Answer: D. A hill. Closed contours with elevations increasing toward the center depict a hill or summit.
How is slope commonly expressed from rise and run?
A Run divided by area
B Rise times distance
C Elevation divided by bearing
D Rise divided by run
Answer: D. Rise divided by run. Slope gradient is vertical change divided by horizontal distance, often expressed as a ratio or percentage.
What tape correction applies when a tape is warmer than standard?
A Curvature correction
B Refraction correction
C Collimation correction
D Temperature correction
Answer: D. Temperature correction. Tape length changes with temperature, so measurements may need correction relative to the standard temperature.
What does sag correction account for in suspended tape measurement?
A Tape curve under its weight
B Magnetic declination
C Instrument collimation
D Map projection
Answer: A. Tape curve under its weight. A suspended tape sags under its own weight, making its curved length longer than the horizontal chord.
What does slope-distance reduction produce?
A Magnetic bearing
B Vertical datum
C Horizontal distance
D Contour interval
Answer: C. Horizontal distance. A measured slope distance is reduced to its horizontal component for plan position computations.
What does a field book preserve?
A Only final map colors
B Only equipment serial numbers
C Survey observations and notes
D Only project budget
Answer: C. Survey observations and notes. A field book records observations, station identifiers, sketches and notes needed for checking and computation.
What is a ranging rod used to mark?
A Survey station or line point
B Benchmark elevation
C Instrument temperature
D Contour interval
Answer: A. Survey station or line point. A ranging rod marks a station or helps align points along a survey line.
What is a horizontal control point?
A Point with known soil strength
B A contour label
C A tape correction
D Point with known plan coordinates
Answer: D. Point with known plan coordinates. Horizontal control points provide known plan coordinates for locating detailed survey features.