Difficulty: Easy & Basic
What does a VOR TO/FROM flag indicate?
A Aircraft altitude
B Course direction
C Radio strength
D Wind direction
Answer: B. Course direction. The flag indicates whether the selected course leads to or from the VOR station.
An ADF bearing needle points toward which facility?
A VOR station
B ILS runway
C DME antenna
D NDB station
Answer: D. NDB station. An automatic direction finder senses a non-directional beacon and indicates its relative bearing.
An altitude encoder supplies which value to a reporting transponder?
A Pressure altitude
B Radio height
C True altitude
D Cabin altitude
Answer: A. Pressure altitude. Altitude-reporting equipment sends encoded pressure altitude to the transponder.
Which unit lets the crew select radios and adjust received audio?
A DME unit
B AHRS
C Audio panel
D Flight director
Answer: C. Audio panel. The audio panel routes selected receivers and transmitters to headsets and microphones.
What angle does an angle-of-attack system indicate?
A Pitch to horizon
B Airflow to reference
C Bank to vertical
D Yaw to runway
Answer: B. Airflow to reference. Angle of attack relates the local airflow direction to the aircraft wing reference line.
Why is pitot heat installed?
A Prevent ice blockage
B Measure fuel flow
C Warm cabin air
D Improve radio range
Answer: A. Prevent ice blockage. Heating helps prevent ice from blocking the pitot opening and disrupting pressure sensing.
A radio altimeter primarily measures height above what?
A Mean sea level
B Cloud base
C Pressure datum
D Terrain below
Answer: D. Terrain below. A radio altimeter measures aircraft height above the surface using reflected radio signals.
What does an ILS marker beacon help identify?
A Runway heading
B Approach position
C Wind speed
D Aircraft range
Answer: B. Approach position. Marker beacons provide passage indications at specified points along some instrument approaches.
Which display normally presents primary flight parameters?
A MFD
B Audio panel
C PFD
D Control head
Answer: C. PFD. The primary flight display groups key flight information such as attitude, airspeed, and altitude.
Which display often presents moving maps and system pages?
A MFD
B PFD
C CDI
D Standby compass
Answer: A. MFD. A multifunction display can show maps, weather, and aircraft system pages.
What do flight director command bars provide?
A Direct servo motion
B Engine power
C Pitch and roll guidance
D Radio bearing
Answer: C. Pitch and roll guidance. Flight director cues show the pitch and roll needed to follow selected guidance.
What do avionics aural alerts provide?
A Hydraulic pressure
B Visual maps
C Radio distance
D Sound warnings
Answer: D. Sound warnings. Aural alerts use tones or spoken messages to draw attention to system conditions.
A TCAS resolution advisory calls for what?
A Radio retuning
B Vertical maneuver
C Runway change
D Fuel balancing
Answer: B. Vertical maneuver. A resolution advisory gives vertical guidance intended to resolve a traffic conflict.
Why are duplicate avionics channels installed?
A Reduce wing loading
B Improve fault tolerance
C Increase lift
D Change center of gravity
Answer: B. Improve fault tolerance. Redundant channels can preserve important functions after a component failure.
What is a digital avionics data bus used for?
A Sharing system data
B Routing fuel
C Cooling displays
D Driving brakes
Answer: A. Sharing system data. Digital data buses carry information between avionics units and displays.
Shielding an avionics cable mainly reduces what?
A Hydraulic leakage
B Pressure loss
C Electromagnetic interference
D Structural vibration
Answer: C. Electromagnetic interference. Cable shielding limits unwanted electromagnetic coupling into or out of signal wiring.
Why do radios provide active and standby frequencies?
A Raise transmit power
B Store altitude data
C Set audio volume
D Preselect next channel
Answer: D. Preselect next channel. A standby window lets a crew prepare another frequency before making it active.
What does an avionics circuit breaker protect against?
A Excess current
B Low airspeed
C Weak GPS
D High cabin pressure
Answer: A. Excess current. Circuit breakers open a circuit when current becomes excessive, protecting wiring and equipment.
Pressing a push-to-talk switch usually does what?
A Changes nav source
B Keys the transmitter
C Sets altitude
D Tests the ELT
Answer: B. Keys the transmitter. The push-to-talk control connects the microphone to the selected radio transmitter.
A remote flux sensor helps determine which quantity?
A Radio altitude
B Engine torque
C Magnetic heading
D Static pressure
Answer: C. Magnetic heading. A remote magnetic sensor measures the Earth’s field for heading reference.
TAWS combines aircraft position with what?
A Fuel database
B Airport audio
C Weather channel
D Terrain database
Answer: D. Terrain database. Terrain awareness systems compare aircraft position and flight path with terrain information.
Which radio can support long-range voice beyond VHF horizon?
A Marker receiver
B HF transceiver
C VOR receiver
D DME receiver
Answer: B. HF transceiver. High-frequency radio can support long-range communication through skywave propagation.
What does the transponder IDENT control do?
A Changes altitude source
B Selects a VOR
C Highlights radar return
D Resets the GPS
Answer: C. Highlights radar return. IDENT makes the aircraft’s transponder return stand out briefly on a controller’s display.
Which function does a cockpit intercom provide?
A Crew voice communication
B Terrain mapping
C Distance measurement
D Course guidance
Answer: A. Crew voice communication. An intercom allows crew members to communicate through their headsets.
Where are coded waypoints and procedures normally stored for an FMS?
A Audio memory
B Radar memory
C Cabin database
D Navigation database
Answer: D. Navigation database. The FMS uses a navigation database containing coded waypoints, routes, and procedures.