What does a battery’s cold-cranking rating describe?
A Stored fuel volume
B Starting current in cold conditions
C Alternator belt tension
D Starter gear size
Answer: B. Starting current in cold conditions. Cold-cranking amperes indicate a battery’s ability to deliver current for starting under specified cold test conditions.
Ampere-hour capacity mainly indicates what?
A Charge delivered over time
B Maximum alternator speed
C Fuse interrupt rating
D Spark-plug voltage
Answer: A. Charge delivered over time. An ampere-hour rating describes how much current a battery can supply over a specified discharge period.
A 12 V lead-acid battery has how many cells?
A Three
B Four
C Twelve
D Six
Answer: D. Six. A conventional 12 V lead-acid battery has six cells of about 2 V nominal each.
A fully charged lead-acid cell is about what at rest?
A 2.1 V
B 1.0 V
C 3.0 V
D 6.0 V
Answer: A. 2.1 V. A rested, fully charged lead-acid cell is typically near 2.1 V, depending on temperature and condition.
What can prolonged low charge cause inside a lead-acid battery?
A Sulfation
B Rotor runout
C Relay chatter
D Lamp flicker
Answer: A. Sulfation. Long periods at low charge can form lead-sulfate crystals that reduce battery capacity.
Corroded battery terminals can cause what?
A Higher alternator output
B High-resistance connection
C More starter torque
D Lower fuse rating
Answer: B. High-resistance connection. Corrosion can increase resistance and restrict current flow during starting or charging.
Why can a poor ground slow engine cranking?
A It changes spark timing
B It raises tire pressure
C It limits starter current
D It reduces oil viscosity
Answer: C. It limits starter current. The starter needs a low-resistance return path to draw its high operating current.
A rapid click with no crank may indicate what?
A Low battery voltage
B High coolant level
C Open headlamp lens
D Loose exhaust shield
Answer: A. Low battery voltage. Insufficient battery voltage or a poor high-current connection may make the starter solenoid chatter.
What can a loose alternator belt cause?
A Higher battery capacity
B Reduced charging output
C Lower starter current
D More spark-plug gap
Answer: B. Reduced charging output. A slipping belt can prevent the alternator from reaching the speed needed to supply rated output.
What can excessive AC ripple at the battery suggest?
A Worn wiper blade
B Weak horn relay
C Alternator diode fault
D Low tire pressure
Answer: C. Alternator diode fault. A failed rectifier diode can allow excessive alternating-current ripple into the DC system.
Why may the battery lamp glow with ignition on before starting?
A Battery is fully charged
B Starter is still engaged
C Brake fluid is low
D Alternator is not yet generating
Answer: D. Alternator is not yet generating. Before the engine turns the alternator, the charging circuit may illuminate its warning lamp as a normal check.
What can an unnoticed parasitic draw do?
A Increase alternator belt grip
B Discharge the parked battery
C Raise ignition voltage
D Improve cold cranking
Answer: B. Discharge the parked battery. A continuing current draw with the vehicle off can drain the battery over time.
What is a risk of reversing jump-start polarity?
A Higher tire friction
B Reduced spring travel
C Electrical component damage
D Improved charging
Answer: C. Electrical component damage. Reverse polarity can cause damaging current flow through vehicle electronics and protection devices.
Which fuse should replace a blown fuse?
A Any larger rating
B A metal strip
C A lower-voltage lamp
D Same specified rating
Answer: D. Same specified rating. Use the specified current rating and type so the circuit remains properly protected.
What does a continuity test check?
A Battery chemical state
B Alternator belt wear
C Unbroken electrical path
D Starter pinion travel
Answer: C. Unbroken electrical path. A continuity test checks whether an electrical path is complete, usually with power removed.
Why should resistance be measured on a de-energized circuit?
A Raise charging voltage
B Increase starter speed
C Avoid misleading readings
D Protect tire sensors
Answer: C. Avoid misleading readings. Live circuit voltage can make resistance measurements inaccurate and may damage a meter.
Which meter setting measures battery voltage?
A AC amps
B Ohms only
C Frequency
D DC volts
Answer: D. DC volts. A vehicle battery provides direct current, so use the meter’s DC-voltage range.
What does a relay’s coil energize?
A Switching contacts
B Brake pads
C Alternator belt
D Battery cells
Answer: A. Switching contacts. Current in the relay coil creates a magnetic field that moves the contacts.
A fuse element is broken. What has happened electrically?
A The circuit is grounded
B Voltage is doubled
C The circuit is open
D Resistance is zero
Answer: C. The circuit is open. A melted fuse breaks continuity and opens the protected circuit.
What can a short to ground cause?
A Zero battery mass
B Lower tire grip
C Longer wheelbase
D Excessive current
Answer: D. Excessive current. A low-resistance path to ground can draw excessive current and open the fuse.
Why do many vehicles use LED signal lamps?
A Higher fuel octane
B More brake pressure
C Lower electrical power use
D Longer wheelbase
Answer: C. Lower electrical power use. LEDs can provide the required light with less electrical power than comparable incandescent lamps.
What should be cleaned from battery terminals?
A Corrosion deposits
B Brake dust only
C Engine carbon
D Coolant scale
Answer: A. Corrosion deposits. Cleaning corrosion and securing terminals help restore reliable low-resistance connections.
Which issue can a voltage-drop test locate?
A Battery chemistry type
B Alternator rotor balance
C Spark-plug heat range
D Resistance in a loaded circuit
Answer: D. Resistance in a loaded circuit. A voltage-drop test reveals unwanted resistance while current is flowing through a circuit.
Why is wire insulation important?
A Increase current demand
B Prevent unintended contact
C Store electrical charge
D Reduce battery voltage
Answer: B. Prevent unintended contact. Insulation prevents conductors from touching each other or vehicle metal and causing faults.
What can a dim headlamp at idle with many loads suggest?
A Battery has extra capacity
B Charging output may be low
C Fuse rating is high
D Starter motor is engaged
Answer: B. Charging output may be low. Low alternator output or a weak battery can cause system voltage to sag under heavy load.