Aerospace Manufacturing MCQs (Set-4)

Difficulty: Hard

Independent tolerances are 0.2, 0.3 and 0.1 mm. What is their RSS stack?

A 0.30 mm
B 0.60 mm
C 0.90 mm
D 0.37 mm

A process has tolerance width 0.6 mm and σ=0.05 mm. What is Cp?

A 2.0
B 1.0
C 1.5
D 3.0

For limits 9.8–10.2 mm, mean 10.05 mm and σ=0.05 mm, what is Cpk?

A 0.5
B 1.0
C 1.5
D 2.0

For a 20 mm cutter at 120 m/min, what spindle speed is closest?

A 955 rpm
B 1,273 rpm
C 1,910 rpm
D 2,400 rpm

At 1,500 rpm and 0.12 mm/rev, what feed rate results?

A 90 mm/min
B 120 mm/min
C 240 mm/min
D 180 mm/min

A 500 mm aluminum part warms by 80°C. With α=23×10⁻⁶/°C, expansion is about what?

A 0.46 mm
B 0.92 mm
C 1.84 mm
D 9.20 mm

A 250 mm feature shrinks by 0.8% during processing. What is shrinkage?

A 2.0 mm
B 0.8 mm
C 1.5 mm
D 4.0 mm

Fiber mass is 0.72 kg at 1.8 g/cc; resin mass is 0.48 kg at 1.2 g/cc. Fiber volume fraction is what?

A 40%
B 60%
C 50%
D 75%

A ferromagnetic steel part has a surface crack. Which NDT method fits?

A Liquid penetrant only
B Magnetic particle
C Thermography only
D Hardness testing

A hidden composite delamination is suspected. Which inspection is appropriate?

A Magnetic particle
B Hardness testing
C Visual only
D Ultrasonic testing

Why can computed tomography help with complex AM passages?

A Measures paint color
B Sets cutting speed
C Shows internal geometry
D Removes residual stress

Active thermography identifies a defect through what effect?

A Changed heat flow
B Magnetic attraction
C Electrical resistance only
D Sound absorption

A powder-bed support is most important beneath what feature?

A Finished bore
B Unsupported overhang
C Flat base plate
D Machined datum

Why is build orientation selected before metal AM?

A Change alloy chemistry
B Set aircraft CG
C Eliminate inspection
D Control supports and distortion

Laser power 200 W, speed 800 mm/s, hatch 0.1 mm, layer 0.05 mm. Energy density is what?

A 50 J/mm³
B 25 J/mm³
C 100 J/mm³
D 200 J/mm³

Why monitor powder spreading during laser powder-bed fusion?

A Measure cabin altitude
B Set hole position
C Detect uneven layers
D Inspect fuel seals

How should material lot identity be preserved through aerospace production?

A Mix all batches
B Remove certificates
C Reuse unknown powder
D Maintain traceable records

What does a material certificate help verify?

A Aircraft route
B Specified material properties
C Toolpath color
D Operator speed

Why qualify each metal powder-bed machine and process?

A Establish controlled capability
B Increase wing loading
C Reduce part size
D Avoid all testing

A composite autoclave cycle misses its specified pressure. What is the correct response?

A Ignore the deviation
B Add extra resin later
C Assess against approved criteria
D Ship without review

A hole exits a composite laminate with breakout. Which process change may help?

A Increase drill runout
B Remove the backing
C Use blunt tooling
D Add exit-side backing

Why is a powder-bed build conducted in controlled atmosphere?

A Increase tool vibration
B Limit oxidation and contamination
C Reduce dimensional checks
D Change part density directly

A cure thermocouple reads outside the approved cycle. What does the record support?

A Disposition review
B Automatic acceptance
C Material substitution
D Tool redesign

Why must NDT accept/reject criteria match approved design data?

A Increase inspection speed only
B Avoid calibration
C Ensure consistent disposition
D Replace process control

A feature is within size tolerance but has a crack indication. What governs acceptance?

A Dimension alone
B Approved flaw criteria
C Surface color
D Machine cycle time