Difficulty: Medium
Why is liquid penetrant testing unsuitable on porous surfaces?
A It needs magnetism
B Sound cannot enter
C X-rays cannot pass
D Background penetrant remains
Answer: D. Background penetrant remains. Porosity retains penetrant and creates background that can mask relevant indications.
Magnetic-particle inspection is limited mainly to which materials?
A All plastics
B Aluminum alloys
C Ferromagnetic materials
D Glass composites
Answer: C. Ferromagnetic materials. Magnetic-particle testing requires a ferromagnetic material that can be magnetized.
Why is couplant applied during ultrasonic inspection?
A Remove air gaps
B Increase part hardness
C Block all echoes
D Cool the material
Answer: A. Remove air gaps. Couplant improves acoustic transmission by displacing air between the probe and test surface.
An internal void changes material density. Which inspection can reveal it?
A Liquid penetrant
B Radiography
C Visual check
D Hardness test
Answer: B. Radiography. Radiography records differences in attenuation caused by internal density changes.
Which material property is needed for eddy-current testing?
A Magnetic polarity only
B Porosity
C Electrical conductivity
D Transparency
Answer: C. Electrical conductivity. Eddy currents are induced in electrically conductive materials.
Thermography can find composite defects by measuring what?
A Magnetic field strength
B Hardness variation
C Fuel vapor
D Surface temperature patterns
Answer: D. Surface temperature patterns. Thermal imaging can reveal subsurface anomalies that change heat flow at the surface.
A composite cure specification normally controls which cycle variables?
A Fuel and oxygen
B Time and temperature
C RPM and feed
D Voltage and frequency
Answer: B. Time and temperature. Cure specifications define time and temperature, and may also specify pressure and vacuum.
A leaking vacuum bag during layup most directly risks what?
A Voids in laminate
B Higher fiber count
C Lower tool wear
D More rivet strength
Answer: A. Voids in laminate. Insufficient vacuum compaction can trap air or volatiles and create laminate porosity.
Which method can produce three-dimensional internal images?
A Dye penetrant
B Magnetic particle
C Computed tomography
D Visual inspection
Answer: C. Computed tomography. Computed tomography reconstructs a three-dimensional image from multiple radiographic projections.
What does a datum establish on an engineering drawing?
A Alloy chemistry
B Measurement reference
C Cure temperature
D Tool speed
Answer: B. Measurement reference. A datum is a theoretical reference used to locate and measure features.
For a worst-case tolerance stack, how are individual tolerances combined?
A Average them
B Multiply dimensions
C Ignore the smallest
D Add absolute values
Answer: D. Add absolute values. Worst-case analysis sums the maximum possible dimensional deviations.
What does first-article inspection verify?
A Tool color
B Operator shift length
C Initial part conformity
D Powder supplier price
Answer: C. Initial part conformity. First-article inspection checks that the initial production part meets drawing and process requirements.
A control chart point crosses a control limit. What may it signal?
A Special process cause
B Normal variation only
C Perfect capability
D Material traceability
Answer: A. Special process cause. A point beyond a control limit suggests an assignable or special cause requiring investigation.
At 1,200 rpm and 0.15 mm/rev, what CNC feed rate results?
A 90 mm/min
B 180 mm/min
C 120 mm/min
D 240 mm/min
Answer: B. 180 mm/min. Feed rate equals feed per revolution times spindle speed: 0.15 Γ 1,200 = 180 mm/min.
Worn cutting tools most directly threaten which result?
A Fuel pressure
B Fiber orientation
C Part traceability
D Dimensional accuracy
Answer: D. Dimensional accuracy. Tool wear changes cutting geometry and can move machined dimensions out of tolerance.
Why is a backup plate useful when drilling a laminate?
A Heat the drill
B Increase fiber angle
C Support exit plies
D Measure hole depth
Answer: C. Support exit plies. Backing supports the exit surface and helps limit breakout and delamination.
What must a prepreg out-time log record?
A Exposure duration
B Cutting speed
C X-ray dose
D Rivet diameter
Answer: A. Exposure duration. The log records accumulated exposure outside controlled cold storage.
Why use a balanced laminate layup?
A Increase porosity
B Limit coupling and warping
C Remove all resin
D Avoid fiber direction
Answer: B. Limit coupling and warping. Balanced stacking helps reduce in-plane coupling and distortion under load or cure.
A nonconformance report documents what?
A Tool calibration date only
B Operator attendance
C Part shipping cost
D Deviation from requirements
Answer: D. Deviation from requirements. A nonconformance record identifies a product or process condition that does not meet requirements.
What does process qualification establish?
A One successful prototype
B A lower purchase price
C Repeatable capable process
D A new aircraft route
Answer: C. Repeatable capable process. Qualification shows a defined process can repeatedly produce acceptable output under controlled conditions.
In-situ additive monitoring can detect what during a build?
A Aircraft yaw
B Layer anomalies
C Cabin pressure
D Fastener torque
Answer: B. Layer anomalies. In-process sensors can identify irregularities such as layer lift or incomplete fusion.
Why is inert shielding gas used in metal powder-bed fusion?
A Limit oxidation
B Increase gravity
C Cool the cabin
D Measure porosity
Answer: A. Limit oxidation. A controlled inert atmosphere limits oxidation during laser processing of reactive metal powder.
Reducing additive layer thickness generally does what?
A Increase layer height
B Remove supports
C Improve layer resolution
D Eliminate postprocessing
Answer: C. Improve layer resolution. Thinner layers can improve vertical resolution and surface quality, usually with more build time.
Uneven thermal contraction during build can cause what defect?
A Improved tolerance
B Higher conductivity
C Less residual stress
D Part distortion
Answer: D. Part distortion. Uneven heating and cooling can create residual stress and distort the component.
Why are critical additive surfaces often machined after printing?
A Meet final tolerances
B Change alloy identity
C Set fiber direction
D Remove all internal pores
Answer: A. Meet final tolerances. Postprocessing machining brings critical interfaces and dimensions to final specification.