Difficulty: Hard
If 1-g stall speed is 45 kt and load factor is 4, accelerated stall speed is?
A 45 kt
B 90 kt
C 64 kt
D 180 kt
Answer: B. 90 kt. Stall speed scales with the square root of load factor: 45√4 = 90 kt.
A clean aircraft stalls at 100 kt with CLmax=1.5. If flaps raise CLmax to 2.0, new stall speed is about?
A 86.6 kt
B 75.0 kt
C 100 kt
D 115.5 kt
Answer: A. 86.6 kt. Vsf = Vs√(CLmax clean/CLmax flaps) = 100√(1.5/2.0) ≈ 86.6 kt.
In a coordinated level turn banked 45°, load factor is approximately?
A 1.00
B 1.15
C 2.00
D 1.41
Answer: D. 1.41. For a level coordinated turn, n = 1/cosφ; at 45°, n ≈ 1.414.
At M∞=1.2 with 30° sweep, the normal Mach component is about?
A 0.60
B 0.85
C 1.20
D 1.04
Answer: D. 1.04. Mnormal = M∞cosΛ = 1.2cos30° ≈ 1.04.
Using CL≈2πα for a thin airfoil at small α, estimate CL at 5°.
A 0.09
B 0.55
C 0.35
D 1.10
Answer: B. 0.55. Convert 5° to 0.087 rad; 2π × 0.087 ≈ 0.55 under thin-airfoil assumptions.
At Mach 3, the Mach angle is approximately?
A 9.6 degrees
B 30 degrees
C 45 degrees
D 19.5 degrees
Answer: D. 19.5 degrees. μ = arcsin(1/3) ≈ 19.5 degrees.
With p∞=101 kPa, q∞=5 kPa and Cp=-0.6, surface pressure is?
A 98.6 kPa
B 101 kPa
C 98 kPa
D 104 kPa
Answer: C. 98 kPa. p = p∞ + Cpq∞ = 101 + (-0.6 × 5) = 98 kPa.
At fixed e and aspect ratio, doubling CL changes induced drag coefficient how?
A It doubles
B It quadruples
C It halves
D It stays fixed
Answer: B. It quadruples. CDi is proportional to CL², so doubling CL multiplies CDi by four.
If q doubles while CD and reference area stay fixed, drag does what?
A It halves
B It quadruples
C It stays fixed
D It doubles
Answer: D. It doubles. The drag equation is linear in dynamic pressure when CD and area remain unchanged.
In supersonic flow, a turn over a convex surface creates what?
A Normal shock
B Expansion fan
C Detached bow shock
D Stagnation bubble
Answer: B. Expansion fan. A convex expansion turn generates a centered Prandtl–Meyer expansion fan.
When supersonic flow turns toward itself at a compression corner, what forms?
A Expansion fan
B Oblique shock
C Mach cone only
D Laminar bubble
Answer: B. Oblique shock. Compression turning in supersonic flow produces an oblique shock.
Through an ideal Prandtl–Meyer expansion, local Mach number generally does what?
A Decreases
B Becomes zero
C Stays sonic
D Increases
Answer: D. Increases. Supersonic expansion accelerates the flow and raises its Mach number.
Across a shock wave, static pressure generally does what?
A Increases
B Decreases
C Stays unchanged
D Becomes zero
Answer: A. Increases. Compression across a shock raises static pressure.
Across a shock wave, stagnation pressure generally does what?
A Decreases
B Increases
C Stays constant
D Equals static pressure
Answer: A. Decreases. Shock processes are irreversible and reduce total pressure.
Behind an attached oblique shock at moderate turning, flow is usually what?
A Always subsonic
B Exactly sonic
C Still supersonic
D At rest
Answer: C. Still supersonic. For an attached oblique shock, downstream flow is normally supersonic.
If a supersonic corner turns the flow too sharply, the oblique shock will do what?
A Vanish
B Become an expansion fan
C Turn laminar
D Detach
Answer: D. Detach. Above the maximum attached turning angle, the shock detaches upstream.
Drag-divergence Mach number marks what?
A Zero lift
B Minimum Reynolds number
C Rapid drag rise
D First boundary layer
Answer: C. Rapid drag rise. It marks the onset of a sharp compressibility-related increase in drag.
Compressibility and shock effects contribute to which drag component?
A Wave drag
B Skin-friction drag
C Induced drag
D Rolling drag
Answer: A. Wave drag. Wave drag is associated with compressibility and shock-wave formation.
The area rule smooths which distribution along the aircraft axis?
A Lift coefficient
B Cross-sectional area
C Wing incidence
D Boundary-layer thickness
Answer: B. Cross-sectional area. The rule controls total cross-sectional area variation to reduce transonic drag rise.
A strong shock interacting with a low-energy boundary layer may cause what?
A Laminarization
B Lift symmetry
C Flow separation
D Zero drag
Answer: C. Flow separation. The abrupt pressure rise can separate the boundary layer and increase drag.
For an ideal symmetric airfoil at zero angle of attack, lift is approximately what?
A Maximum
B Negative maximum
C Zero
D Equal to drag
Answer: C. Zero. Symmetry gives zero lift at zero incidence in ideal attached flow.
At M∞=0.82 with local flow exceeding Mach 1, which feature commonly terminates it?
A Shock wave
B Winglet
C Expansion fan
D Leading edge
Answer: A. Shock wave. A local supersonic pocket on a transonic wing commonly ends at a shock.
Area-rule cross sections are taken in planes normal to what?
A Freestream direction
B Wing chord
C Vertical axis
D Fuselage floor
Answer: A. Freestream direction. The relevant area distribution uses sections perpendicular to the flight direction.
A normal shock is oriented how relative to incoming flow?
A Parallel to flow
B At 45 degrees
C Perpendicular to flow
D Along the wing span
Answer: C. Perpendicular to flow. A normal shock stands normal to the upstream flow direction.
A Prandtl–Meyer expansion is ideally what type of process?
A Isentropic
B Irreversible
C Isothermal only
D Constant-pressure
Answer: A. Isentropic. The ideal expansion fan is isentropic, unlike the irreversible shock process.