Difficulty: Easy & Basic
During a wing stall, what happens to airflow over much of the surface?
A Flow becomes inviscid
B Mach number becomes zero
C Flow separates
D Wingtip vortices vanish
Answer: C. Flow separates. A stall involves substantial boundary-layer separation after critical angle of attack.
Which limit marks the onset of an aerodynamic stall?
A Critical Reynolds number
B Critical angle of attack
C Maximum Mach number
D Zero-lift speed
Answer: B. Critical angle of attack. A wing stalls when its critical angle of attack is exceeded.
Leading-edge slats mainly help by doing what?
A Reducing wing area
B Delaying separation
C Increasing wave drag
D Removing camber
Answer: B. Delaying separation. Slats help the airflow remain attached at higher angles of attack.
Deploying trailing-edge flaps usually changes lift and drag how?
A Both decrease
B Lift rises; drag falls
C Lift falls; drag stays
D Both increase
Answer: D. Both increase. Flaps increase maximum lift and usually add drag.
Why can extended flaps permit a slower approach?
A Lower aircraft weight
B Higher maximum lift
C Lower air density
D Smaller wing area
Answer: B. Higher maximum lift. A higher maximum lift coefficient supports flight at lower speed.
A plain flap changes which airfoil property most directly?
A Camber
B Aspect ratio
C Sweep angle
D Tip chord
Answer: A. Camber. Flap deflection increases the airfoil’s effective camber.
What does the lift-to-drag ratio indicate?
A Aerodynamic efficiency
B Structural stiffness
C Engine efficiency
D Static stability
Answer: A. Aerodynamic efficiency. L/D compares useful lift with aerodynamic resistance.
At maximum L/D in steady flight, total drag is what?
A At its maximum
B Exactly zero
C At its minimum
D Equal to lift
Answer: C. At its minimum. For a given aircraft, maximum L/D corresponds to minimum total drag.
With configuration held fixed, parasite drag generally does what as speed rises?
A Decreases
B Stays constant
C Becomes induced drag
D Increases
Answer: D. Increases. Parasite drag grows with dynamic pressure as speed increases.
In level flight at fixed weight, induced drag usually does what as speed rises?
A Increases
B Stays fixed
C Becomes wave drag
D Decreases
Answer: D. Decreases. Higher speed needs a lower lift coefficient for the same lift, reducing induced drag.
Across a broad speed range, total drag versus speed is typically what shape?
A Straight line
B U-shaped curve
C Flat plateau
D Inverted parabola
Answer: B. U-shaped curve. Induced drag dominates at low speed and parasite drag at high speed.
Very low flight over a runway produces which aerodynamic effect?
A Area rule
B Mach tuck
C Ground effect
D Venturi effect
Answer: C. Ground effect. Nearby ground changes the wing’s three-dimensional airflow pattern.
Ground effect alters which wing-flow features most directly?
A Downwash and vortices
B Camber and chord
C Mach angle and shock
D Reynolds number and density
Answer: A. Downwash and vortices. Ground proximity restricts vertical flow and changes downwash and wingtip vortices.
What happens to stall speed as load factor rises?
A It increases
B It decreases
C It stays constant
D It reaches zero
Answer: A. It increases. More load requires more lift, so a higher speed is needed at the same maximum lift coefficient.
A steeper coordinated level turn produces a higher what?
A Aspect ratio
B Taper ratio
C Mach angle
D Load factor
Answer: D. Load factor. A steeper level turn requires greater lift and therefore raises load factor.
Viscous shear along an aircraft surface produces which drag?
A Wave drag
B Induced drag
C Skin-friction drag
D Base pressure drag
Answer: C. Skin-friction drag. Skin-friction drag comes from viscous shear at the wetted surface.
Pressure differences associated with body shape contribute to which drag?
A Form drag
B Induced drag
C Wave drag
D Skin-friction drag
Answer: A. Form drag. Form drag is associated with pressure distribution and body shape.
An adverse pressure gradient can prompt what in a boundary layer?
A Flow acceleration
B Lower density only
C Spanwise lift
D Flow separation
Answer: D. Flow separation. Rising pressure downstream slows low-energy near-wall flow and can cause separation.
Taper ratio compares which chord lengths?
A Root chord to span
B Tip chord to root
C Span to area
D Mean chord to thickness
Answer: B. Tip chord to root. Taper ratio is tip chord divided by root chord.
With planform area fixed, increasing span makes aspect ratio what?
A Lower
B Higher
C Unchanged
D Negative
Answer: B. Higher. Aspect ratio is proportional to span squared at fixed wing area.
A small roughness strip near a wing nose can trigger boundary-layer what?
A Choking
B Expansion
C Cavitation
D Transition
Answer: D. Transition. A deliberate trip can move boundary-layer flow from laminar toward turbulent.
Wing washout gives its tip a what relative to the root?
A Lower incidence
B Higher camber
C Greater chord
D Higher sweep
Answer: A. Lower incidence. Washout twists the tip to a lower incidence angle than the root.
Raising a spoiler generally lowers lift and raises what?
A Drag
B Thrust
C Aspect ratio
D Lift coefficient
Answer: A. Drag. A raised spoiler disrupts upper-surface flow, reducing lift and increasing drag.
With a favorable pressure gradient, static pressure generally does what downstream?
A Rises downstream
B Stays fixed
C Falls downstream
D Becomes zero
Answer: C. Falls downstream. A favorable gradient has decreasing pressure in the flow direction.
If air density falls while lift is held constant, what must airspeed do?
A Decrease
B Stay unchanged
C Increase
D Reverse direction
Answer: C. Increase. Lower density requires higher dynamic pressure, supplied by greater speed if other terms stay fixed.