Why is a slow sand filter biologically active near its surface?
A Chlorine crystals form
B Sludge blanket rises
C Schmutzdecke develops
D Gravel dissolves
Answer: C. Schmutzdecke develops. A biologically active layer called schmutzdecke develops at the top of a slow sand filter.
Rapid sand filters are commonly cleaned by what method?
A Manual sewer rodding
B Anaerobic digestion
C Chemical softening
D Backwashing
Answer: D. Backwashing. Backwashing reverses flow to expand and clean the filter bed.
In coagulation, rapid mixing is used to do what?
A Settle sludge slowly
B Grow attached biofilm
C Disperse coagulant quickly
D Remove dissolved salts
Answer: C. Disperse coagulant quickly. Rapid mixing distributes coagulant throughout the water before flocculation.
Breakpoint chlorination is reached when demand is met and what appears?
A Free chlorine residual
B Higher turbidity
C More hardness
D Zero pH
Answer: A. Free chlorine residual. Beyond breakpoint, added chlorine produces a free residual after oxidizable demand is largely satisfied.
A contact tank provides what for disinfection?
A Space for grit settling
B Time for pathogen inactivation
C Sludge drying
D Water softening
Answer: B. Time for pathogen inactivation. Contact time allows the disinfectant to act before water enters distribution.
A clarifier surface overflow rate equals flow divided by what?
A Tank depth
B Plan area
C Sludge volume
D Pipe diameter
Answer: B. Plan area. Surface overflow rate is hydraulic flow divided by clarifier surface area.
Hydraulic detention time is volume divided by what?
A Water hardness
B Flow rate
C Pipe roughness
D Sludge age
Answer: B. Flow rate. HRT = tank volume divided by influent flow rate.
Higher organic loading in an aeration basin increases what demand?
A Water hardness
B Sludge drying
C Oxygen demand
D Screen opening size
Answer: C. Oxygen demand. More biodegradable substrate generally increases biological oxygen requirements.
MLSS is measured in which treatment unit?
A Raw-water intake
B Chlorine contact tank
C Grit chamber
D Aeration mixed liquor
Answer: D. Aeration mixed liquor. Mixed liquor suspended solids quantify biomass and other suspended matter in the aeration basin.
The food-to-microorganism ratio compares substrate with what?
A Biomass concentration
B Pipe length
C Chlorine residual
D Tank depth
Answer: A. Biomass concentration. F/M relates biodegradable organic load to the mass of microorganisms in the process.
Solids retention time tracks how long solids remain in what?
A Water distribution loop
B Raw-water reservoir
C Chlorine cylinder
D Biological process
Answer: D. Biological process. SRT or sludge age measures the average time biomass solids remain in the treatment system.
Return sludge flow helps maintain what in activated sludge?
A Biomass inventory
B Water hardness
C Chlorine contact time
D Grit removal
Answer: A. Biomass inventory. RAS returns settled microorganisms to maintain the desired biomass concentration.
Excess sludge is removed to control what?
A Water pH only
B Pipe pressure
C Screening rate
D Solids inventory
Answer: D. Solids inventory. Waste activated sludge controls the amount and age of biomass in the process.
Nitrification requires which general environment?
A Strictly anaerobic conditions
B Aerobic conditions
C Dry solids only
D No microorganisms
Answer: B. Aerobic conditions. Nitrification is an oxygen-dependent biological oxidation process.
Denitrification typically occurs under which condition?
A High dissolved oxygen
B Dry air exposure
C Anoxic conditions
D No nitrate present
Answer: C. Anoxic conditions. Denitrifying bacteria use nitrate under anoxic conditions rather than free dissolved oxygen.
A secondary treatment stage mainly removes what?
A Coarse floating debris
B All dissolved salts
C Biodegradable organics
D Water hardness
Answer: C. Biodegradable organics. Biological secondary treatment removes much of the biodegradable organic load.
A primary clarifier’s scum removal targets what?
A Floating oils and grease
B Dissolved nitrates
C Fine dissolved salts
D Disinfection residual
Answer: A. Floating oils and grease. Skimming removes floating scum, including fats, oils and grease.
A trickling-filter biofilm receives oxygen mainly from what?
A Air moving through media
B Anaerobic sludge gas
C Chlorine residual
D Water softener brine
Answer: A. Air moving through media. Air circulates through the voids in the media and supplies oxygen to the biofilm.
Anaerobic digestion commonly produces which useful gas mixture?
A Oxygen and chlorine
B Nitrogen and ozone
C Hydrogen peroxide only
D Methane and carbon dioxide
Answer: D. Methane and carbon dioxide. Digestion biogas is mainly methane and carbon dioxide, with minor constituents.
A sludge-digester gas holder is used to manage what?
A Filter backwash
B Biogas production
C Water hardness
D Sewer infiltration
Answer: B. Biogas production. Gas storage balances variable biogas production and use.
A pressure filter differs from an open rapid filter mainly by what?
A No filter media
B No solids removal
C Enclosed operation under pressure
D Anaerobic treatment
Answer: C. Enclosed operation under pressure. Pressure filters contain media in a closed vessel and operate under hydraulic pressure.
A water-distribution pressure zone helps manage what?
A Elevation-related pressures
B BOD removal
C Sludge age
D Sewer grade
Answer: A. Elevation-related pressures. Pressure zones control service pressure where elevations vary across the network.
A water hammer is a transient caused by what?
A Slow filtration
B Rapid flow change
C Coagulation
D Sludge settling
Answer: B. Rapid flow change. Sudden valve closure or pump changes can create pressure waves in pipes.
A water audit compares production with what?
A Sludge age only
B Filter media depth
C Rainfall intensity
D Authorized consumption and losses
Answer: D. Authorized consumption and losses. Water audits account for system input, authorized use and apparent or real losses.
A sanitary sewer’s self-cleansing objective is to limit what?
A Solids deposition
B Disinfection residual
C Water hardness
D Sludge digestion
Answer: A. Solids deposition. Adequate flow and slope help prevent solids from settling in sewers.