Wheelbase 2.8 m, track 1.4 m, inner angle 30°. What is ideal outer angle?
A About 18°
B About 30°
C About 24°
D About 36°
Answer: C. About 24°. For ideal Ackermann geometry, cot(outer) minus cot(inner) equals track divided by wheelbase; the outer angle is about 24°.
Wheelbase 2.5 m, track 1.5 m, inner angle 35°. Which outer angle is closest?
A About 20°
B About 26°
C About 35°
D About 42°
Answer: B. About 26°. The Ackermann relation gives cot(outer) = cot(35°) + 1.5/2.5, yielding approximately 26°.
What does pneumatic trail describe?
A Tire-force moment arm
B Steering-axis ground offset
C Rack travel per turn
D Tie-rod length change
Answer: A. Tire-force moment arm. Pneumatic trail is the effective distance between the tire contact-patch center and the resultant lateral-force action.
During split-friction braking, negative scrub radius can reduce what?
A Brake pedal travel
B Engine torque
C Wheelbase change
D Steering pull
Answer: D. Steering pull. Negative scrub radius can reduce steering disturbance when left and right front braking forces differ.
A 8 MPa pressure acts on 400 mm² piston area. What force results?
A 800 N
B 1,600 N
C 3,200 N
D 4,800 N
Answer: C. 3,200 N. Pressure equals 8 N/mm², so piston force is 8 × 400 = 3,200 N.
What does torsion-bar deflection indicate in hydraulic assist?
A Tire tread depth
B Road-wheel speed
C Brake temperature
D Driver steering torque
Answer: D. Driver steering torque. The torsion bar twists in proportion to steering input torque and operates the hydraulic control valve.
Which inputs commonly shape an EPS assist command?
A Coolant level and load
B Fuel pressure and rpm
C Steering torque and speed
D Brake wear and height
Answer: C. Steering torque and speed. EPS controllers use steering torque and vehicle speed among the inputs that determine assist.
In a permanent-magnet EPS motor, what mainly controls torque?
A Tire pressure
B Motor current
C Wheelbase
D Hydraulic flow
Answer: B. Motor current. For a given motor, torque is approximately proportional to current within its operating range.
What does EPS thermal derating usually reduce?
A Available assist torque
B Steering wheel diameter
C Caster angle
D Rack travel
Answer: A. Available assist torque. Thermal protection limits motor output to prevent excessive heating, so steering assistance can decrease.
Where does rack-assist EPS apply motor force?
A Directly to the rack
B At the brake pedal
C Inside the fuel rail
D At the rear axle
Answer: A. Directly to the rack. Rack-assist systems apply electric motor torque at the steering rack rather than only at the column.
At parking speeds, rear-wheel steering commonly uses which phase?
A Same-phase steering
B No front steering
C Counter-phase steering
D Fixed toe-in
Answer: C. Counter-phase steering. Opposite front and rear steering angles can reduce turning radius at low speed.
At high speed, same-phase rear steering mainly supports what?
A Shorter stopping distance
B Directional stability
C Higher engine output
D Lower tire pressure
Answer: B. Directional stability. Small same-direction rear steering can improve lane-change stability and reduce yaw response delay.
What does active front steering add to driver input?
A A controlled steering angle
B Extra brake pressure
C A longer wheelbase
D More tire camber
Answer: A. A controlled steering angle. Active front steering can superimpose a commanded angle on the driver’s steering input.
Why does steer-by-wire need fault-tolerant channels?
A Higher tire pressure
B No direct mechanical link
C Longer steering column
D Larger brake discs
Answer: B. No direct mechanical link. With no direct steering-wheel-to-rack connection, redundant sensing, control, power, or actuation helps manage faults safely.
A steer-by-wire controller detects a critical fault. What is a safety goal?
A Reach a safe vehicle state
B Increase steering ratio
C Disable every warning
D Lock the steering wheel
Answer: A. Reach a safe vehicle state. A safety design isolates faults and maintains controllability or transitions the vehicle toward a safe state.
What does a steer-by-wire handwheel actuator provide?
A Rack lubrication
B Brake assistance
C Tire alignment
D Driver steering feedback
Answer: D. Driver steering feedback. The handwheel actuator can generate feedback torque to communicate steering feel without a mechanical link.
Why can an engine-driven hydraulic pump consume power while cruising straight?
A It increases caster
B It turns the rear wheels
C It raises tire pressure
D It continues circulating fluid
Answer: D. It continues circulating fluid. A conventional belt-driven pump circulates fluid while the engine runs, creating parasitic losses even with little steering demand.
A control-arm bush deflects under cornering load. What may change?
A Brake fluid boiling point
B Wheel toe under load
C Steering ratio label
D Wheelbase measurement
Answer: B. Wheel toe under load. Suspension compliance can alter toe as tire forces deform bushings and joints.
What is roll steer?
A Toe change during braking
B Steering-wheel vibration
C Toe change during body roll
D Rack motion from torque
Answer: C. Toe change during body roll. Roll steer is a suspension-kinematic change in wheel steer angle associated with body roll.
A front steering ratio is 16:1. A 720° handwheel turn gives about what road-wheel angle?
A 45°
B 30°
C 60°
D 90°
Answer: A. 45°. The steering ratio is handwheel angle divided by road-wheel angle, so 720°/16 = 45°.
Why may ideal Ackermann geometry be imperfect at high lateral acceleration?
A Wheelbase becomes shorter
B Steering stops move
C Tires develop slip angles
D Brake pressure disappears
Answer: C. Tires develop slip angles. At higher lateral acceleration, tire slip angles influence the best wheel-angle relationship beyond pure rolling geometry.
Which design change can reduce bump-steer sensitivity?
A Increase brake-pad area
B Lower engine compression
C Widen the steering wheel
D Align linkage motion arcs
Answer: D. Align linkage motion arcs. Matching steering-link motion to suspension kinematics helps limit toe change through wheel travel.
How can stability control use steering angle?
A Measure brake-disc thickness
B Estimate driver path intent
C Measure engine oil pressure
D Measure tire tread
Answer: B. Measure commanded wheel direction. The controller compares requested path with measured vehicle motion to detect understeer or oversteer.
Why use independent power feeds in a safety-critical steer-by-wire design?
A Increase tire camber
B Shorten rack travel
C Raise hydraulic pressure
D Reduce single-point power failure
Answer: D. Reduce single-point power failure. Independent supplies can help prevent one electrical fault from removing all steering capability.
What can active rear steering regulate using yaw feedback?
A Vehicle directional response
B Engine fuel octane
C Brake lining thickness
D Steering wheel diameter
Answer: A. Vehicle directional response. Rear steering can be controlled from vehicle-motion feedback to shape yaw response and improve stability.