Difficulty: Easy & Basic
What is the steering system’s main function?
A Cool the engine
B Transmit fuel pressure
C Direct the road wheels
D Change the gear ratio
Answer: C. Direct the road wheels. The steering system converts driver input into direction changes at the road wheels.
Which part carries driver input from the wheel toward the gear?
A Tie rod end
B Radiator hose
C Fuel rail
D Steering column
Answer: D. Steering column. The steering column transmits input from the steering wheel to the steering gear.
How does a rack-and-pinion gear convert motion?
A Linear travel into heat
B Rotation into linear travel
C Fuel pressure into torque
D Wheel speed into voltage
Answer: B. Rotation into linear travel. The pinion rotates and moves the toothed rack laterally.
What does a tie rod connect in a steering linkage?
A Engine to gearbox
B Radiator to pump
C Rack to steering arm
D Wheel to brake disc
Answer: C. Rack to steering arm. Tie rods transfer rack movement to the steering arms or knuckles.
Which component supports the wheel hub and provides a steering pivot?
A Steering knuckle
B Oil sump
C Clutch disc
D Fuel injector
Answer: A. Steering knuckle. The steering knuckle carries the hub and pivots to turn the wheel.
In a recirculating-ball system, what does the Pitman arm do?
A Pumps hydraulic fluid
B Locks the wheel hub
C Adjusts tire pressure
D Moves steering linkage
Answer: D. Moves steering linkage. The Pitman arm transfers output from the steering box to the linkage.
What does an idler arm support?
A Steering wheel airbag
B Power-steering pump shaft
C Brake master cylinder
D Opposite steering linkage side
Answer: D. Opposite steering linkage side. An idler arm supports the linkage opposite the Pitman arm.
Why is power steering assist provided?
A Reduce driver steering effort
B Increase engine compression
C Cool the transmission
D Raise tire pressure
Answer: A. Reduce driver steering effort. Assistance reduces the force the driver must apply at the steering wheel.
What supplies assist torque in electric power steering?
A Fuel pump
B Water pump
C Starter ring gear
D Electric motor
Answer: D. Electric motor. An electric motor adds torque to the steering system.
Which source commonly drives hydraulic steering assist?
A Wheel bearing
B Radiator fan
C Alternator stator
D Engine-driven pump
Answer: D. Engine-driven pump. A hydraulic power-steering pump is commonly driven by the engine.
What does steering ratio compare?
A Fuel flow to engine speed
B Tire width to wheelbase
C Steering-wheel angle to road-wheel angle
D Pump pressure to coolant flow
Answer: C. Steering-wheel angle to road-wheel angle. Steering ratio relates steering-wheel rotation to road-wheel turning angle.
During a turn, which front wheel usually needs the larger steering angle?
A Outer wheel
B Inner wheel
C Both exactly equal
D Rear wheel only
Answer: B. Inner wheel. The inner wheel follows a tighter path and needs a larger angle.
Which geometry helps the inner and outer wheels follow different turn radii?
A Ackermann steering
B Camber thrust
C Toe-in setting
D Caster trail
Answer: A. Ackermann steering. Ackermann geometry accounts for the different radii of the inner and outer wheels.
What does positive caster describe?
A Axis tilts rearward at top
B Wheel top tilts inward
C Wheel fronts point inward
D Axle slopes downward
Answer: A. Steering axis tilts rearward at top. Positive caster places the steering-axis upper end behind its lower end.
What does negative camber mean?
A Wheel front points inward
B Wheel top tilts inward
C Steering axis tilts rearward
D Wheel toe points outward
Answer: B. Wheel top tilts inward. Negative camber means the top of the wheel leans inward relative to the vehicle.
What does toe-in describe?
A Wheel tops tilt inward
B Steering axis tilts rearward
C Rear wheels steer outward
D Wheel fronts point inward
Answer: D. Wheel fronts point inward. Toe-in means the front edges of the wheels are closer together than the rear edges.
Which part is held by the driver to command direction?
A Tie rod
B Steering wheel
C Steering knuckle
D Idler arm
Answer: B. Steering wheel. The driver applies steering input through the steering wheel.
What converts steering-gear output into wheel movement?
A Steering linkage
B Fuel system
C Cooling circuit
D Exhaust pipe
Answer: A. Steering linkage. Linkage rods and arms transfer steering-gear motion to the road wheels.
What does wheel alignment specify?
A Wheel angles and positions
B Fuel injector timing
C Engine valve lift
D Gearbox oil pressure
Answer: A. Wheel angles and positions. Alignment describes wheel and steering geometry relative to vehicle and road.
Why can a collapsible steering column improve safety?
A It increases engine torque
B Absorbs crash energy
C It locks the front wheels
D It raises steering ratio
Answer: B. It absorbs energy in a crash. A collapsible column is designed to deform and reduce injury risk in a crash.
Which steering gear is common in many passenger cars?
A Worm and wheel only
B Chain and sprocket
C Rack and pinion
D Planetary gearset
Answer: C. Rack and pinion. Rack-and-pinion steering is widely used in passenger cars.
What does a steering intermediate shaft connect?
A Fuel tank to pump
B Radiator to engine
C Brake pedal to booster
D Column to steering gear
Answer: D. Column to steering gear. The intermediate shaft links the column to a remote steering gear.
What does a universal joint in a steering shaft accommodate?
A Fuel expansion
B Angular misalignment
C Coolant boiling
D Tire rolling loss
Answer: B. Angular misalignment. A steering shaft joint transmits rotation across an angle.
What can low power-steering fluid cause?
A Higher engine compression
B More tire camber
C Noisy or heavy steering
D Lower exhaust temperature
Answer: C. Noisy or heavy steering. Low fluid can reduce hydraulic assist and cause pump noise.
Which sensor can measure driver steering torque in EPS?
A Coolant sensor
B Fuel-level sender
C Torque sensor
D Knock sensor
Answer: C. Torque sensor. EPS uses a torque sensor to detect driver input and command assistance.