For a tension member, a critical limit state is…
A Net-section rupture
B Concrete shear
C Soil bearing
D Slab deflection
Answer: A. Net-section rupture. A tension member is checked for yielding, rupture and connection-related limit states.
A bolt in a lap joint can be checked for…
A Concrete creep
B Soil liquefaction
C Beam deflection only
D Shear and bearing
Answer: D. Shear and bearing. Bolt shear and plate bearing are common connection limit states.
An edge distance that is too small may cause…
A Improved block shear
B Higher friction always
C Edge tear-out
D No failure mode
Answer: C. Edge tear-out. Insufficient edge distance can allow material to tear out toward a plate edge.
A long bolted joint may require consideration of…
A Concrete shrinkage only
B Thermal conductivity
C Unequal force distribution
D Column shortening only
Answer: C. Unequal force distribution. Long joints can develop nonuniform force distribution and may require code-specific adjustments.
A fillet weld’s effective throat is measured…
A Through the shortest load path
B Along the leg only
C Across the plate width
D At the weld end only
Answer: A. Through the shortest load path. Effective throat is the shortest distance from root to face for a standard equal-leg fillet.
A weld defect that reduces effective area can…
A Increase ductility always
B Lower connection strength
C Eliminate residual stress
D Raise bolt pretension
Answer: B. Lower connection strength. Lack of fusion, cracks or inadequate size can reduce weld capacity.
An eccentric connection creates…
A Only axial strain
B No shear force
C Uniform temperature
D Additional moment
Answer: D. Additional moment. An offset between load line and connection centroid creates moment as well as force.
A built-up compression member may use…
A Slab mesh only
B Lacing or battens
C Concrete stirrups
D Decking only
Answer: B. Lacing or battens. Lacing or batten plates connect components so they act as a built-up column.
The slenderness ratio is effective length divided by…
A Section area
B Radius of gyration
C Yield stress
D Plate thickness
Answer: B. Radius of gyration. Column slenderness λ is commonly expressed as effective length over radius of gyration.
Increasing unbraced length generally makes a compression member…
A More stable
B More buckling-sensitive
C Stronger in tension
D Unaffected
Answer: B. More buckling-sensitive. Longer unbraced lengths reduce buckling resistance.
A beam’s plastic hinge region should have…
A Brittle welds
B Unbraced compression flange
C Sharp notches
D Adequate rotation capacity
Answer: D. Adequate rotation capacity. Ductile detailing and stable bracing support inelastic rotation capacity.
A laterally unsupported beam may fail by…
A Punching shear
B Net-section tension only
C Lateral-torsional buckling
D Bearing failure only
Answer: C. Lateral-torsional buckling. Lateral-torsional buckling combines lateral displacement and beam twist.
A beam web stiffener can help resist…
A Web buckling or crippling
B Steel corrosion only
C Torsion in foundations
D Concrete creep
Answer: A. Web buckling or crippling. Stiffeners support thin webs under concentrated loads or high shear.
A column splice should transfer…
A Required member forces
B Only coating thickness
C Only floor vibration
D Water pressure only
Answer: A. Required member forces. Splices should provide continuity for the design axial force, moment and shear.
An end-plate moment connection develops moment through…
A Only bolt shear
B Concrete bearing only
C A tension-compression couple
D Frictionless contact
Answer: C. A tension-compression couple. Moment transfer arises from tension and compression forces separated by a lever arm.
A simple shear connection is intended primarily to transfer…
A Full fixed-end moment
B Column axial load only
C Beam-end shear
D Torsion only
Answer: C. Beam-end shear. Simple connections are proportioned primarily for shear while allowing rotation.
A column base under moment may need…
A Only grout compression
B No anchor rods
C Welded rebar
D Anchor tension and bearing
Answer: D. Anchor tension and bearing. Moment can create a compression block and tension in anchor rods.
Slip-critical performance is important when…
A Plates may separate freely
B Bolts are decorative
C Connection slip must be limited
D Welds are omitted
Answer: C. Connection slip must be limited. Friction-grip joints are used where service slip or fatigue behavior matters.
A gusset plate should be checked for…
A Slab punching only
B Whitmore section yielding
C Footing settlement only
D Creep rupture of concrete
Answer: B. Whitmore section yielding. Gusset plates have potential yielding and buckling paths through their effective section.
Local buckling is affected by…
A Paint color
B Bolt grade only
C Span length only
D Width-to-thickness ratio
Answer: D. Width-to-thickness ratio. Thin plate elements are susceptible to local buckling depending on element proportions.
A compact section can develop…
A No elastic response
B Only axial tension
C No rotation
D Plastic moment capacity
Answer: D. Plastic moment capacity. Compact sections can sustain plastic stress distribution without premature local buckling.
A noncompact element may buckle…
A After first yield
B Before any stress
C Only after fracture
D Only under tension
Answer: A. After first yield. Noncompact elements may buckle after yielding but before full plastic strength develops.
A slender plate element may buckle…
A Before yielding fully
B Only after fracture
C Never in compression
D Only during welding
Answer: A. Before yielding fully. Slender elements can buckle locally before reaching yield stress.
A gantry girder supports…
A Roof drainage only
B Crane wheel loads
C Floor tiles
D Subsurface water
Answer: B. Crane wheel loads. Gantry girders carry moving crane wheel loads and associated vertical and horizontal effects.
Serviceability of a steel floor beam includes…
A Deflection and vibration
B Only rupture strength
C Only weld color
D Only bolt count
Answer: A. Deflection and vibration. Excessive deflection or vibration can impair use even when strength is adequate.