Structural steel is valued for…
A High strength and ductility
B Low stiffness only
C Brittle behavior only
D Zero maintenance needs
Answer: A. High strength and ductility. Steel provides high strength and useful ductility, with behavior depending on grade and detailing.
A tension member primarily carries…
A Bending only
B Compression only
C Axial pull
D Torsion only
Answer: C. Axial pull. Tension members transfer axial tensile force through their cross-section and connections.
A compression member can fail by…
A Only corrosion
B Buckling
C Thermal expansion
D Fatigue always
Answer: B. Buckling. Compression members may buckle before reaching material crushing strength.
A steel beam primarily resists…
A Tension only
B Water pressure
C Thermal flow
D Bending and shear
Answer: D. Bending and shear. Beams resist transverse loads through bending moment and shear force.
A limit state design checks…
A Only appearance
B Only construction speed
C Only material cost
D Safety and serviceability
Answer: D. Safety and serviceability. Limit-state design considers failure safety and acceptable service behavior.
Gross area of a tension plate includes…
A Bolt holes only
B Entire cross-section
C Weld throat only
D Net ligament only
Answer: B. Entire cross-section. Gross area is the full section before deductions for holes or other reductions.
Net area deducts…
A Bolt holes and openings
B Edge distance
C Plate length
D Weld length only
Answer: A. Bolt holes and openings. Net area accounts for material removed by holes along the failure path.
A bolted connection transfers load through…
A Paint film only
B Concrete cover
C Surface drainage
D Bolt and connected plates
Answer: D. Bolt and connected plates. Bolts transfer force through shear, bearing or friction depending on connection type.
A fillet weld commonly joins surfaces meeting at…
A A single point
B No interface
C A circular bore only
D An angle
Answer: D. An angle. Fillet welds are used at corners or T-joints between intersecting surfaces.
A butt weld joins members…
A At right angles only
B Through a pin
C In the same plane
D With no contact
Answer: C. In the same plane. Butt welds join members aligned in approximately the same plane.
A gusset plate commonly connects…
A Concrete slabs only
B Truss members at a joint
C Rail tracks only
D Column base grout
Answer: B. Truss members at a joint. Gusset plates collect and transfer forces between members meeting at a truss joint.
A tension member with bolt holes may fail by…
A Net-section rupture
B Concrete crushing
C Local foundation bearing
D Slab punching
Answer: A. Net-section rupture. Reduced net area can rupture when tensile stress exceeds its resistance.
Block shear failure combines…
A Bending and torsion only
B Buckling and fatigue only
C Tension and shear rupture
D Compression and bearing only
Answer: C. Tension and shear rupture. Block shear follows a path with shear planes and a tension plane around a connection.
A slender steel column is sensitive to…
A Paint thickness only
B Bolt color
C Effective length and restraint
D Weld appearance
Answer: C. Effective length and restraint. Buckling resistance depends strongly on unbraced length and end restraint.
Lateral-torsional buckling affects…
A Tension rods only
B Unrestrained beam compression flange
C Concrete footings
D Bolted lap plates only
Answer: B. Unrestrained beam compression flange. An unsupported compression flange can move laterally while the beam twists.
A lateral brace for a beam helps…
A Restrain compression flange
B Increase bolt holes
C Reduce steel grade
D Remove shear force
Answer: A. Restrain compression flange. Bracing limits lateral movement and twist of the compression flange.
High-strength friction-grip bolts transfer shear mainly through…
A Friction between plates
B Bolt bearing only
C Weld metal
D Concrete bond
Answer: A. Friction between plates. Pretension creates clamping force so friction resists slip at the faying surfaces.
Bearing-type bolts transfer force after…
A Contact with hole surface
B Concrete curing
C Plate melting
D Frictionless separation
Answer: A. Contact with hole surface. After slip, bolt shank and hole bearing transfer the applied shear.
A snug-tight bolt is installed to…
A Melt the washer
B Create a weld
C Allow loose movement
D Bring plates into firm contact
Answer: D. Bring plates into firm contact. Snug-tight installation brings connected plies into firm contact.
A column base plate distributes…
A Water to roof drains
B Column load to foundation
C Traffic to pavement
D Beam load to slab only
Answer: B. Column load to foundation. Base plates spread column forces over the supporting concrete foundation.
A gusseted base often transfers…
A Only paint load
B Water flow
C Large column forces
D Floor vibration only
Answer: C. Large column forces. Base plates and gussets transfer axial force, shear and moment to the foundation.
A beam-column connection may transfer…
A Only temperature
B Only surface water
C No structural force
D Shear and moment
Answer: D. Shear and moment. Connections can be detailed for simple shear or moment transfer.
Corrosion protection may include…
A Open drainage only
B Concrete aggregate
C Coatings or galvanizing
D Thermal expansion joints
Answer: C. Coatings or galvanizing. Protective coatings or galvanizing limit environmental corrosion of steel.
Fire can reduce steel strength and stiffness by…
A Heating the member
B Cooling the member
C Increasing section area
D Closing bolt holes
Answer: A. Heating the member. Elevated temperatures degrade mechanical properties and can cause large deformation.
A fatigue-sensitive steel detail should reduce…
A Member continuity
B Stress concentration
C Inspection access
D Load path clarity
Answer: B. Stress concentration. Smooth details and reduced stress concentrations improve fatigue performance.