Difficulty: Hard
In a hydrodynamic journal bearing, how is load-carrying pressure created?
A Oil pump pressure alone
B Magnetic attraction
C Fuel combustion pressure
D Wedge action in oil film
Answer: D. Wedge action in oil film. Journal motion draws viscous oil into a converging clearance and develops pressure.
On the Stribeck curve, what follows boundary lubrication as film parameter rises?
A Dry friction only
B Hydrostatic cooling
C Cavitation flow
D Mixed lubrication
Answer: D. Mixed lubrication. The usual progression is boundary, mixed, then full-film hydrodynamic lubrication.
Why is oil flow important even when pressure looks normal?
A Pressure equals fuel octane
B Flow sets compression ratio
C Pressure stops all wear
D Flow carries heat and lubricant
Answer: D. Flow carries heat and lubricant. Pressure alone does not prove adequate delivery flow to every component.
Excessive bearing clearance can affect oil pressure how?
A Increase leakage and lower pressure
B Stop oil oxidation
C Raise fuel pressure
D Reduce pump rotation speed
Answer: A. Increase leakage and lower pressure. Larger clearances permit more leakage, which may reduce system pressure.
A relief valve stuck partly open may cause what?
A Higher coolant concentration
B More fuel atomization
C Increased tire traction
D Low lubrication pressure
Answer: D. Low lubrication pressure. Oil bypassing continuously through the relief path can lower gallery pressure.
A filter bypass stays closed while the filter blocks. What risk rises?
A Fuel dilution
B Coolant overfill
C Oil starvation
D Exhaust restriction
Answer: C. Oil starvation. Without bypass flow, a severely restricted filter can limit oil supply to the engine.
A filter bypass stuck open may allow what?
A Coolant to enter sump
B Unfiltered oil circulation
C Fuel to reach bearings
D Exhaust gas into oil
Answer: B. Unfiltered oil circulation. Oil can circulate without full filtration when the bypass remains open.
What inlet condition can cause oil-pump cavitation?
A High outlet pressure only
B Low tire pressure
C High oil level
D Low suction pressure
Answer: D. Low suction pressure. Low pressure at the pump inlet can form vapor cavities that impair delivery.
During cornering, oil moves away from the pickup. What may follow?
A Higher coolant flow
B More fuel octane
C Temporary oil starvation
D Lower exhaust temperature
Answer: C. Temporary oil starvation. Slosh can uncover the pickup and interrupt oil supply.
Why can a dry-sump system suit sustained high lateral acceleration?
A It eliminates bearings
B It cools fuel directly
C Separate tank supports oil supply
D It removes the oil pump
Answer: C. Separate tank supports oil supply. The remote tank and scavenging layout help maintain lubrication during strong vehicle motion.
Why may a dry-sump scavenge stage exceed pressure-stage capacity?
A Raise fuel rail pressure
B Keep crankcase oil cleared
C Increase valve lift
D Reduce cylinder stroke
Answer: B. Keep crankcase oil cleared. High scavenging capacity helps return oil rapidly and keep the crankcase relatively clear.
An oil-cooler thermostat stuck open when cold may cause what?
A Immediate coolant boiling
B Higher fuel pressure
C Slow oil warm-up
D Lower oil capacity
Answer: C. Slow oil warm-up. Continuous cooler flow can delay oil reaching its intended operating temperature.
A failed oil-to-coolant cooler may produce which clue?
A Higher tire pressure
B Oil and coolant contamination
C Longer engine stroke
D Lower exhaust noise
Answer: B. Oil and coolant contamination. A breached heat exchanger can allow the two fluids to mix.
What does air entrainment do to a lubricating film?
A Makes film compressible
B Raises viscosity permanently
C Stops oil oxidation
D Increases bearing clearance
Answer: A. Makes film compressible. Air bubbles can reduce film stiffness and load-carrying ability.
Which additive helps control foam in engine oil?
A Antifoam agent
B Octane booster
C Antifreeze
D Fuel detergent
Answer: A. Antifoam agent. Antifoam additives reduce persistent foam in the lubricant.
Fuel dilution of oil commonly causes what change?
A Higher viscosity only
B Higher oil pressure
C Lower viscosity
D More film thickness
Answer: C. Lower viscosity. Fuel mixed into oil can thin the lubricant and reduce film strength.
Coolant entering the crankcase can cause what oil appearance?
A Clear blue oil
B Milky emulsion
C Dry powder
D Foam-free black oil
Answer: B. Milky emulsion. Water and coolant can emulsify with oil and produce a milky appearance.
How can severe polymer shear affect a multigrade oil?
A Raise octane rating
B Increase coolant flow
C Stop bearing rotation
D Reduce high-temperature viscosity
Answer: D. Reduce high-temperature viscosity. Mechanical shear can degrade viscosity modifiers and reduce viscosity retention.
Oil oxidation over time can contribute to what?
A Acid and deposits
B Higher fuel level
C Lower crankshaft speed
D More coolant pressure
Answer: A. Acid and deposits. Oxidation can form acids and deposit precursors such as sludge or varnish.
Blue exhaust smoke with falling oil level may indicate what?
A Coolant entering fuel
B Oil entering combustion
C Low tire pressure
D Clutch slip
Answer: B. Oil entering combustion. Burning lubricating oil can produce blue-tinted exhaust smoke.
A blocked crankcase breather may cause what?
A Higher oil viscosity index
B Excess crankcase pressure
C Lower fuel octane
D More radiator airflow
Answer: B. Excess crankcase pressure. Restricted ventilation can raise crankcase pressure and promote seal leakage.
A failed anti-drainback valve may cause what after long parking?
A Higher coolant pressure
B Delayed oil pressure after start
C More fuel atomization
D Reduced wheel alignment
Answer: B. Delayed oil pressure after start. Oil may drain from the filter or galleries, delaying pressure buildup at restart.
An oil warning lamp glows but a mechanical gauge reads normal pressure. What should be checked?
A Tire balance
B Fuel octane
C Switch and wiring
D Thermostat rating
Answer: C. Switch and wiring. A faulty pressure switch, connector, or wiring can trigger a false warning.
An oil-cooler thermostat stuck closed may cause what under high load?
A Excessive oil temperature
B Low fuel level
C Higher coolant freeze point
D Reduced engine displacement
Answer: A. Excessive oil temperature. Bypassing the cooler continuously can allow oil temperature to rise under load.
What surface damage can severe oil starvation cause in a bearing?
A Scuffing and wiping
B Polished paint only
C Tire cupping
D Valve-seat recession
Answer: A. Scuffing and wiping. Loss of the lubricating film can overheat and smear bearing surfaces.