Difficulty: Easy & Basic
What is the main purpose of engine lubrication?
A Increase compression ratio
B Cool the fuel tank
C Raise exhaust pressure
D Reduce friction and wear
Answer: D. Reduce friction and wear. Lubricating oil separates moving surfaces and reduces friction and wear.
Where is oil commonly stored in a wet-sump engine?
A Fuel rail
B Radiator tank
C Oil pan
D Intake plenum
Answer: C. Oil pan. A wet-sump system stores most engine oil in the oil pan below the crankcase.
Which component circulates engine oil?
A Oil pump
B Fuel injector
C Water pump
D Starter motor
Answer: A. Oil pump. The oil pump moves lubricant through galleries and engine clearances.
Why is an oil filter fitted?
A Raise fuel octane
B Remove contaminants
C Control valve timing
D Measure coolant level
Answer: B. Remove contaminants. The filter traps particles that could damage bearings and moving surfaces.
How does oil reach distant engine bearings?
A Fuel lines
B Radiator hoses
C Exhaust runners
D Oil galleries
Answer: D. Oil galleries. Machined galleries distribute pressurized oil through the engine.
Which instrument may indicate lubrication pressure?
A Tachometer
B Fuel level gauge
C Oil pressure gauge
D Speedometer
Answer: C. Oil pressure gauge. An oil-pressure gauge displays pressure in the lubrication circuit.
How is engine oil level commonly checked?
A Fuel rail sensor
B Radiator cap
C Odometer
D Dipstick
Answer: D. Dipstick. A dipstick measures oil level in the sump when checked as specified.
Which component screens debris before the pump?
A Oil cooler
B Oil strainer
C Pressure sensor
D Drain plug
Answer: B. Oil strainer. The pickup strainer screens larger debris at the pump inlet.
What limits excessive lubrication-system pressure?
A Relief valve
B Thermostat
C Fuel regulator
D Fan clutch
Answer: A. Relief valve. A pressure-relief valve bypasses oil when pressure exceeds its setting.
Which surfaces receive oil to reduce sliding wear?
A Radiator fins
B Tire treads
C Brake pads
D Engine bearings
Answer: D. Engine bearings. Oil lubricates bearing surfaces such as crankshaft and camshaft journals.
What type of film can support a rotating journal?
A Hydrodynamic oil film
B Dry friction film
C Fuel vapor film
D Coolant film
Answer: A. Hydrodynamic oil film. Journal rotation can draw oil into a converging gap and develop supporting pressure.
During cold start, which lubrication regime may briefly dominate?
A Boundary lubrication
B Full-film cooling
C Hydrostatic air flow
D Dry-sump scavenging
Answer: A. Boundary lubrication. Before a full oil film forms, surface additives and thin films help limit contact wear.
What property describes oil resistance to flow?
A Viscosity
B Density
C Octane rating
D Boiling point
Answer: A. Viscosity. Viscosity measures a fluid’s resistance to flow or shear.
What does an oil-filter bypass valve permit?
A Fuel flow into sump
B Coolant flow past pump
C Oil flow around a restricted filter
D Exhaust flow through intake
Answer: C. Oil flow around a restricted filter. A bypass maintains oil flow if filter pressure drop becomes excessive.
Where is oil held in a dry-sump system?
A Wet oil pan only
B Fuel tank
C External reservoir
D Radiator header
Answer: C. External reservoir. Dry-sump systems store oil in a separate tank.
Which component can remove heat from engine oil?
A Fuel injector
B Air cleaner
C Oil cooler
D Brake booster
Answer: C. Oil cooler. An oil cooler transfers heat from lubricant to air or coolant.
What is an oil pump pickup connected to?
A Exhaust valve
B Fuel rail
C Cooling fan
D Sump inlet
Answer: D. Sump inlet. The pickup draws oil from the sump toward the pump.
Which component helps prevent oil escaping at a rotating shaft?
A Fuel filter
B Oil seal
C Radiator cap
D Thermostat
Answer: B. Oil seal. A shaft seal limits lubricant leakage around a rotating component.
What separates many moving metal surfaces?
A Air filter
B Lubricating film
C Fuel vapor
D Exhaust soot
Answer: B. Lubricating film. An oil film reduces direct metal-to-metal contact.
Where is used engine oil commonly drained?
A Oil pan drain plug
B Fuel filler neck
C Radiator drain only
D Air-filter housing
Answer: A. Oil pan drain plug. Removing the drain plug allows sump oil to flow out during service.
Which additive helps keep deposits from bonding to surfaces?
A Antifreeze
B Octane booster
C Foam agent
D Detergent
Answer: D. Detergent. Detergent additives help control deposits on engine surfaces.
What do dispersant additives help keep suspended?
A Coolant bubbles
B Fuel droplets
C Contaminant particles
D Exhaust valves
Answer: C. Contaminant particles. Dispersants keep fine contaminants suspended so they can be captured or drained.
Which additive family reduces wear under severe contact?
A Anti-wear additives
B Colorants
C Fragrance additives
D Antifoam only
Answer: A. Anti-wear additives. Anti-wear additives form protective films under boundary or mixed lubrication.
What warning may indicate dangerously low oil pressure?
A High-beam indicator
B Oil-pressure lamp
C Turn signal
D Fuel-door light
Answer: B. Oil-pressure lamp. The oil-pressure warning lamp signals pressure below the system’s threshold.
Which guide should determine the engine oil grade?
A Oil color alone
B Vehicle maker specification
C Tire label
D Fuel cap text
Answer: B. Vehicle maker specification. Use the viscosity and performance level specified by the vehicle manufacturer.