Difficulty: Easy & Basic
What does an SAE engine-oil grade classify?
A Viscosity properties
B Additive color
C Fuel octane
D Coolant concentration
Answer: A. Viscosity properties. SAE grades classify rheological viscosity properties, not every performance characteristic.
Which information does an API service category chiefly describe?
A Oil-pan capacity
B Oil performance level
C Crankshaft speed
D Coolant boiling point
Answer: B. Oil performance level. API service categories indicate performance requirements for engine-oil service.
In an oil grade such as 5W-30, what does W signify?
A Water content
B Wear limit
C Wide bearing clearance
D Winter low-temperature class
Answer: D. Winter low-temperature class. The W grade includes specified low-temperature cranking and pumping criteria.
Why is SAE 5W-30 called a multigrade oil?
A Contains two base oils
B Meets W and hot-grade limits
C Works only in winter
D Has two API labels
Answer: B. Meets W and hot-grade limits. A multigrade meets requirements for a W grade and a high-temperature viscosity grade.
What does a higher viscosity index generally indicate?
A Higher oil density
B Lower pressure always
C Smaller viscosity change with temperature
D More detergent additive
Answer: C. Smaller viscosity change with temperature. A higher viscosity index means viscosity changes less with temperature over the measured range.
In a dry-sump layout, where is most oil stored?
A Crankcase oil pan
B Radiator core
C Fuel reservoir
D Separate external tank
Answer: D. Separate external tank. A dry-sump system uses a separate oil tank rather than relying on a deep sump.
What does a scavenge pump do in a dry-sump system?
A Raises fuel pressure
B Returns oil from crankcase
C Circulates engine coolant
D Filters intake air
Answer: B. Returns oil from crankcase. Scavenge stages remove oil from the crankcase and return it to the tank.
What feature distinguishes a wet-sump layout?
A Oil stored in external tank
B No oil pump fitted
C Oil mixed with fuel
D Oil stored in pan
Answer: D. Oil stored in pan. A wet-sump engine stores its main oil supply in the sump pan.
Why are baffles placed in some oil pans?
A Increase compression ratio
B Cool the fuel rail
C Open the exhaust valve
D Limit oil slosh
Answer: D. Limit oil slosh. Baffles help keep oil near the pickup during acceleration and cornering.
What can happen if oil slosh uncovers the pickup?
A Fuel pressure rises
B Coolant boils immediately
C Oil viscosity doubles
D Pump may draw air
Answer: D. Pump may draw air. An uncovered pickup can interrupt oil supply and admit air into the pump.
Which pump design uses an inner and outer rotor?
A Gerotor pump
B Piston pump
C Diaphragm pump
D Vane fuel pump
Answer: A. Gerotor pump. A gerotor uses eccentric inner and outer rotors to move oil.
What do meshing pump gears create?
A Exhaust scavenging
B Coolant vapor
C Fuel-air swirl
D Oil displacement chambers
Answer: D. Oil displacement chambers. Gear-tooth spaces carry oil from inlet to outlet.
Which condition may lower hot-idle oil pressure?
A High tire pressure
B Closed radiator fan
C Low viscosity or worn clearances
D High fuel octane
Answer: C. Low viscosity or worn clearances. Hot, thinner oil or enlarged clearances can reduce pressure at low engine speed.
What generally happens to oil viscosity as temperature rises?
A It decreases
B It increases sharply
C It becomes zero
D It stays constant
Answer: A. It decreases. Most lubricating oils become less viscous as temperature rises.
How can fuel dilution affect engine oil?
A Lower viscosity and protection
B Raise viscosity without limit
C Remove all contaminants
D Increase oil level accuracy
Answer: A. Lower viscosity and protection. Fuel contamination can thin oil and weaken its lubricating film.
What can aerated oil do to a bearing film?
A Reduce film strength
B Increase oil density greatly
C Stop oxidation
D Raise octane rating
Answer: A. Reduce film strength. Air bubbles can make the oil supply compressible and weaken load-carrying films.
What risk can severe oil overfill create?
A Fuel tank vents
B Radiator pressure falls
C Crankshaft aerates oil
D Oil filter stops rotating
Answer: C. Crankshaft aerates oil. Excess oil can be whipped by rotating parts and become aerated.
What risk follows a very low oil level?
A Higher coolant flow
B More fuel atomization
C Pickup starvation
D Lower exhaust temperature
Answer: C. Pickup starvation. A low level can uncover the pickup and interrupt lubrication.
Why might an oil cooler thermostat be fitted?
A Raise fuel pressure
B Avoid excessive oil cooling
C Change viscosity grade
D Open the radiator cap
Answer: B. Avoid excessive oil cooling. A thermostat can bypass or regulate cooler flow until oil warms appropriately.
What can oil oxidation promote over time?
A Higher octane
B Lower tire grip
C Varnish and sludge
D Coolant foaming only
Answer: C. Varnish and sludge. Oxidation products can contribute to deposits such as varnish and sludge.
What can laboratory oil analysis help monitor?
A Vehicle wheelbase
B Wear metals and contamination
C Fuel tank capacity
D Brake rotor diameter
Answer: B. Wear metals and contamination. Oil analysis can track wear metals, contamination, and changes in lubricant condition.
What should determine oil replacement timing?
A Oil color alone
B Ambient noise
C Manufacturer service schedule
D Tire pressure
Answer: C. Manufacturer service schedule. Follow the vehicle maker’s interval and severe-service guidance.
Why can overly viscous oil at cold start be harmful?
A Higher coolant concentration
B Slower flow to components
C Faster fuel evaporation
D Lower battery voltage
Answer: B. Slower flow to components. Very viscous cold oil can flow slowly and delay lubrication to components.
What does a dipstick reading above maximum suggest?
A Excess oil level
B Low fuel level
C High coolant pressure
D Worn tire tread
Answer: A. Excess oil level. An above-maximum level may indicate overfill or contamination and should be investigated.
How may worn bearing clearances affect oil pressure?
A Stop oil oxidation
B Increase leakage flow
C Reduce pump rotation
D Raise fuel octane
Answer: B. Increase leakage flow. Larger clearances increase leakage and can reduce pressure under some operating conditions.