A downstream structure raises channel water level upstream. Expected profile?
A Drawdown only
B Hydraulic jump downstream only
C Backwater curve
D Uniform flow necessarily
Answer: C. Backwater curve. Downstream control can raise the upstream depth, creating a backwater profile.
A channel transition becomes too narrow for the imposed flow. It may cause…
A Zero discharge
B Pump cavitation
C Critical control or choking
D A closed pressure pipe
Answer: C. Critical control or choking. A constriction can force critical flow and create upstream afflux if capacity is insufficient.
A hydraulic jump is best positioned in a stilling basin to…
A Increase turbine head
B Dissipate excess energy
C Prevent all turbulence
D Raise pump suction pressure
Answer: B. Dissipate excess energy. Stilling basins contain jumps to dissipate energy and reduce downstream scour.
A jump with large incoming Froude number generally has…
A Greater energy dissipation
B No depth change
C Lower turbulence
D No momentum change
Answer: A. Greater energy dissipation. Stronger supercritical inflow produces a more energetic jump and larger losses.
A mobile-bed channel near a structure needs assessment for…
A Scour and sediment movement
B Only pipe friction
C Pump affinity
D Draft-tube pressure
Answer: A. Scour and sediment movement. Bed material transport and local scour can undermine hydraulic structures.
Pump NPSH available should exceed…
A Pump shutoff head
B System static lift only
C Atmospheric pressure head always
D NPSH required
Answer: D. NPSH required. Adequate margin between available and required NPSH helps prevent cavitation.
Operating far to the right of a pump curve can cause…
A Zero discharge always
B Lower velocity everywhere
C Guaranteed best efficiency
D Runout and overload risk
Answer: D. Runout and overload risk. Runout operation may exceed motor capacity and move away from the preferred range.
Operating at pump shutoff means…
A Maximum discharge
B Best efficiency always
C No pressure rise
D Nearly zero discharge
Answer: D. Nearly zero discharge. At shutoff, the discharge valve is closed and flow is nearly zero while head is developed.
A positive-displacement pump should generally include…
A Pressure relief protection
B No discharge line
C A draft tube
D An open free jet
Answer: A. Pressure relief protection. A blocked discharge can rapidly raise pressure in a positive-displacement pump.
An air vessel on a reciprocating pump can…
A Increase channel roughness
B Create a hydraulic jump
C Smooth flow fluctuations
D Eliminate all friction
Answer: C. Smooth flow fluctuations. Air vessels reduce discharge variation and can lower acceleration head.
Specific speed helps classify machines using…
A Only impeller color
B Speed, flow and head
C Pipe roughness alone
D Channel width only
Answer: B. Speed, flow and head. Specific speed combines rotational speed with discharge and head for machine similarity and selection.
Model and prototype hydraulic machines use similarity laws to compare…
A Concrete cover
B Map coordinates
C Performance at scaled conditions
D Water chemistry only
Answer: C. Performance at scaled conditions. Similarity relations help predict prototype performance from model testing.
A high-head, low-flow site commonly favors…
A Kaplan turbine
B Impulse turbine
C Axial pump
D Reciprocating turbine
Answer: B. Impulse turbine. Pelton impulse turbines are suited to high head and comparatively low discharge.
A low-head, high-flow site commonly favors…
A Pelton wheel
B Kaplan turbine
C Reciprocating pump
D High-head Francis only
Answer: B. Kaplan turbine. Kaplan turbines serve low-head, high-discharge conditions.
A reaction turbine draft tube should avoid…
A Air entry and flow separation
B Pressure recovery
C Tailwater connection
D Smooth expansion
Answer: A. Air entry and flow separation. Poor draft-tube flow can cause separation, losses and unstable operation.
A pump impeller transfers energy through…
A Hydraulic jump only
B Change in fluid angular momentum
C Surface tension
D Concrete bearing
Answer: B. Change in fluid angular momentum. The rotor changes fluid angular momentum, producing energy transfer described by turbomachinery relations.
A turbine guide vane commonly controls…
A Concrete slump
B Tailwater chemistry
C Flow direction and discharge
D Pipe diameter
Answer: C. Flow direction and discharge. Guide vanes regulate flow into a reaction turbine runner and control output.
Parallel pumps may not share flow equally when…
A They connect common nodes
B Head is equal
C Discharge is summed
D Their curves differ
Answer: D. Their curves differ. Different pump curves and branch resistances can produce unequal branch flows.
A pump system curve includes static head and…
A Turbine torque only
B Channel top width
C Runner blade angle only
D Flow-dependent losses
Answer: D. Flow-dependent losses. System head combines static elevation difference with losses that vary with discharge.
A surge tank in a long water conduit can reduce…
A Normal depth
B Pressure transients
C Pump efficiency losses only
D Turbine runner speed
Answer: B. Pressure transients. Surge tanks moderate pressure and flow changes in long hydraulic conduits.
A hydraulic jump can be suppressed by changing…
A Fluid density only
B Channel color
C Tailwater or control conditions
D Pump impeller diameter only
Answer: C. Tailwater or control conditions. Jump location depends on upstream momentum and downstream tailwater depth.
A short-crested obstruction can cause local…
A Uniform flow everywhere
B Zero energy change
C Static fluid only
D Rapidly varied flow
Answer: D. Rapidly varied flow. Obstructions and transitions produce local acceleration and rapidly varied depths.
Cavitation in a turbine often threatens the…
A Runner and draft tube
B Reservoir embankment only
C Channel bed slope
D Pump motor windings
Answer: A. Runner and draft tube. Low pressure regions can create cavities that damage runner or draft-tube surfaces.
A hydraulic machine selection should consider…
A Duty point and operating range
B Only maximum head
C Only machine color
D Only initial purchase price
Answer: A. Duty point and operating range. Selection should match head, discharge, efficiency, cavitation limits and operating variation.
Field verification after installation should compare…
A Measured performance with design
B Only nameplate color
C Only foundation depth
D Only ambient temperature
Answer: A. Measured performance with design. Commissioning checks confirm head, discharge, power, vibration and controls against the intended duty.