For a rectangular channel, hydraulic depth equals…
A Channel width
B Wetted perimeter
C Hydraulic radius
D Flow depth
Answer: D. Flow depth. For a rectangle, A/T = (by)/b = y.
The specific-force function in a channel combines…
A Momentum and hydrostatic effects
B Only friction loss
C Pump power and head
D Surface tension and viscosity
Answer: A. Momentum and hydrostatic effects. Specific force represents momentum flux and hydrostatic pressure force per unit weight.
A backwater curve is commonly caused by…
A A sudden dry bed
B Pump cavitation
C Uniform flow only
D Downstream water-level control
Answer: D. Downstream water-level control. A downstream control can raise depths upstream, forming a gradually varied profile.
A drawdown curve represents depth…
A Rising after a jump
B Constant everywhere
C Inside a closed pump
D Falling toward a control
Answer: D. Falling toward a control. Drawdown profiles describe gradually decreasing depth toward a control section.
At fixed discharge, critical depth gives…
A Maximum friction loss
B Minimum specific energy
C Zero velocity
D Maximum normal depth
Answer: B. Minimum specific energy. Critical depth corresponds to minimum specific energy for a given discharge and section.
A rectangular-channel hydraulic jump relates sequent depths through…
A Momentum conservation
B Bernoulli without losses
C Pump affinity laws
D Manning roughness only
Answer: A. Momentum conservation. Momentum conservation provides the conjugate-depth relation across a short jump.
A sluice gate commonly produces…
A Supercritical flow downstream
B A turbine draft tube
C Uniform pressure pipe flow
D A static reservoir
Answer: A. Supercritical flow downstream. Flow under a gate may accelerate into a shallow supercritical jet.
The channel bed slope for uniform flow is balanced by…
A Pump suction head
B Critical depth
C Friction slope
D Atmospheric pressure
Answer: C. Friction slope. Uniform flow requires energy slope equal to bed slope.
A centrifugal pump curve commonly plots head against…
A Concrete strength
B Discharge
C Channel width
D Turbine runner angle only
Answer: B. Discharge. Pump characteristic curves show head and efficiency as functions of discharge or speed.
The system curve represents…
A Pump casing thickness
B Head required versus discharge
C Fluid density versus temperature
D Turbine speed only
Answer: B. Head required versus discharge. The system curve describes static and friction head required at each flow rate.
Two pumps in series primarily increase…
A Fluid density
B Pipe diameter
C Channel top width
D Available head
Answer: D. Available head. Series operation adds pump heads at a common flow rate.
Two pumps in parallel primarily increase…
A Suction pressure always
B Fluid density
C Runner diameter only
D Available discharge
Answer: D. Available discharge. Parallel operation combines discharges at a common head.
Pump affinity law at fixed impeller diameter gives Q proportional to…
A Speed squared
B Speed cubed
C Rotational speed
D Inverse speed
Answer: C. Rotational speed. For geometrically similar operation, discharge scales approximately with rotational speed.
Under the same affinity assumptions, pump head scales with…
A Speed
B Speed squared
C Speed cubed
D Inverse speed
Answer: B. Speed squared. Pump head varies approximately with the square of speed.
Under the same affinity assumptions, pump power scales with…
A Speed
B Speed squared
C Speed cubed
D Inverse speed
Answer: C. Speed cubed. Pump power varies approximately with the cube of rotational speed.
Cavitation in a pump can cause…
A Higher liquid density
B Improved efficiency always
C Noise and impeller damage
D A hydraulic jump
Answer: C. Noise and impeller damage. Bubble formation and collapse can cause noise, vibration, pitting and performance loss.
A reaction turbine runner experiences…
A Only free-jet impact
B Pressure change through runner
C No pressure variation
D Only atmospheric flow
Answer: B. Pressure change through runner. In reaction turbines, pressure changes as water flows through the runner.
A draft tube also allows a reaction runner to be set…
A Above tailwater level
B Below the channel bed only
C Inside a pump casing
D At atmospheric vacuum
Answer: A. Above tailwater level. A draft tube can recover pressure and permit the runner to sit above tailwater.
A Pelton bucket divides the jet into…
A Four closed pipes
B A pressure wave
C Two streams
D One suction vortex
Answer: C. Two streams. The bucket splitter divides the jet into two flows deflected around the bucket.
A Francis turbine has flow that is…
A Purely tangential
B Mixed radial and axial
C Purely longitudinal
D Only reciprocating
Answer: B. Mixed radial and axial. Francis turbines use mixed-flow passage from radial entry toward axial discharge.
A Kaplan runner is suited to…
A Low head and high flow
B High head and tiny flow
C Zero head
D Pumped storage only
Answer: A. Low head and high flow. Kaplan machines are axial-flow reaction turbines suited to relatively low head and high discharge.
The turbine draft tube exit is normally near…
A Tailwater level
B The reservoir surface
C The pump suction
D The runner inlet only
Answer: A. Tailwater level. The draft tube discharges to the tailrace or tailwater.
Hydraulic turbine efficiency compares shaft output with…
A Generator voltage only
B Runner mass
C Hydraulic input power
D Channel width
Answer: C. Hydraulic input power. Efficiency is useful shaft power divided by hydraulic power supplied.
A pump operating point occurs where pump curve meets…
A System curve
B Channel rating curve
C Turbine velocity triangle
D Manning equation only
Answer: A. System curve. The intersection balances pump head with the system head requirement.
A pump suction line should limit…
A Discharge pipe length only
B Turbine draft pressure
C Channel roughness only
D Air leakage and head loss
Answer: D. Air leakage and head loss. Suction-side losses and air leaks reduce available NPSH and can impair operation.